Resumo do conteúdo contido na página número 1
Compact-Pro™ 44
Owner/Operator Manual
Manuel Du Propriétaire/Utilisateur
Models
991072 – Compact-Pro 44
03993700 11/09
ENGLISH
Printed in USA
FRANÇAIS
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Storage . . . . . . . . . . . . . . . . . . . . . . . . . 30 Assembly . . . . . . . . . . . . . . . . . . . . . . . 10 Accessories . . . . . . . . . . . . . . . . . . . . . 30 Controls and Features. . . . . . . . . . . . . 11 Service Parts . . . . . . . . . . . . . . . . . . . . 30 Operation . . . . . . . . . . . . . . . . . . . . . . . 12 Specifications . . . . . . . . . . . . . . . . . . . 31 Maintenance Schedule
Resumo do conteúdo contido na página número 3
� Record Unit Model and Serial numbers DEALER DELIVERY here. Dealer should: 1. Test brakes after unit is assembled to be sure adjustment has not been disturbed in shipment (See Parking Brake Interlock System on page 12). Wheel � Record Engine Model and Serial numbers brakes are properly adjusted at factory. here. 2. Check the safety interlock system to make sure that it is functioning properly. With operator on seat, unit must not start unless steering levers are in neutral (N) and Po
Resumo do conteúdo contido na página número 4
SAFETY WARNING: This cutting machine WARNING: POTENTIALLY is capable of amputating hands HAZARDOUS SITUATION! If not and feet and throwing objects. avoided, COULD RESULT in Failure to observe the safety death or serious injury. instructions in the manuals and on decals could result in serious injury or death. CAUTION: POTENTIALLY Slopes are a major factor related HAZARDOUS SITUATION! If not to loss-of-control and tip-over avoided, MAY RESULT in minor or accidents. Operation on all slop
Resumo do conteúdo contido na página número 5
6 2 5 1 4 3 2 OF4340 Figure 2 � If machine stops going uphill, stop 1. DANGER! TO AVOID SERIOUS blade and back down slowly. INJURY OR DEATH � Avoid sudden turns. Read Owner/Operator Manual. � Keep safety devices (guards, shields, switches, etc.) in place and working. � Check interlock system per manual before use. OL1801 � Understand location and function of all Keep children and others away controls. from unit while operating. � Never allow operation by untrained persons. 2. DANGER! ROTA
Resumo do conteúdo contido na página número 6
3. WARNING! SAFETY RULES Do not operate mower unless guards are in Read, understand, and follow all safety operating position or bagger is attached. practices in Owner/Operator Manual before beginning assembly. Failure to follow Always stand clear of discharge instructions could result in personal injury area. and/or damage to unit. ALWAYS remove key and/or wire from spark plug before assembly. Unintentional engine OL4430 start up can cause death or serious injury. Do not operate mower
Resumo do conteúdo contido na página número 7
NEVER operate unit after or during the use of Start and operate unit only when seated in medication, drugs or alcohol. Safe operation operator’s position. Steering control levers requires your complete and unimpaired must be in neutral, PTO disengaged and attention at all times. parking brake set when starting engine. DO NOT wear loose clothing or jewelry and Use care when approaching blind corners, tie back hair that may get caught in rotating shrubs, trees or other objects that may parts.
Resumo do conteúdo contido na página número 8
Know the weight of loads. Limit loads to those This product is equipped with an internal you can safely control and the unit can safely combustion type engine. DO NOT use unit on handle. or near any unimproved, forest-covered or brush covered land unless exhaust system is Disengage PTO when attachment is not in equipped with a spark arrester meeting use. ALWAYS turn off power to attachment applicable local, state or federal laws. A spark when travelling, crossing driveways, etc. arrester
Resumo do conteúdo contido na página número 9
ALWAYS wear safety glasses and protective NEVER store unit with fuel in fuel tank, inside gear near battery. Use insulated tools. a building where any ignition sources are present. DO NOT TIP battery beyond a 45° angle in any direction. Shut off fuel and allow engine to cool completely before storing in closed area or ALWAYS keep batteries out of reach of covering unit. children. Clean grass and debris from unit, especially Battery posts, terminals and related from around muffler and eng
Resumo do conteúdo contido na página número 10
ASSEMBLY 2 1 WARNING: AVOID INJURY. 1 Read and understand entire 3 Safety section before proceeding. UNIT ASSEMBLY Package Contents: Unit, Mower Deck and Literature Pack Preparation Checklist Refer to the Owner/Operator manual as required. 1. Unpack Unit - Remove shrink wrap and packaging materials. 2. Remove Unit From Container - Open Bypass Valves (dump valves) (See 1. Steering 3. Mounting Moving the Unit with the Engine Off on Levers Hardware page 16). 2. Seat Push unit from contain
Resumo do conteúdo contido na página número 11
CONTROLS AND FEATURES 16 10 2 15 3 1 9 13 11 4 7 14 6 8 12 5 OM4090 OM4085 OF4035 Figure 4 OF4095 1. Fuel Tanks and Caps 9. Battery 2. Steering Levers 10. Fuel Shut Off Valve 3. Hydraulic Oil Reservoir 11. Mower Lift Pedal 4. Ignition Switch 12. Mower Deck 5. Hour Meter 13. Mower Lift Lock 6. Throttle Lever 14. Seat Adjustment Lever 7. Choke Control 15. Parking Brake 8. Power Take Off (PTO) Switch 16. Bypass Valve Lever GB - 11
Resumo do conteúdo contido na página número 12
OPERATION Steering Levers WARNING: AVOID INJURY. Read and understand entire Safety section before proceeding. B A CONTROLS AND FEATURES See Figure 4 for Controls and Features locations. Safety Interlock System D C WARNING: Safety interlock system failure and improper operation of unit can result in The steering levers control speed and death or serious injury. Test this direction. In addition, they will stop the unit. system each time the unit is A. For reverse travel, pull both steeri
Resumo do conteúdo contido na página número 13
Put cutting height adjustment pin in desired Throttle Lever hole. Push mower lift pedal forward and hold The throttle lever changes 1 it while pushing down on the lift lock. Slowly the engine speed. Move lower mower lift pedal until deck lift contacts the throttle lever to Fast (1) cutting height adjustment pin. to increase engine speed. Move the lever to Slow (2) Fuel Shut-Off Valve to decrease engine speed. Use this valve to control fuel flow from left or right fuel tank. Open the
Resumo do conteúdo contido na página número 14
The alert starts counting down two hours GASOLINE before the maintenance is due. The meter IMPORTANT: ALWAYS use gasoline that flashes the word, "Now," when it reaches the meets the following guidelines: maintenance time. � Clean, fresh gasoline. Press and hold the toggle button to reset the � A minimum of 87 octane/87 AKI (91 maintenance clock to zero after perfoming RON). High altitude use may require a the service. different octane. Consult your engine NOTE: The hour meter is preprog
Resumo do conteúdo contido na página número 15
To stop the engine: 3. Check Engine Fuel and Crankcase Oil 1. Bring the steering levers to neutral. Disengage the PTO and engage the Check and add fuel if required. Check that parking brake. engine crankcase oil is full. Follow Engine 2. Move the throttle lever to the “Slow” Manual Maintenance Schedule. position. 4. Check Tire Pressure 3. Turn the ignition key to the “Off” position. See Specifications on page 31 for correct tire TO MOW WITH UNIT pressure. Operate the unit only when s
Resumo do conteúdo contido na página número 16
MOVING THE UNIT WITH THE FOR BEST PERFORMANCE ENGINE OFF Cut grass when it is dry. Keep mower blades sharp. IMPORTANT: Never tow unit. Keep mower deck properly levelled. 1. Shut OFF engine. 2. Place seat in the service position (See Adjust anti-scalp rollers to prevent scalping. Service Position on page 18). Do not set height of cut too low. For very tall 3. Pull the right and left bypass levers to grass, mow twice. the neutral position. Do not travel too fast. Mow with the engine set at full
Resumo do conteúdo contido na página número 17
MAINTENANCE SCHEDULE Proper maintenance can prolong the life of unit. The following charts show the WARNING: AVOID INJURY. recommended service schedule. More Read and understand entire frequent service may be required due to Safety section before proceeding. working conditions (heavy loads, high ambient temperatures, dusty conditions, or airborne debris). See the maintenance instructions in the Engine Manual for additional information. Period Service Task Check Safety Interlock WARNING:
Resumo do conteúdo contido na página número 18
Period Service Task Follow Engine Manual Perform scheduled engine maintenance. Refer to Each Maintenance Schedule engine manual for detailed instructions. Use Check Mower Blades Check mower blades for wear. Sharpen or replace Every as needed. See Mower Blades on page 20. 25 Hours Check Air FIlter Check air filter for dirt. Clean as required. Follow Engine Manual for maintenance schedule. Every Lubricate Unit Oil all pivot points and pin connections. Grease 50 lube fittings. See Lubricat
Resumo do conteúdo contido na página número 19
To Add Hydraulic Fluid: 1 2 1. Remove the cap from the expansion 2 tank. 2. Fill the expansion tank with 20W-50 engine oil with an SL API classification until oil level reaches the cold fill line on the tank. 3. Install the expansion tank cap and then 3 purge the system. See Purging the Hydraulic System on page 20. The hydraulic fluid should be at the cold fill line of the expansion tank. 4 OF4310 1. Service Position 2. Steering Levers 3. Parking Brake 4. Battery Figure 6 HYDRAULIC FLUID
Resumo do conteúdo contido na página número 20
9. Follow the instructions in To Add MOWER BLADES Hydraulic Fluid: on page 19. Remove 1 2 CAUTION: Use sturdy gloves or padding to protect hands when working with mower blades. 1. Turn the engine off. Remove the ignition 3 key. Remove the ignition wire from the spark plugs. 2. Remove the bolts, cup washer, and blades from the spindle shafts. Replace 1. Put the blades, cup washers, and the bolts back on the spindle shafts. 4 2. Tighten the bolts to a torque of 115-160 lbf-ft (156-217 N�m)
