Resumo do conteúdo contido na página número 1
Operator’s Manual
Auto Mower
Please read the Operator’s Manual carefully and make sure you
understand the instructions before using the machine E En ng glliis sh h
E En ng glliis sh h
Resumo do conteúdo contido na página número 2
Operator’s Manual for Auto Mower Contents Introduction ................................................ 4 Menu functions ..........................................29 Congratulations .........................................4 Main menu .............................................29 Symbols ...................................................... 5 1. Commands .........................................30 Symbols on Auto Mower ..........................5 2. Timer ........
Resumo do conteúdo contido na página número 3
INTRODUCTION Introduction Congratulations Thank you for purchasing a Husqvarna Auto Mower. The Husqvarna Auto Mower is designed to offer user friendliness, high operating safety and a long service life. Auto Mower has been built to mow areas that contain slopes and confined passages as well as many trees and bushes. Using only a minimum of supervision and maintenance you can have a well-kept lawn throughout the season. This Operator’s Manual is a valuable document. By following its cont
Resumo do conteúdo contido na página número 4
SYMBOLS Symbols Symbols on the Auto Mower These symbols can be found on the lawn mower. Study them carefully so you understand their signifi- cance. IMPORTANT INFORMATION Read through the Operator’s Manual carefully and understand the content before using the Auto Mower. 1001-003 WARNING Auto Mower can be dangerous if used incorrectly. • The warnings and safety instructions in the Opera- tor’s Manual must be followed carefully for the mower to be used safely and efficiently. 1001-002 •
Resumo do conteúdo contido na página número 5
SYMBOLS Symbols in the Operator’s Manual These symbols can be found in the Operator’s Manual. Study them carefully so you understand their signifi- cance. • Inspection and/or maintenance should be carried out with the main switch set to ”OFF”. OFF 3012-288 • Always wear protective gloves when working with the mower’s underframe. 3012-272 • Never use a high-pressure washer or even running water to clean the Auto Mower. 3012-271 • The warning box warns of the risk of personal WARNIN
Resumo do conteúdo contido na página número 6
SAFETY INSTRUCTIONS Safety Instructions Use • Read through the Operator’s Manual carefully and understand the content before using the Auto Mower. 1001-003 • Check that there are no stones, branches, tools, toys or other objects on the lawn that can damage the blades and cause the mower to stop. 3012-275 • Start the Auto Mower according to the instructions. When the main switch is in the ”ON” position; make sure you keep your hands and feet away from the rotating blades. Never put y
Resumo do conteúdo contido na página número 7
SAFETY INSTRUCTIONS Transport The original packaging should be used when transport- ing the Auto Mower over long distances. To safely move from or within the working area: 1. Press the STOP button to stop the mower. If the stop protection, (see page 36) used as to prevent theft, has been activated enter the first number of the PIN-code. You select the four digit PIN code when you start the mower for the first time, see page 25. 3012-247 2. Switch off the main switch if the mower is to b
Resumo do conteúdo contido na página número 8
PRESENTATION Presentation Congratulations on your choice of an exceptionally high quality product. To get the best from your Auto Mower requires knowl- edge of its function. This chapter contains information you should be aware of when planning the installation. Installation of the Husqvarna Auto Mower includes four main components: Auto Mower, an automatic lawn mower that mows the lawn by moving in essentially an irregular pattern. The mower is powered by a maintenance free
Resumo do conteúdo contido na página número 9
PRESENTATION Function Auto Mower Working method The Auto Mower automatically mows the lawn. It con- tinuously combines mowing and charging. When the Auto Mower works on a lawn, it simulta- neously stores information about how the garden is shaped. The charging station sends out a signal that the Auto Mower can sense at a distance of 6 - 8 metres. The mower starts to seek out the charging station when the capacity of the battery becomes too low. The Auto Mower does not mow when it is
Resumo do conteúdo contido na página número 10
PRESENTATION The STOP button on the top of Auto Mower is mainly used to stop the mower when it’s running. When the STOP button is pressed a cover opens, behind which there is a control panel. The STOP button remains depressed until the cover is closed again. This acts as start inhibitor. 3012-247 The control panel on the top of the Auto Mower is where you manage all the mower settings. The main switch is also located on the control panel. Open the control panel cover by pressing do
Resumo do conteúdo contido na página número 11
PRESENTATION Movement pattern The mower’s movement pattern is irregular and is determined by the Auto Mower itself. A movement pat- tern is never repeated. This mowing system means the lawn is mown equally without any mowing lines. 3012-276 If the Auto Mower enters an area where it senses the grass is longer than earlier, it can change the move- ment pattern. It can then mow in a square pattern to cover the area of longer grass more systematically. Thereafter the mower returns t
Resumo do conteúdo contido na página número 12
INSTALLATION Installation This chapter describes how you install the Auto Mower. Before starting the installation read the previous chap- ter ”Presentation” on page 9 to page 12. The installation should be carried out according to the following steps: A. Preparations. B. Planning the installation C. Placing the charging station. D. Charging the battery. E. Laying the boundary wire. F. Connecting the boundary wire. G. Checking the installation H. Linking the Auto Mower to the charging
Resumo do conteúdo contido na página número 13
INSTALLATION Auto Mower, what is what? 2 6 6 5 9 7 4 3 1 8 13 12 10 11 15 14 17 16 18 19 20 22 21 3012-224 The numbers in the picture corresponds to: 1. Charging strip 12. Skid plate 2. Cutting height adjustment cover 13. Blade disc 3. Front wheel 14. Charging station 4. Drive wheel 15. LED for operation check of the boundary wire 5. Body 16. Boundary wire 6. Stop button 17. Transformer with power cord 7. Keypad 18. Low voltage cable 8. Display 19. Staples 9. Main switch 20. Boundary wi
Resumo do conteúdo contido na página número 14
INSTALLATION B. Planning the installation Charging station First and foremost the charging station should be posi- tioned: • Centrally in the main area, along the outer edge and with a large free area in front of the station. 3012-233 • In the shadow. The battery is spared if it charged in the low possible ambient temperature. • On relatively level ground. The height difference must not differ more than 10 cm between the front and rear of the charging station. Max 10 cm Max 10 cm 301
Resumo do conteúdo contido na página número 15
INSTALLATION Plan the position of the charging station according to the shape of your garden. The Auto Mower can be set for one of three basic gar- den shapes (see page 34). The Auto Mower works differently depending on the garden shape the mower has been set to. The available garden shapes are: open, complex 1 and complex 2. The following pictures are examples of the different garden shapes. The pictures are also good examples of appropriate charging station placement. • The open sha
Resumo do conteúdo contido na página número 16
INSTALLATION • Complex 2 is a large lawn area with many obstacles and passages. 3012-294 3012-295 2 2 Example of complex 2 garden shape. Lawn area 1500 m respective 800 m Do not put the charging station in a corner or pocket in the working area. 3012-235 If the garden consists of two large lawns joined by a passage, it may be difficult for the Auto Mower to find the entrance to the passage. Making it difficult to work efficiently in both areas. One way to make the mower effectively reach
Resumo do conteúdo contido na página número 17
INSTALLATION Boundary wire For a successful installation the placement of the boundary wire should be planned carefully. Planning is simplified if you make a sketch of the working area, including all obstacles. Draw how the boundary wire should be routed on the sketch. The boundary wire should be laid so it: • Forms a loop around the working area for the Auto Mower. Only Husqvarna boundary wire ought to be used. This is tinned and has a high quality insulation to withstand the dampne
Resumo do conteúdo contido na página número 18
INSTALLATION Remember the following with regard to the working area boundaries: • If a high obstacle, for example a wall or fence, bor- ders the working area, the boundary wire should be laid 35 cm from the obstacle. This will prevent the Auto Mower from colliding with the obstacle and reduce body wear. 35 cm 3012-229 • If the working area borders against, for example, pools of water the boundary wire should be supple- mented with a fence or the like. The height must then be at least
Resumo do conteúdo contido na página número 19
INSTALLATION Remeber the following with regard to the working area boundaries: • The Auto Mower can mow areas with a gradient of up to 1: 3 (33 cm/m) inside the working area. Areas that slope more must be demarcated by the bound- ary wire. If any part of the working area’s outer edge has a gradient of 1: 5 (20 cm/m) or more, the wire should be laid inside where the slope starts. The Auto Mower may find it difficult to turn at the loop where the ground slopes heavily. • Use the boundary
Resumo do conteúdo contido na página número 20
INSTALLATION • In order for the loop system to work well, the wires in passages where the Auto Mower is to run Secondary area through must not lie too close together. A passage should be at least 2 metres wide so the Main area Auto Mower can find it and make its way through it. The minimum spacing between the wires in a pas- sage is 130 cm. 2m 3012-232 The transition between a large area and a passage should be, if possible, designed like a ”funnel”, with rounded corners, to make it easier
