Resumo do conteúdo contido na página número 1
40PERATOR'S A MANUAL
Front Loader
J
Model FL5540KO
for Honda H5518A4
Multi-purpose Tractor I
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
CONTENTS TOPIC PAGE 1 .GENERAL ................................................................................................... 1 2 . INTRODUCTION ........................................................................................................ 3 Front loader safety ........................................................................................... 4 Maintenance safety ............................................................................................ 7 Safety lab
Resumo do conteúdo contido na página número 4
~ INTRODUCTION INTRODUCTION The purpose of this manual is to instruct you in maintaining and operating your HTA Front Loader. Read it carefully; it furnishes information and instructions that will help you achieve years of dependable performance. Some information may be general in nature due to unknown and varying conditions. However, through experience and these instructions, you should be able to develop operating procedures suitable to your particular situation. "Right" and "Left" as
Resumo do conteúdo contido na página número 5
FRONT LOADER SAFETY FRONT LOADER SAFETY Operating the tractor and front loader requires special efforts on your part to ensure your safety and the safety of others. Know these requirements before you operate the tractor or front loader. SAFE OPERATING RULES Severe personal injury or equipment damage may result if the operating instructions on ( pages 25 thru 30 ) are not followed. Always make pre-operation checks ( page 25 ) before you start the engine. You may prevent an accident or eq
Resumo do conteúdo contido na página número 6
Resumo do conteúdo contido na página número 7
FRONT LOADER SAFETY Never operate the tractor or front loader when visibility is diminished by darkness or by bad weather; your ability to see obstacles will become impaired. Avoid loose fill, rocks and holes. They may cause vehicle instability or cause the vehicle to overturn. The front loader is intended for relatively flat terrain useage. Avoid overhead wires and obstacles when the front loader is in the raised position. Contacting electric wires can cause electrocution. Allow for the
Resumo do conteúdo contido na página número 8
MAINTENANCE SAFETY MAINTENANCE SAFETY Maintenance of the tractor and front loader requires special efforts on your part to ensure your safety and the safety of others. Know these requirements before perfoming maintenance on the tractor or front loader. Before performing maintenance/inspections,read the instructions thoroughly. Before cleaning, inspecting or servicing the loader be sure to; - lower the front loader bucket flat to the ground. - move the front PTO to the off position - sto
Resumo do conteúdo contido na página número 9
SAFETY LABEL LOCATIONS SAFETY LABEL LOCATIONS Read these SAFETY LABELS before you operate the front loader. IMPROPER SERVICING CAN CAUSE SERIOUS INJURY OR DEATH TRACTOR TIP-OVER CAN 0 Before servicing or adjustment CAUSE SERIOUS INJURY lower loader to the ground and OR DEATH shut off engine. Rolleve hydraulic pressure before Add recommended disconnecting oil lines. • wheel ballast and/or counterweights for stability. Drive and turn tractor at slow speed. Place loader low when tr
Resumo do conteúdo contido na página número 10
PACKAGING INVENTORY PACKAGING INVENTORY 12 Required ............................................................................................................................................. 37.5 Ibs. each I 3 j 1 WEIGHTS ................. .................................................................... ................................ I SECURED TO CRATE BOTTOM ................~....,..~.....................~...~..~~..............~...~...........................................
Resumo do conteúdo contido na página número 11
TRACTOR PREPARATION - HARDWARE BAG CONTENTS 2 7/16"—14 hex nut 2 7/16" lockwasher QNT'Y DESCRIPTION 4 1/2"—13 hex nut 5 7/16" lynchpin 6 1/2" flat washer 2 10mm x 30mm hex hd capscrew 4 1/2" lock washer 2 12mm x 25mm hex hd capscrew 4 5/16"—18 x 1" hex hd capscrews 2 1/2-13x11/2" hex hd capscrew 4 5/16" lockwasher 16 #11 clip pin 2 7/16" flatwasher 12 3/4 x 11/4 x 10 ga. machine bushing 2 5/16"—18 13/4" hex hd capscrew 2 1/2-13x13/4" hex hd capscrew 2 5/16" flatwasher 2 3/8" fl
Resumo do conteúdo contido na página número 12
LOADER SPECIFICATIONS LOADER SPECIFICATIONS A- - LOADER SPECIFICATIONS ITEM ........................ ........ FL5540 Rated Lift Capacity ................ ........ 400lb (180kg) Bucket Size (width) ................ ........ 42in (1050mm ) Hydraulic cylinder ................ ......... Double acting Counterweights .................. ......... Suit case type 37.5lb x 12 ........................... ........ (17.0kg x 12) Sub-frame ..................... ........ Frame mount type Hydraul
Resumo do conteúdo contido na página número 13
ASSEMBLY INFORMATION ASSEMBLY INFORMATION GENERAL Read assembly instructions completely prior to installing loader to familiarize yourself with all mounting and hydraulic system installation procedures. The loader operates from its self contained hydraulic system with the pump driven from the tractor front PTO. A pipe thread sealant must be used on all pipe threads. All hardware required for mounting loader is supplied. Loader mount component hardware should be left loose until all moun
Resumo do conteúdo contido na página número 14
FL5540 SUB-FRAME and COUNTERWEIGHT INSTALLATION/REMOVAL -- FL5540 SUB-FRAME and COUNTERWEIGHT INSTALLATION/REMOVAL 1. Remove the existing frame lower cover and replace with the new lower cover using existing mounting bolts and collar washers. Never operate the tractor without the lower cover. INSTALLATION INSTRUCTIONS 1. CLEAN THE CONTACT SURFACES BETWEEN BRACKET AND FRAME. NEW LOWER 2. MOUNT THE BRACKET BY INSTALLING THE (8) BOLTS FINGER TIGHT. 3. TIGHTEN UNDERSIDE MOUNTING BOLTS:
Resumo do conteúdo contido na página número 15
FL5540 SUB-FRAME and COUNTERWEIGHT INSTALLATlON/REMOVAL 3. Lay the sub-frame on a level, solid area. 4. Position the tractor in line with the sub-frame and tire guide on drive on plate, allowing a clearance of approximately 60mm (2.4in) between sub-frame and the inner wall of the left front tire. GUIDE SUB-FRAME 5. Drive the tractor the rear of the sub-frame, over the drive on plate keeping it parallel with the sub-frame. SUB-FRAME Page 14
Resumo do conteúdo contido na página número 16
FL5540 SUB-FRAME and COUNTERWEIGHT INSTALLATION/REMOVAL 6. Stop the tractor when the mast fixing pad comes even with the floor board of the tractor. 7. Using two people, lift the sub-frame and engage the pipe of sub-frame into the U-shaped channel of the bottom bracket. NOTE: Use two people to lift sub-frame.
Resumo do conteúdo contido na página número 17
FL5540 SUB-FRAME and COUNTERWEIGHT INSTALLATION/REMOVAL 8. Lift the front of the sub-frame and slip it into the channel of the lower cover. Insert two mounting pins (3/4 x 3.19in) from inside sub-frame through frame lower cover. Slip a 3/4in washer over each mounting pin and insert the clip pins through the holes. NOTE: Mounting pins have a flat side that must be pointing down. MOUNTING PIN FLAT SIDE DOWN 9. Insert two mounting pins (3/4 x 3.19in) from inside the bottom bracket throu
Resumo do conteúdo contido na página número 18
FL5540 SUB-FRAME and COUNTERWEIGHT INSTALLATlON/REMOVAL COUNTERWEIGHT BRACKET INSTALLATION LINCHPIN MOUNTING PINS - - FIXING PINS COUNTERWEIGHT BRACKET 10. Place the rear counterweight bracket on the rear of the sub-frame aligning the mounting holes of the bracket with those of the sub-frame. Insert two 1 x 3.5 inch mounting pins in the forward holes and one 1 x 12 inch mounting pin in rear lower hole. Secure with linchpins. 11. Install the twelve counterweights. Insert the coun
Resumo do conteúdo contido na página número 19
FRONT LOADER ASSEMBLY FRONT LOADER ASSEMBLY PUMP HY DRAULIC PUMP MOUNTING MOUNTING LEFT BRACKET PLATE 1. Pump mounting plate and pump drive joint are installed on pump. Ensure bolts and set screw are tight. Attach the pump brackets to the pump mounting plate using two each 5/16x2 inch bolts and 5/16" flatwashers. The right bracket is shorter than the left. Do not tighten the bolts at this time. - RIGHT BRACKET Apply a light coating of grease to tractor front PTO at this time. 2.
Resumo do conteúdo contido na página número 20
FRONT LOADER ASSEMBLY PRESSURE and SUCTION HYDRAULIC HOSE CONNECTION 4. Remove the pipe plug from the valve body and clean the threads and then install the pressure hose. Remove the plastic caps from the pump outlets. Use sealer on threads and screw the other end (swivel ESSURE HOSE connector end) into the threaded pipe fitting on the pump. Slide the suction hose (large hose) over the pipe end at the HOSE CLAM bottom of mastkeservoir and pipe end on the pump. Attach with hose clamps
