Manual do usuário Great Dane GDSZ52-22KHE

Resumo do conteúdo contido na página número 1

GDSZ48-14KA
GDSZ48-16BV
GDSZ52-16BV
GDSZ52-18BV
GDSZ52-22KHE
GDSZ61-22KHE
PATENTS PENDING JAN 1997
GREAT DANE POWER EQUIPMENT, INC.
FORM D01002-97
JEFFERSONVILLE, INDIANA 47130 U.S.A.

Resumo do conteúdo contido na página número 2

TABLE OF CONTENTS PAGE 2 Safety Guidelines Common Accidents you must avoid Safety Interlock System 3 Hydraulic Safety 3 Assembly of Machine Initial Adjustments Initial run-in 3 Operating Instructions Field Servicing & Adjustments 4 Tire Pressure Height of Cut Belt Tension Free Wheeling Hydro Air Bleeding Spindle Disassembly Battery Servicing 5 Recommended Maintenance Check List Initial Break-in

Resumo do conteúdo contido na página número 3

SAFETY GUIDELINES During Operation .Using the machine demands attention. COMMON ACCIDENTS YOU MUST AVOID To prevent loss of control: * Mow only in daylight or when there is .CONTACT WITH ROTATING BLADES .THROWN OBJECTS good lighting .OPERATING WITHOUT GUARDS IN PLACE * Watch for pot holes, rocks, and any .RUNNING OVER SOMEBODY hidden hazard .OVERTURNING ON STEEP SLOPES * Keep away from drop-offs, ditches, creeks, ponds and Memorize the above and do yourself a favor; read, re

Resumo do conteúdo contido na página número 4

.If wheels do not stop rotating when controls are.~ in neutral, adjust HYDRAULIC SAFETY the NEUTRAL stop wing bolts at the rear of the power unit, between the two hydro pumps. .All hydraulic system servicing should be done by a qualified .Engage cutter blade clutch. Be sure area is clear technician. of debris. Run blades for several minutes. .Relieve all pressure in the system before disconnecting any .Shut off engine and remove jack stands. hoses. Remove start key. .Keep body

Resumo do conteúdo contido na página número 5

.When oil starts to flow in a steady stream from disconnected SERVICING & ADJUSTMENTS open port on the pump, reconnect hose to pump. .Secure machine in a safe area, away from bystanders and TIRE PRESSURE facing a wall. Raise drive wheels off the ground and block .When mowing on relatively smooth ground, keep rear wheel caster wheels tire pressure low, such as 14 to 16 psi. When mowing on Run full forward speed for about a minute and rough ground, increase then reverse speed for

Resumo do conteúdo contido na página número 6

RECOMMENDED MAINTENANCE CHECK LIST DAILY 1. Check engine oil level 2. Remove and clean engine air filter 3. Blow clean engine blower screen and fins 4. Clean out debris under belt cover 5. Inspect all belts for damage 6. Sharpen and balance cutter blades WEEKLY (or every 40 hours} 1 .Change engine oil 2. Grease caster wheel bearings (2 places) 3. Grease caster wheel pivot bearings (2 places) 4. Scrape clean underside of cutter deck 5. Check belt tension 6. Check tire pressu

Resumo do conteúdo contido na página número 7

Resumo do conteúdo contido na página número 8

Resumo do conteúdo contido na página número 9

Resumo do conteúdo contido na página número 10

Resumo do conteúdo contido na página número 11

Resumo do conteúdo contido na página número 12

Resumo do conteúdo contido na página número 13

Resumo do conteúdo contido na página número 14

Resumo do conteúdo contido na página número 15

Resumo do conteúdo contido na página número 16

Resumo do conteúdo contido na página número 17

Resumo do conteúdo contido na página número 18

Resumo do conteúdo contido na página número 19

Resumo do conteúdo contido na página número 20