Resumo do conteúdo contido na página número 1
PTO
GRASS COLLECTION
SYSTEM
PEC PEC PEC PEC PECO O O O O
PPPPP
DESIGNED FOR:
MODEL 12031301, 12031302
GRAVELY 100 SERIES MOWERs
OPERATOR’S MANUAL
ASSEMBLY OPERATION MAINTENANCE
MANUAL PART#: Q0322 $4.00 REV: 0
Resumo do conteúdo contido na página número 2
PTO GRASS COLLECTION SYSTEM TABLE OF CONTENTS SECTION PAGE SECTION PAGE Safety - ------------------------------2 2-12 Attachment Of The Upper Hose -----------13 Safety Alert Symbols----------------------3 2-13 Attachment Of The Lower Hose To The Blower Warranty -----------------------------4 Cone - - ------------------------------13 I INTRODUCTION AND DESCRIPTION - - ------------5 2-14 Attachment Of The Lower Hose To The Boot---13 1-1 Introduction - ------------------------5 2-15 Front Weight As
Resumo do conteúdo contido na página número 3
SAFETY WARNING! NEVER operate the unit unless the discharge guard and either the deflector assembly or the vacuum collector adapter are fastened securely in place. WARNING! Do not work around the mower deck boot or the blower area until you are certain that the mower blades and the blower impeller have stopped rotating. WARNING! To avoid serious injury, perform maintenance on the vacuum collector; ONLY AFTER STOPPING THE MOWER’S ENGINE AND WAITING FOR ALL MOVING PARTS TO COME TO A COMPLETE STOP.
Resumo do conteúdo contido na página número 4
PECO LIMITED WARRANTY FOR NEW PRODUCTS A. WHAT IS WARRANTED? PECO extends the following warranties to the original purchaser of each new PECO consumer product subject to the following limitations: 1. PRODUCT WARRANTY: Any part of any consumer product, which is defective in material or workmanship as delivered to the purchaser will be repaired or replaced, as PECO elects, without charge for parts or labor, if the defect appears within 12 months from the date of delivery of the product to the orig
Resumo do conteúdo contido na página número 5
SECTION I INTRODUCTION AND DESCRIPTION 1-1 Introduction Section II INSTALLATION FOR USE We are pleased to have you as a PECO customer. Your collection system has been designed to give you a low 2-1 Preparation Of Mower maintenance, simple, and effective way to collect the grass clippings from your mower. This manual is Carefully dismantle shipping box from around the provided to give you the necessary instructions to components. Cut retaining straps and separate the properly mount and operate th
Resumo do conteúdo contido na página número 6
. 2-2 Attaching Muffler Guard Figure 4. Locate the two exhaust diverters (P#J0251 w/ 1-1/4” ID, Right P#J0250 w/ 1-3/8” ID) and clamp kit P#(X1046) provided in the hardware bag. Fasten the correct size exhaust deflector onto the mower’s exhaust and aim the exhaust as shown in Figure 3. Next, fasten the exhaust diverter by using the clamp kit. Left Rear Of Mower Figure 3. Mower’s Exhaust 3 Existing Bolts Here NOTE: Right and left views are as seen from drivers perspective. Figure 5. Left Frame Mo
Resumo do conteúdo contido na página número 7
2-4 Safety Interlock Harness Connection Figure 9. The safety interlock harness is located inside of the right PTO arm assembly (Figure 7). To install the harness to the mower, lift the hood of the mower for engine compartment access. Route the harness as shown towards the parking brake switch bracket on the mower (Figure 8). Fasten the harness to the mower’s rear frame by using (1) zip tie P#(J0245) to prevent the harness from rubbing the mower’s tire. Next, remove the (2) bolts (Figure 9) from
Resumo do conteúdo contido na página número 8
Figure 11. Exploded View Of The (2) K1144 - 5/16”-18 x 1” A0549 - Bagger Assembly CARRIAGE BOLT (6) K1142 - 5/16”-18 x 3/4” CARRIAGE BOLT (4) K1010 - 1/4”-20 x 5/8” CARRIAGE BOLT (1) V0002 - PLASTIC TOP (2) K1126 - 1/4”-20 (1 LEFT, 1 RIGHT) FLANGE NUT B0237 - PIVOT BRACKET (2) K0037 - 1/4” FLAT WASHER (1) V1054 - INLET (1) C0048 - LATCH MOUNT BRACKET (2) K1025 - 1/4”-20 (1) B8002 - PLASTIC x 1” CARRIAGE SCREEN BOLT (2) J4005 - FLEXIBLE (2) C0051 - LONG DRAW LATCH SCREEN MOUNT STRIP (2) C0047 - P
Resumo do conteúdo contido na página número 9
2 Exploded Parts View 1 3 Figure 12. 4 Exploded View Of The Blower Assembly 5 2 6 7 9 12 11 13 8 10 24 21 33 32 Figure 13. 38 Exploded View Of The A0506 - PTO Assembly 22 23 14 28 17 19 37 16 34 18 15 25 35 26 36 20 31 30 29 27 40 39 41 9
Resumo do conteúdo contido na página número 10
Parts View 46 55 54 42 47 56 44 57 53 48 50 58 52 43 45 51 49 Item Part No. Qty. Description Item Part No. Qty. Description 1 ---- E6009- -----1 ---- Blower Cone 8” 31 - - - K0348- -----1 ----3/8”-16 x 2” HHCS 2 ----K1159- -----2 ---- 5/16”-18 x 2” HHCS 32 - - - K0086- -----1 ----1/8”x 2-3/8” Hair Pin 3 ---- A0914- -----1 ----4 Blade Impeller Clip Assembly 33 - - - B1755- -----1 ---- Blower Pivot Rod 4 ----K1193- -----4 ----3/8”-16 x 1-1/2” HHCS 34 - - - K0130- -----1 ---- 3/32” x 1-5/8” Hair Pi
Resumo do conteúdo contido na página número 11
P#(K0326) and pull the “L” end of the rod out of its hole 2-5 Belt Installation in the cam assembly. The tension rod may then be screwed out to tighten the belt or screwed in to loosen Loosen the (2) bolts that secure the gear box assembly the belt. Replace the “L” end into the top hole in the cam P#(A0429) to the PTO mount plate (Figure 14). Loosen and replace the hair pin clip. Adjust the cam stop bolt the adjustment bolt P#(K0348) until the gear box P#(K1159) to allow the cam to rotate slight
Resumo do conteúdo contido na página número 12
2-10 Attachment Of The Boot To The 2-8 Attachment Of Upper Frame Mower Deck Assembly To The Lower Frame NOTE: During this step, it is suggested that two Mounting The Boot Hanger Remove the mower’s deflector shield mount (Figure 20). people install the top frame to the lower frame. Using two people to raise the top frame, lift the top frame Position the notch towards the front of unit and place the above the lower frame making sure the bag frames are boot hanger P#(B0117) in-between the deflector
Resumo do conteúdo contido na página número 13
2-11 Adjustment Of The Lengths Of 2-13 Attachment Of The Lower Hose Hoses To The Blower Cone The hoses in steps 2-12 and 2-13 must be cut to fit your Fasten the blower cone P#(E6009) to the blower machine. Follow steps 2-12 and 2-13. Do not cut the housing by using (2) 5/16”-18 x 2-1/2” HHCS P#(K0125) hoses until you have tried to fit them on your machine. and (2) 5/16”-18 jam nuts P#(K0120). Slide a 7”-8” hose Remember that the hoses have to be long enough to clamp P#(J6006) over both ends of t
Resumo do conteúdo contido na página número 14
Figure 24. 2-16 Installation/Removal Of Plastic Top Collection Bags To install the bag onto the bag ring, first make sure the bag ring end caps are fastened to the bag ring. Place the seam openings of the bag onto the bag ring openings and turn the bag until the slot bracket in the bag ring is protruding from the opening in the bag (Figure 23). Do this for each of three bags. Install the completed assemblies onto the support frame and close the plastic top. Fasten both draw latches to hold the p
Resumo do conteúdo contido na página número 15
* Mow twice, at different height settings, (high, then low), 2-17 Final Checks if grass is extra tall. * Remember that horsepower requirements will vary with To check the operation of the safety interlock harness the mowing conditions such as type and height of turf perform the following: grass, moisture content, amount of leaves, whether the terrain is flat or hilly, etc. A. Start mower B. While seated in the operator’s seat, rotate the 3-3 Disengagement Of The Blower engagement handle of the c
Resumo do conteúdo contido na página número 16
3. Make sure all shields are in place and in good SECTION V condition. Repair or replace any missing or damaged shields. PARTS AND SERVICE 4. Perform lubrication per paragraph 4-2. 5. Listen for abnormal sounds, which might indicate loose parts, damaged bearings, or other damage. Correct any deficiency before continuing operation. 5-1 Parts And Service Information 6. With the engine off, engage the blower assembly. Check the belt tension and inspect the pulley belt for cracks or tears. PECO coll
Resumo do conteúdo contido na página número 17
SAFETY DECALS To promote safe operation, PECO supplies safety decals on all products manufactured. Damage can occur to safety decals either through shipment, use or reconditioning. Contact your local Service Center for replacement decals. Part #:R1051 Part #: R1054 Part #: R1057 Part #: R1065 Part #: R1050 Part #: R4037 Part #:R1083 Part #: R1052 Part #: R1090 17
Resumo do conteúdo contido na página número 18
18
Resumo do conteúdo contido na página número 19
NOTES 19
Resumo do conteúdo contido na página número 20
Turn any PECO Lawn Vac into a total lawn grooming tool with the PECO Wand Kit! With your PECO Wand Attachment you will double the ability of your PECO Lawn Vac. Using the same powerful vacuum/blower that makes your Lawn Vac work so well, you will be able to get to all those hard-to-reach places where you needed a rake or broom before. Contact PECO Today! PEC PEC PEC PEC PECO O O O O PPPPP P.O. BOX 1197 ARDEN, NORTH CAROLINA 28704 (800) 438-5823 OR (828) 684-1234 FAX: (828) 684-0858 EMAIL: peco@l
