Resumo do conteúdo contido na página número 1
OPERATOR’S
MANUAL
Turboless Twin Catcher
Turboless Twin Catcher
Mfg. No. Description
1695353 38” Turboless Twin Catcher
C CA AU UT TIIO ON N:: R Re ea ad d a an nd d
ffo ollllo ow w a allll iin ns sttr ru uc cttiio on ns s..
Manual Part No. 1734772
Revision 01
Rev. Date 05/2007
TP 100-4528-01-AT-SMAN
Resumo do conteúdo contido na página número 2
SAVE THESE INSTRUCTIONS READ THE MANUAL The operator’s manual contains important safety information you need to be aware of BEFORE you operate your unit as well as DURING operation. Safe operating techniques, an explanation of the product’s features and controls, and maintenance information is included to help you get the most out of your equipment investment. Failure to obey the safety rules could result in loss of control of the unit, sever personal injury or death to you, or bystanders, or da
Resumo do conteúdo contido na página número 3
Normal Removal Operatror Safety Assembly & Installation Table of Contents Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Mowing with the Catcher. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Resumo do conteúdo contido na página número 4
GENERAL WARNINGS • Know the unit’s controls and how to stop quickly. periodically for tears, holes, or weak spots and READ THE OPERATOR’S MANUALS. replace with a new bag that meets manufacturer’s � Read and obey all safety decals. durability standards. � Only allow responsible adults, who are familiar with � If the mower stalls or the collector chute plugs: the instructions, to operate the unit. 1. Disengage the PTO; � Disengage the PTO. Shut off the engine and wait 2. Stop the engine and remove
Resumo do conteúdo contido na página número 5
Safety Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag is very important. For this reason, BEFORE YOU BEGIN MOWING you should make certain the underside of the mower and the underside of the catcher l
Resumo do conteúdo contido na página número 6
4 Notes
Resumo do conteúdo contido na página número 7
Assembly Assembly INSTALL MOUNTING PLATES - A B C BROADMOOR / 1600 / 2600 / LT SERIES D Install Plates & Spacers 1. Mount the side brackets (C, Figure 1) to both sides of the frame using the holes shown. Secure with one 3/8-16 x 1 capscrew (D), 3/8 lockwasher (B), and 3/8-16 nut (A) per side. Figure 1. Install Side Brackets 2. Install the rear spacers (C, Figure 2). Secure with A. Nut, 3/8-16 two 1/2-13 x 2-1/2 capscrews (E), washers (D), B. Lockwasher, 3/8 spacers (C), and 1/2-13 nylock nuts (A
Resumo do conteúdo contido na página número 8
C B E A F A. Baffle (New) B. Spacer (New) C. Carriage Bolts, 5/16-18 x 2 (New) D. Locknuts, WHIZ Lock, D 5/16-18 (New) G E. Carriage Bolt, 5/16-18 x 5/8 (New) F. Wing Nut Assembly, Large, 5/16-18 (New) H G. Locknut, Center Lock, 5/16-18 (New) I J D H. Grass Shield (Existing) I. Blade, High Lift (New) K J. Hex Washer (Existing) L K. Washer (Existing) Torque Capscrew to L. Capscrew, 45-55 ft. lbs. (61-75 Nm) 7/16-14 x 1-1/4 (Existing) Figure 3. Baffle Assembly Install Baffle and Blade Note: Unit
Resumo do conteúdo contido na página número 9
Assembly Install Lower Chute Components D INSTALL BRACKET AND PIN ON LOWER CHUTE 1. Secure the puck (C, Figure 6) to lower chute (A) C using 5/16-18 x 3/4 capscrew (D) and 5/16-18 locknut (E). A 2. Install bracket (F) and deflector prop (G) to lower G chute (A) using 5/16-18 x 3/4 capscrews (D) and E 5/16-18 locknuts (E). F F D Figure 6. Install Pin and Bracket A. Lower Chute B. Locknut, 1/4-20 C. Puck, Metal D. Capscrews, Thin Head, 5/16-18 x 3/4 E. Locknuts, 5/16-18 F. Bracket G. Defflector
Resumo do conteúdo contido na página número 10
INSTALL BAG AND COVER SUPPORT INSTALL COVER ASSEMBLY 1. Install the bag and cover support (B, Figure 7) to 1. Attach cover assembly (B, Figure 9) to bag upright support (A) using reinforcement plate (C) support bracket (A) using hinge pivots (E). Secure and 3/8-16 x 1 capscrews (D) and 3/8-16 locknuts cover using cover hinge pins (C) and hair pins (D) (E) as shown. as shown. B B E C D A D E A C D C E Figure 7. Install Bag and Cover Support Figure 9. Install Cover Assembly A. Upright Support A.
Resumo do conteúdo contido na página número 11
Assembly INSTALL COLLECTOR BAGS INSTALL LOWER DISCHARGE CHUTE 1. Raise the cover (A, Figure 10). 1. Lift discharge deflector up (E, Figure 11). 2. Attach collector bags (B) using grass bag hanger 2. Slide the notch of bracket (G) on to deflector hinge (C) to bag hanger post (D). rod (F). 3. Secure the front of lower chute (A) to carriage bolt A (D) using wing nut (B) and locknut (C). Note: Locknut (C) is intended to keep wing nut (B) permanently on carriage bolt (D). C A D E G F B C Figure 10. I
Resumo do conteúdo contido na página número 12
F B C E A B A E D D Figure 12. Install Discharge Tube A. Boot B. Discharge Tube C. Seal D. Puck, Metal E. Wire Form F. Slits INSTALL DISCHARGE TUBE 1.Slide discharge tube (B, Figure 12) into seal (C). It may be necessary to lengthen several slits (F) in order for tube (A) to fit into seal (B) 2. Attach the discharge tube (B and Inset) to boot (A) and secure the tube by moving wire form (E) down over metal puck (D). 10 Assembly
Resumo do conteúdo contido na página número 13
Normal Removal & Installation Normal Removal & Installation of A Lower Discharge Chute Note: See previous pages for more detailed E G installation and operation instructions if necessary. 1. Lift discharge deflector up (E, Figure 13). F 2. Slide the notch of bracket (G) on to deflector hinge rod (F). B 3. Secure the front of lower chute (A) to carriage bolt C (D) using wing nut (B) and locknut (C). D Note: Locknut (C) is intended to keep wing nut (B) permanently on carriage bolt (D). Figure 13.
Resumo do conteúdo contido na página número 14
E F K G D C D A B C L H J I L A. Hitch Support G. Discharge Tube Assembly H. Wire Form B. Cover I. Puck C. Pin J. Boot D. Hair Pins K. Seal E. Bag L. Frame Spacers F. Grass Bag Hanger Figure 14. Normal Installation & Removal 3.Remove and empty bags (E, Figure 10). WARNING 4. Lift discharge deflector up (E, Figure 13). OPERATION WITHOUT BAGGER 5. Loosen (do not remove) wing nut (B) and lock nut For operation without bagger, the mower (C). deflector MUST be properly installed in the down position
Resumo do conteúdo contido na página número 15
Normal Removal & Installation 13
Resumo do conteúdo contido na página número 16
MANUFACTURING, INC. PRODUCTS 500 N Spring Street / PO Box 997 535 Macon Street Port Washington, WI 53074-0997 McDonough, GA 30253 www.SimplicityMfg.com www.Snapper.com 500 N Spring Street / PO Box 997 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 Port Washington, WI 53074-0997 AGCOLawn.com www.MasseyLawn.com Briggs & Stratton Yard Power Products Group Copyright © 2007 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved
