Manual do usuário Schumacher SE-4022 SE-6030

Resumo do conteúdo contido na página número 1

Battery
SE-2001, SE-4020, SE-4022
SE-6030, SE-8050
Charger
Models:
Owner's Manual
–Save–
Important Safety Instructions
Read Rules for Safe Operation and Instructions Carefully
Working in vicinity of a lead-acid battery is dangerous. Batteries generate explosive gases during normal
battery operation. For this reason, it is of utmost importance that each time before using your charger, you
read this manual and follow the instructions exactly.
WARNING: Handling the cord on this product or cords ass

Resumo do conteúdo contido na página número 2

B. PERSONAL PRECAUTIONS AND SAFETY 1. WARNING: Wear complete eye protection and clothing necklaces, and watches when working with a lead-acid protection, when working with lead-acid batteries. battery. A lead-acid battery can produce a short-circuit 2. Make sure someone is within range of your voice or close current high enough to weld a ring (or the like) to metal, enough to come to your aid when you work with or near a causing a severe burn. 6. Take care not to drop a metal tool or other metal

Resumo do conteúdo contido na página número 3

F. OPERATING INSTRUCTIONS: CHARGING BATTERY IN VEHICLE When charging battery in the vehicle, take care to determine the battery type and which post is grounded. To reduce risk of a spark near battery, follow these steps when battery is installed in vehicle. WARNING: A spark near battery may cause battery explosion. WARNING: Do not connect clip to carburetor, fuel lines, or sheet-metal body 1. Position AC power cord and DC charging cords to reduce parts. NOTE: Attach clips to battery post and twi

Resumo do conteúdo contido na página número 4

H. OUTPUT SELECTOR CONTROLS VOLT/RATE SELECTOR CHARGE TIME/MINUTES CHARGE RATE CHARGE TIME/MINUTES 6 VOLT BATTERY SE 2001 60 AMP/200 AMP SE 8050 TEST START 200 amp start 2 amp 6 VOLT 30 AMP 12 VOLT #2 #1 30 AMP Voltmeter LOAD ON Ammeter 6 VOLT 40 amp 40 amp OFF 200 amp 12 VOLT 60 AMP Ammeter 12 VOLT 300 AMP 12 VOLT START VOLT/RATE SELECTOR CHARGE TIME/MINUTES Rotary switch - Use the rotary

Resumo do conteúdo contido na página número 5

I. ENGINE START 1. Set charge rate switch and timer to OFF positions. Do not try to engine start a vehicle without a battery in it. You 2. With the charger unplugged from the AC outlet, connect the may damage the vehicle’s system. If the engine spins, but doesn’t charger to the battery following instructions given in section start after several starting attempts, there is a problem with the F. engine of the vehicle other than its starting system. STOP crank- 3. Plug the charger AC power cord int

Resumo do conteúdo contido na página número 6

L. ASSEMBLY INSTRUCTIONS Wheel Charger Assembly Instructions: (Instrucciones De Armado) NOTE: Charger must be assembled before operating (Ante de la operación la unidad debe estar armada) Parts (Piezas) Tools necessary (Herramientas Necesarias) (4) 10-32 screws (tornillos de corte rosca 10-32) 5/16" wrench (Llave de 5/16") HUBS MUST 3/8" wrench (Llave de 3/8") FACE IN (2) 1/4-20 screws (tornillo de corte rosca 1/4-20) Fig. B (2) wheels(ruedas) Hammer (Martillo) Fig. C Screwdriver (Destornillador

Resumo do conteúdo contido na página número 7

A. SEGURIDAD GENERAL DE ACUMULADORES 5. Quítese todos los artículos metálicos, tales como anillos, brazaletes, collares y relojes, al trabajar con un acumulador de ácido de plomo. 1. Antes de usar su cargador de acumuladores, lea todas las instrucciones Un acumulador de ácido de plomo puede producir un cortocircuito y precauciones impresas en: suficientemente fuerte para soldar un anillo (u otro objeto) a otro metal,  el cargador de acumuladores causando así una quemada severa.  el acumulador

Resumo do conteúdo contido na página número 8

E. INSTRUCCIONES DE FUNCIONAMIENTO: CARGA DE UN (NEGRA) del cargador al extremo libre del cable. ADVERTENCIA: ACUMULADOR EN UN VEHICULO No se quede de frente hacia el acumulador al hacer la conexión final. Al cargar un acumulador en un vehículo, determine cuidadosamente Gire la pinza de ida y vuelta para hacer un buen contacto. el tipo del acumulador y cuál es el terminal de tierra. Para reducir el 5. Haga todos los ajustes antes de aplicar la corriente alterna al cargador. riesgo de chispas cer