Resumo do conteúdo contido na página número 1
MULTI-BATTERY CHARGING STATION
Model 92775
OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
®
©
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical quest
Resumo do conteúdo contido na página número 2
PRODUCT SPECIFICATIONS Item Description Electrical Input Power: 120 VAC / 60 Hz. Requirements Power Plug Type: 3 Prong, Polarized. Polarity: Reverse Polarity w/Short Circuit & Overload Protection. Output Power: Can Charge 12 VDC Batteries @ 0.25, 0.50, and 0.90 AMPs. Charger Clamp 2-1/2” Wide x 3-1/4” Long x 5/8” Thick w/17” Cord. Dimensions Battery Capacity Can Charge Up To 6 Batteries At One Time. Charger Dimensions 11-3/8” Long x 15-1/2” Wide x 8-1/2” High. Stand Dimensions 18-1/4” Long x
Resumo do conteúdo contido na página número 3
WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power equipment in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power equipment creates sparks which may ignite flammables. 3. Keep bystanders, children, and visitors away while operating power equip- ment. Distractions can cause you to lose control. Protect others in the work area. PERSONAL SAFETY 1. Stay alert. Watch what you are
Resumo do conteúdo contido na página número 4
2. Do not use the Charger if any of the Control Panel components do not work properly. Any equipment with a faulty Control Panel is dangerous and must be replaced. 3. Before making any adjustments, changing accessories, or storing the Charger, make sure all Switches on its Control Panel are in their “OFF” positions. Such preventive safety measures reduce the risk of starting the equipment accidentally. 4. Store idle equipment out of reach of children and other untrained persons. Power equipme
Resumo do conteúdo contido na página número 5
GROUNDING WARNING! Improperly connecting the grounding wire can result in the risk of electric shock. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Do not modify the power cord plug provided with the tool. Never remove the grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet instal
Resumo do conteúdo contido na página número 6
EXTENSION CORDS 1. Grounded tools and equipment require a three wire extension cord. 2. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool and equipment damage. (See Figure B.) 3. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14 gauge cord can carry a higher current than a 1
Resumo do conteúdo contido na página número 7
SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Incorporated Volts V ~ Alternating Current Amperes A No Load no xxxx/min. Revolutions Per Minute (RPM) FIGURE C SPECIFIC SAFETY RULES 1. Maintain a safe working environment. Keep the work area well lit. Make sure there is adequate surrounding workspace. Always keep the work area free of obstructions, grease, oil, trash, and other debris. Do not use the Charger in areas near flammable chemicals, dusts, and va
Resumo do conteúdo contido na página número 8
7. Never leave the Charger unattended when any of its Switches on the Control Panel are left in their “ON” position. Make sure all Switches are in their “OFF” position before leaving. 8. Make sure to read and understand all instructions and safety precautions as outlined in the manufacturer’s manual for the battery that will be charged. 9. Never allow the Red and Black Charger Clamps to touch each other or the same metal object. 10. Always connect the Black Charger Clamp of the Charger to the
Resumo do conteúdo contido na página número 9
and water and rinse with lemon juice and vinegar. If the fluid comes into contact with the eyes, flush with water for several minutes and contact a doctor immediately. Never burn the battery, as it can explode in a fire. Do not charge a leaking battery. Contact local solid waste authorities for instructions on correct disposal or recycling of old batteries. 20. Performance of the Charger (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usag
Resumo do conteúdo contido na página número 10
1. Charging Current Selector (1): The Charging Current Selector is used for selecting a charging current of either 0.25 AMPs, 0.50 AMPs, or 0.90 AMPs depending upon the 12 volt battery that is to be charged. Use a digital voltmeter (not included) to determine the voltage of the battery. Check the battery manufacturer’s recommended charging current. Then, set the Charging Current Selector to the appropriate Amperage. (See Figure D.) 2. Power On (2): When illuminated, the Power On feature in
Resumo do conteúdo contido na página número 11
9. 3 AMP Fuse (9): The 3 AMP Fuse is located on the rear panel of the Battery Charger. In the event the Power On (2) feature on any of the six separate cir cuits does not illuminate, turn Power Switch(es) (6) to the “OFF” positions and unplug the Battery Charger from its electrical outlet. Temporarily remove the Fuse Cap. Pull out and remove the 3 AMP Fuse to check for a melted wire strand within the Fuse. If necessary, insert a new 3 AMP Fuse into the Fuse Holder. Then replace the Fuse Ca
Resumo do conteúdo contido na página número 12
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Before performing any inspection, maintenance, or cleaning procedures, make sure all Switches on the Control Panel are in their “OFF” positions and the Charger is disconnected from its electrical outlet. Such preventive safety measures reduce the risk of starting the equipment accidentally. 2. Before each use: Inspect the general condition of the Charger. Check for misalignment or binding of moving parts, cracked or broken parts, dam
