Manual do usuário Peerless Industries DS508

Resumo do conteúdo contido na página número 1

Installation and Assembly:
Model: DS508
Maximum Load Capacity:
200 lb (90.7 kg)
ISSUED: 03-05-09 SHEET #:125-9054-2 07-15-09
Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

Resumo do conteúdo contido na página número 2

IMPORTANT! Read instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US customers please call Peerless customer care at 1-800-865-21 12, for all international customers, please contact your local distributor . • This product should only be installe

Resumo do conteúdo contido na página número 3

Before you begin, make sure all parts shown are included with your product. Parts may appear slightly different than illustrated. A Parts List Description Qty. Part # A wall plate 1 145-1054 B adapter plate 1 145-1052 C #14 x 2.5" wood screw 4 5S1-015-C03 D concrete anchor 4 590-0097 E M8 x 15 mm socket pin screw 4 520-1068 F M4 x 12 mm phillips screw 4 504-9013 G M5 x 12 mm phillips screw 4 520-1027 H M6 x 12 mm phillips screw 4 520-1128 I M10 x 15 mm socket screw 4 520-9262 J #8 SAe flat was

Resumo do conteúdo contido na página número 4

Installation to Double Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • T ighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power . • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud. The

Resumo do conteúdo contido na página número 5

Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica- tions. It is suggested that a standard electric drill on slow setting is used to drill th

Resumo do conteúdo contido na página número 6

Installation to Metal Studs WARNING • Drywall must be 1/2" or thicker , and metal stud must be 24 gauge or thicker . • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components. • Make sure that togglers are anchored into the center of the studs. The use of an "edge to edge" stud finder is highly recommended. Using a stud finder , locate and mark the edges of the metal stud used in mounting this product. Use of an edge 1

Resumo do conteúdo contido na página número 7

Placement of Adhesive Strips Place adhesive strips (K) on the wall plate (A) in location that will allow the most contact with CPU. 2 Note: Placement of adhesive strips will vary depending on size of CPU as shown in figure 2.2 fig. 2.1 fig. 2.2 A Placement of adhesive Placement of adhesive strips (K) for smaller CPU's strips (K) for larger CPU's K Attach CPU to Wall Plate NOTE: Safety belt may need to be loosened to attach CPU to wall plate (A). 3 Press CPU against adhesive strips on wall

Resumo do conteúdo contido na página número 8

Attaching Adapter Plate to Screen fig. 4.1 Attaching adapter plate to screen with SCreeN 4 VESA hole pattern: Choose hole pattern and fasteners shown in detail 2 for B mounting screen with VESA mounting patterns. Hand thread screws (F, G or H) through washers (J or O) and adapter plate (B) into screen as shown in figure 4.1. Screw must make at least three full turns into the mounting hole and fit snug into place. Securely tighten screws. WARNING • If screws don't get three complete

Resumo do conteúdo contido na página número 9

Attaching Adapter Plate to W all Plate Thread two M8 x 15 mm screws (E) into bottom holes of wall plate (A) leaving 1/8" space between head of screw 5 and wall plate as shown in figure 5.1. guide hook slots of adapter plate ( B) onto screws (E), while supporting weight of screen, align top holes of wall plate and adapter bracket to the desired tilt angle and secure with two M8 x 15 mm screws (E). T ighten all screws securely . fig. 5.1 10° TILT 5° TILT fig. 5.2 NO TIL T A HOOK SLOTS E