Resumo do conteúdo contido na página número 1
VMAA18
(6901-100016 <04>)
Thank you for choosing the Sanus VMAA18 wall mount. The Sanus VMAA18 wall mount is
designed to support a monitor sized up to 50 in. (127cm) and weighing up to 59 kg (130
lbs). The mount is adjustable; it will tilt +5° to -15°, swivel to ±90°, and roll ±6.°
WARNING
This product contains small items that could be a choking hazard if swallowed.
Keep these items away from young children!
CAUTION
This product is designed for use in wood stud walls only! The wall must be
Resumo do conteúdo contido na página número 2
3/16 in. Supplied Parts and Hardware Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the item to your dealer; contact Sanus Customer Service. Never use damaged parts! [03] x 2 [05] x 4 [01] x 1 [02] x 1 [04] x 2 1/4-20 5/16-18 x 1 in. 5/16 in. [09] x 10 [10] x 1 [06] x 4 [07] x 4 [08] x 2 M6 x 12mm M8 x 16mm M5 x 12mm 5/16 x 2.5 in. M4 x 12mm [11] x 4 [12] x 4 [13] x 4 [14] x 4 [15] x 4 [16] x 2 001435.eps 001426.eps Lag
Resumo do conteúdo contido na página número 3
1: Attach Brackets to Monitor For Monitors with a Flat Back [11], [12], [13], [14] 4x [17], [18], [19], [20] [28], [29] 001427.eps FPM70-Flat and Curved Back Brackets 001429.eps FPM70-Brackets not level [03] For Monitors with a Curved Back or Obstruction [11], [12], 4x [13], [14] OPT [28] [17], [18], OPT [19], [20] [22], [23] [28], [29] [03] Use washer [28] with M4 or M5 001428.eps OPT hardware only. FPM70-Curved Back Hardware 001427.eps FPM70-Flat and Curved Back Brackets 001429.eps 69
Resumo do conteúdo contido na página número 4
2: Install Vise Assemblies [05] 4x [30] [07] [03] NOTE 001430.eps FPM70-Vise assemblies installed Do not overtighten the nut [07]. The vise assembly [05] must rotate freely around the carriage bolt [30]. 3: Install Arm Assembly to Monitor 001431.eps [31] FPM70-Detail, vise installation 2x [04] [03] 2x 001438.eps 001438.eps FPM70-Arm Attachment Detail 6x FPM70-Arm Attachment Detail [02] [04] [03] [05] NOTE Do not overtighten the fastener in the vise assemblies [05]. Tighten only enough to pre
Resumo do conteúdo contido na página número 5
001439.eps Attach Plate to Wall 001439.eps Attach Plate to Wall 4: Install Wall Plate 3/16 in. 001439.eps NOTE Attach Plate to Wall This product must only be used with wood studs spaced 30 - 40 cm (12 - 16 in.) on center. [01] NOTE Do not overtighten the lag bolts [15]. Tighten only until the washer [06] is pulled firmly against the wall plate [01]. Periodic maintenance may be required. [06] [15] 6901-100016 <04>
Resumo do conteúdo contido na página número 6
5: Attach Arm to Wall Plate [32] HEAVY! You will need assistance with this step. [02] [01] CAUTION Avoid potential injuries or property damage! Ensure the safety bolts [08] are secure. Periodic maintenance may be required. [08] 6901-100016 <04>
Resumo do conteúdo contido na página número 7
6: Install Preventer [32] Install the preventer [10] on the left side if you want the arm to fold to the left. Install OPT the preventer on the right side if you want the arm to fold to the right. OPT [10] [21] 7: Install Cable Management [16] [09] [16] NOTE Be sure to leave enough slack in the cables to allow the monitor to move freely. Use the cable ties [09] and wire clips [16] to secure the cables to the brackets [03] and arm [02]. [09] [03] 6901-100016 <04> 001454.eps FPM70-Cable Ma
Resumo do conteúdo contido na página número 8
001420.eps Arrows 001420.eps Arrows 8: Adjust Monitor Position [31] Adjust Level [A] 001449.eps FPM70-Back of Assembly Adjust Left / Right Swivel [B] [B] [C] CAUTION Avoid potential injuries or property damage! Remove the safety bracket [B] only to adjust the swivel tension nut [C]. Be sure to replace the safety bracket after adjusting the swivel tension nut. The hex hole in the safety bracket must seat over the swivel tension nut. 6901-100016 <04> 001451.eps 001451.eps FPM70-L FPM70-L eft /
Resumo do conteúdo contido na página número 9
001420.eps Arrows Adjust Up / Down Pitch NOTE Adjust the pitch tension by tightening or loosening the tension knobs [D]. [D] Extend or Retract Arm CAUTION [31] Avoid potential injuries or property damage! Do not remove the adjustment nut [E]; tighten or loosen only as necessary for easy arm adjustment. 001453.eps FPM70-Full Assembly 001450.eps FMP70-Up / Down Pitch [E] [E] 6901-100016 <04> 001452.eps FPM70-Extend / Retract Arm 001447.eps FMP70-Lower tab/locking fastener 001420.eps Arrows
Resumo do conteúdo contido na página número 10
Milestone AV Technologies, Inc. and its affiliated corporations and subsidiaries (collectively, “Milestone”), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
