Resumo do conteúdo contido na página número 1
,
(
(
(
!!"#$%&$$'!
Resumo do conteúdo contido na página número 2
Angle bracket Glass top Anglebracket Thinside Leftside Long rail Left front Back Rightside Glass shelf Steel bracket Base Thinside Glide (gray / black) Right front PART DESCRIPTION: PART NUMBER QTY 1 Base M20205A1PO 1 Left side M20206A1ZS 1 Right side M20207A1ZS 2 Thin side M20208A1ZS 1 Right front M20209A1ZS 1 Left front M20210A1ZS 1 Long rail M20211A1ZS 1 Back M20212A1PO 1 Glass top M20213A1PO 1 Glass shelf M20214A1PO 1 Steel bracket P816190 2 Angle bracket P816191A 4 Cable duct P840200 3 Gray
Resumo do conteúdo contido na página número 3
Bump-on P840022 x 18
Resumo do conteúdo contido na página número 4
B Front edge Glide (gray/black) Back edge x6 Base (underside) Fasten6 glides tothebaseas shown. Note that there are 3 gray and 3 black glides. Use gray glides at front of the base if the stand is going to be placed on a light colored floor. Use Black glides at the front if the stand is going to be placed on a dark colored floor. Left front panel Large wooden dowels x 4 Right front panel x6 Screw3 connector rods into holes in left and right front panels as indicated above. Press fit 2 large woode
Resumo do conteúdo contido na página número 5
Left side panel Right side panel Small wooden dowels x12 Press fit small wooden dowels into left and right sides as shown above. Right side panel Left side panel x12 Insert cams into large holes in left and right sides as shown. Make sure arrows on the cams point towards the corresponding cam holes along the edges of the panels.
Resumo do conteúdo contido na página número 6
Back x4 Screw4 connectorrods into holes indicated in back panel. Base x4 x2 Screw 4 connector rods into holes in the base as indicated above. Insert 2 cams into large holes in the base as shown above.
Resumo do conteúdo contido na página número 7
Left side panel Right side panel Cable duct Press fit the sides to the back as shown above. Turn the cams clockwise to tighten. Press fit 4 cable ducts into large holes in the back as shown. Assistance may be needed for this step. Press fit the sides and back assembly onto the base as shown. Turn the cams clockwise to tighten.
Resumo do conteúdo contido na página número 8
C x5 Fasten the back to the base as shown above. x2 D Long rail x2 Assistance may be needed for this step. Hold the long rail in between the sides as illustrated. Insert the black barrelnuts into the holes in the long rail. Ensure the holes in thesides are alignedwith theholes inthe longrail. Fasten the sides to the long railas shown.
Resumo do conteúdo contido na página número 9
Press fit the front panels to the sides and base as shown. Turn the cams clockwise to tighten. Adjusting screw x4 Thin side Slide thin sides down slots in front panels and back, ensuring silver surfaces face out. Screweach adjusting screwinto sides by half of it's visible threaded length, then once this is done, tighten all 4 Adjusting screws fully into sides.
Resumo do conteúdo contido na página número 10
Steel bracket Fit the long steel bracket into the rebate in the long railand in the grooves in the sides as shown above. Ensure the bracket is equally distanced from the sides on both ends. A x5 Once the bracket is adjusted in the sides, fasten it to the long rail using the screws shown above. It is important that you hold the long railagainst the steel bracket as you tighten the screws.
Resumo do conteúdo contido na página número 11
Bump-on(self adhesive) x18 Attach 18 bump-ons to top surface of the back, sides, front rails, and steel bracket where shown above. Assistance may be needed for this step. When placing the glass top on the unit, pay attention to the following tips: * Ensure painted side is facing down. * Back edge of the glass top must be flush with the back panel. * Glass top's overhang at the left side must match that of the right side. * Lift the glass when repositioning it, do not drag it as it could damage y
Resumo do conteúdo contido na página número 12
A x4 Fasten the angle brackets to the back as shown above. Note - the angle brackets are essentialfor the strength of the stand. Assistance will be needed for this step. x6 Insert 2 shelf pins into the bottom holes in the right side. Place a piece of polystyrene (from the pack) onto the base as shown above (Alternatively you could use a soft rag). Tilt the glass to one side and rest it on top of the polystyrene.Then carefully push the glass inside the cabinet and rest the right side on the shelf
