Resumo do conteúdo contido na página número 1
ESPAÑOL: PÁGINA 9
Instruction manual
FRANÇAIS: PAGE 17
Manual de
Instrucciones
1/2” Impact Wrench
Manuel d'instructions
Herramienta
Neumátiaca de Impacto,
de 1/2"
Clé à chocs de 1/2 po
MODEL PT502
MODELO
PT502
MODÈLE PT502
To learn more about Porter-Cable visit
our website at:
http://www.porter-cable.com
IMPORTANT
Para obtener más información sobre
Please make certain that the person who is
Porter-Cable, visite nuestro sitio web en:
to use this equipment carefully reads and
http://www.porter
Resumo do conteúdo contido na página número 2
SAFETY GUIDELINES - DEFINITIONS This manual contains indicates an imminently hazardous situation which, if not information that is avoided, will result in death or serious injury. important for you to know and indicates a potentially hazardous situation which, if not understand. This information re- avoided, could result in death or serious injury. lates to protecting YOUR SAFE- TY and PREVENTING indicates a potentially hazardous situation which, if not EQUIPMENT PROBLEMS. To avoided,may resu
Resumo do conteúdo contido na página número 3
HAZARD RISK OF LOSS OF HEARING WHAT COULD HAPPEN HOW TO PREVENT IT Long term exposure to noise produced from the opera- Always wear ANSI S3.19 hearing protection. tion of air tools can lead to permanent hearing loss. HAZARD RISK TO BREATHING INHALATION HAZARD WHAT COULD HAPPEN HOW TO PREVENT IT Abrasive tools, such as grinders, sanders, and cut-off Always wear MSHA/NIOSH approved, properly fitting tools generate dust and abrasive materials which can face mask or respirator when using suc
Resumo do conteúdo contido na página número 4
HAZARD RISK OF INJURY (continued) WHAT COULD HAPPEN HOW TO PREVENT IT Improperly maintained tools and accessories can cause Maintain the tool with care. serious injury. Keep a cutting tool sharp and clean. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control. There is a risk of bursting if the tool is damaged. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operati
Resumo do conteúdo contido na página número 5
SPECIFICATIONS Maximum Torque 500 ft./lbs Blows Per Minute 1,000 Maximum Working Pressure 90 PSI Air Inlet 1/4” NPT Recommended Hose Size 3/8” I.D. Air Consumption @ 90 PSI 4.2 SCFM ASSEMBLY Accessories Required IMPORTANT: Line pressure or hose inside diameter should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and fittings should have 1/4” NPT thread. OPERATION Operation Before each use: Drain water from air compressor tank
Resumo do conteúdo contido na página número 6
MAINTENANCE Lubrication Air tools require lubrication throughout the life of the tool. The air motor and bearing uses com- pressed air to power the tool. Because moisture in compressed air will rust the air motor, you must lubricate the motor daily. An inline oiler is recommended. To lubricate the air motor manually: Disconnect the tool from the air supply holding it so the air inlet faces up. Depress the trigger and place one to two drops of air tool oil in the air inlet Depressing the tri
Resumo do conteúdo contido na página número 7
REPAIR PARTS 39 11 9 13 43A 45 32 8 44 1A 48 49 19 21 29 (6) 2 Ref No. Part No. Description Qty 1a D25494 Handle Grip 1 2 u Throttle Valve Spring 1 8 u O-Ring 1 9 u Air Valve 1 11 u O-Ring 1 13 u O-Ring 1 19 + Trigger Pin 1 21 + Trigger 1 29 u Rotor Blade 6 32 u End Plate Gasket 1 39 u Hammer Case Gasket 1 43a u Standard Anvil 1 44 u Socket Retainer 1 45 u Retainer O-Ring 1 48 + / u Cap 1 49 + / u Screw 1 + Only available in Trigger Repair Kit D25489 u Only available in Tune-Up Kit D26759 NOTE
Resumo do conteúdo contido na página número 8
LIMITED WARRANTY PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this warranty are free from defects in material and workmanship. Products covered under this warranty include air compressors, air tools, service parts, pressure washers, and generators, which have the following warranty periods: 3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM. 2 YEARS - Limited warranty on oil-lubricated air compressor pumps.
