Manual do usuário Optoma Technology Panoview Graywolf II

Resumo do conteúdo contido na página número 1

Resumo do conteúdo contido na página número 2

NO.1 IMPORTANT SAFETY INSTRUCTIONS Basic safety precautions,including the following should always be followed. Close supervision is necessary when any motorized screen is used by or near children,do not leave motorized screen unattended while in use. Do not operate motorized screen with damaged cord or if the motorized screen has been dropped or damaged,until it has been examined by a qualified service technician. Position the cord so that it will not be tripped over,pulled or in conta

Resumo do conteúdo contido na página número 3

N0.2 To reduce the risk of electric shock,do not disassemble this appliance,only a qualifid service technician may service or repair motorized screen.Incorrect reassemble can cause electric shock when the motorized screen is used. Only use accessory attachment recommended by the manufacturer.Use of non-manufacturer recommended acces- sory attachments,may viod the screens warranty and release Panoview of all liability. Basic electrical safety precautions should always be observed. In the eve

Resumo do conteúdo contido na página número 4

NO.3 ELECTRIC CONNECTION Thank you for choosing Panoview screens. All screens have passed the strict quality inspection before delivery. Read this manual carefully to ensure proper usage. Important Attention: the installation of the screen, the electric wire connection, the setting of the limit switches must be made by a trained engineer only. SWITCH BOX PLUG SWITCH JACK 12V TRIGGER Motorized screen with IR remote control, switch control & 12v trigger port

Resumo do conteúdo contido na página número 5

N0.4 Technical data: Input Voltage: 110VAC/60HZ Output Voltage: 3A Fuse: 1A IR Remote Control Distance: ≤8m, ±15°Horizontal 12V Trigger Jack: OD3.4xID1.3 12V Trigger Signal: Voltage:7---11VAC or 8---16VDC, Current: ≥2mA IR Handset: 1pc Switch control: 1pc Unpack screen carefully, be sure screen is in good condition, and check that all accessories are included inside carton. Care in mounting and care in correct operation will mean a long and satisfactory life for your Panoview sc

Resumo do conteúdo contido na página número 6

NO.5 Remove two pulling locks on the bottom slat bar after the case has been installed. Install screen brackets onto ceiling or wall with appropriate hardware. Anchor screen onto bracket as shown in above figure below. MOUNT SCREEN TO WALL MOUNT SCREEN TO CEILING

Resumo do conteúdo contido na página número 7

N0.6 ELECTRIC CONNECTION Internal wiring has been completed at the factory.No addi- tional wiring is necessary. Note:all wiring related to the screen,may only be serviced by a manufacturer approved trained electrical technician.Tampering with electrical wiring may void warranty and release Panoview of liability.

Resumo do conteúdo contido na página número 8

NO.7 OPERA OPERATING INSTR TING INSTRUCTION: UCTION: Plug in power supply. For Switch control: Plug in Switch into switch jack. Press button to Up position, screen goes up. Press button to stop position, screen stops. Press button to down position, screen goes down. For IR Remote: Direct the handset to IR window on screen housing. Press the Up/Stop/Down button on the hand set, screen goes Up/Stop/Down accordingly.

Resumo do conteúdo contido na página número 9

N0.8 For 12V trigger: Input 12V trigger signal, screen goes down. Stop this signal, screen goes up. Electric lock: Press the Up & Down buttons on the IR handset together, then all Up & Down buttons on the switch and IR handset will be locked. To be unlocked press Stop button on the IR handset again or unplug the power supply and plug in again. Keeping the screen rolled in its protective case when not in use. Always examine both front and back of surface before re-rolling into

Resumo do conteúdo contido na página número 10