Manual do usuário Elite Screens CineTension 2

Resumo do conteúdo contido na página número 1

Tab-tensioned Electric Motorized Projection Screen
CineTension 2 Series


User’s Guide

























1
Rev.102111-AS
www.elitescreens.com info@elitescreens.com

Resumo do conteúdo contido na página número 2

Important Safety & Warning Precautions Make sure to read this user’s guide and follow the procedure below. • Please retain this user’s guide for future reference. • To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the manufacturer. • Handle the unit carefully during transportation to avoid any damages. • To ensure safe and reliable operation, direct connection to a properly grounded power source is advised. • The power outlet supplyi

Resumo do conteúdo contido na página número 3

Installation Warning Due to various installation environments, the instructions provided in this user’s guide are for reference only. Please consult a professional installation company for further installation and safety advice. The installer must insure that proper mounting hardware is used to provide adequate strength suitable for the installation. Elite Screens is not liable for any faulty installations. For limit adjustment instructions, please contact our Technical Support Departmen

Resumo do conteúdo contido na página número 4

Accessories for CineTension 2 Series Please make sure all accessories listed below are included before proceeding. A. B. C. D. IR Remote RF Remote 3 Way Wall Switch IR Eye Receiver Red+ Green- E. F. G. 12V Trigger AAA Batteries

Resumo do conteúdo contido na página número 5

Control System for CineTension 2 Series 1. 5-12V Trigger: The built-in 5-12V trigger input 3-prong power cable allows your screen to synchronize its drop & rise with the projector’s power cycle. The screen deploys when the projector powers up and will retract when the projector powers down. The 5-12 volt adaptor connects to your projector’s trigger output via a separate cable that may or may not be provided by the manufacturer of the projector. RJ-45 input for 5-

Resumo do conteúdo contido na página número 6

Hardware Parts List for CineTension 2 Series Please make sure all items listed below are included before proceeding with the installation. A B C D 120” & above x 3 brackets Hardware Parts List QTY A. Screw & Dry Wall Anchor 2EA. B. Bolt 2 C. Masonry Screw & Anchor 2EA. D. Extruded Hanging Bracket 2 or 3 Installation Instructions Please consult a professional installer. Elite Screens is not liable for any faulty insta

Resumo do conteúdo contido na página número 7

3. Mark the installation location to drill your hole. Insert the proper screw and secure the bolts to the bracket. Top hole for ceiling installation Back hole for wall installation 4. Example of the CineTension 2 installed to a wall, ceiling and enclosed. Flush mount Flush mount Enclosed to wall to ceiling installation *Allow 2” of spacing between the front and back of the screen casing. Adjusting the Tension String This adju

Resumo do conteúdo contido na página número 8

Troubleshooting & FAQ’S For additional information, please contact Elite Screens at techsupport@elitescreens.com 1. If your screen does not move, please check the power supply. The screen will understandably not move without power. 2. Make sure the power cord is firmly plugged to the power outlet. 3. Make sure that all cable connections are secure. 4. If the screen works well with the line switch but not with the remote control, please make sure the remote controls have fres

Resumo do conteúdo contido na página número 9

CineTension 2 Dimension Table *Measurement dimensions are intended as a reference only and subject to change without notice. Note: Data Error may be ±1" 9 Rev.102111-AS www.elitescreens.com info@elitescreens.com

Resumo do conteúdo contido na página número 10

Warranty Policy • Two (2) Year parts and labor warranty from defects in workmanship from purchase date as follows (except for refurbished units as specified below). • Three (3) Year parts and labor warranty from defects in workmanship for GEMR (Government, Educational, Military, & Religious) purchases of new product only. • Refurbished Units carry a 90-DAY parts and labor warranty. • Each party will be responsible for one way shipping during the warranty period. • A RMA (Return Merc

Resumo do conteúdo contido na página número 11

Contact Information US & Canada Tech Support & Warranty Claim Please contact us at service@elitescreens.com or call +1 877-511-1211 #3 or fax +1-562-926-8433 Europe Tech Support & Warranty Claim Please contact us at service@elitescreens.eu or call +49-(0) 40-30392958 Asia Tech Support & Warranty Claim Please contact us at service@elitescreens.com.cn or call +86-(0) 755-8461-7989 Taiwan Tech Support & Warranty Claim Please contact us at service@elitescreens.com.tw or call +866+2+8990