Resumo do conteúdo contido na página número 1
®
SD5BC Series Color
or SD5AM Series
Monochrome
Spectra II™
Dome Systems
Operation and
Programming Manual
C2419M-A (5/00)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
Resumo do conteúdo contido na página número 2
CONTENTS Section Page IMPORTANT SAFEGUARDS AND WARNINGS................................................................3 OPERATION ......................................................................................................................4 POWER-UP DISPLAY ...............................................................................................4 HOW TO OPERATE YOUR SPECTRA II LOWLIGHT COLOR OR MONOCHROME DOME ......................................................................
Resumo do conteúdo contido na página número 3
IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not be installed where exposed to rain and moisture. 3. Only use replacement parts recommended by Pelco. 4. After replace
Resumo do conteúdo contido na página número 4
OPERATION POWER-UP DISPLAY When the Spectra II™ dome is powered up, the selected protocol, revision number, and other information is displayed on the monitor. For example, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power- PELCO SPECT II 4.0 up mode. (Refer to the Power-Up Mode in the CONFIGURE DONE Programming section). Protocol C The information remains on the monitor until the dome is moved
Resumo do conteúdo contido na página número 5
OPERATING NOTES PAN AND TILT FUNCTIONS Controller Type Pan Tilt Fixed speed Speed determined by controller Speed determined by controller Variable speed 0.1 to 80° per second, depending on joystick position 0.1 to 40° per second, depending on joystick position Turbo Mode 150° per second 200° per second Preset Mode 250° per second Does not affect the tilt speed If the proportional pan mode is enabled (refer to Proportional Pan in the Programming section), the pan and tilt speeds will depend on th
Resumo do conteúdo contido na página número 6
PATTERNS The Spectra II dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half NOTE: The Spectra II patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt LowLight Color camera or lens command. Presets, flip, and turbo are not allowed in a pattern. Zone scan can be cannot do electronic zoom enabled while running a pattern. in a pattern. Optical zoom will operate in a pattern. Refer to the documentation for your control system to progra
Resumo do conteúdo contido na página número 7
AUXILIARY OUTPUTS An AUX 1 command from the controller will activate the relay in the dome and operate the device that is connected to the relay. The relay will remain latched until a clear command is issued. An AUX 2 command from the controller will place a ground at the output of AUX 2 to oper- ate the device that is connected to it. The output will remain latched until a clear command is issued. The output relay can also be programmed so that it is activated when any alarm input is activated.
Resumo do conteúdo contido na página número 8
PROGRAMMING Programming Guide - Spectra II LowLight Color Spectra II Monochrome Gain/AGC Menu 1. Access main menu (preset 95). 2. Make main menu selections. Joystick: Move up or down to position cursor or to toggle between selections. AGC mode Auto Iris Open: Enter Gain 0 Camera Menu Iris Close: Cancel Exit Backlight comp Off Zoom limit x- - Reset camera Auto-Iris Menu Exit Auto-iris mode Auto Auto-iris level 110 Line Sync Menu Auto-iris peak 16 Sharpness Menu Exit
Resumo do conteúdo contido na página número 9
ACCESSING MAIN MENU (PRESET 95) You can call up the main menu on your monitor by programming (setting or creating) preset NOTE: For American 95 (28 if in 32-preset mode). Dynamics controllers with only 32 presets, set switch Programming preset 95 for Pelco’s controllers varies according to the type of controller you SW1-7 on the dome drive in are using. Instructions for programming preset 95 are given below for various Pelco the ON position. When controllers. SW1-7 is ON, preset CM6700 99 become
Resumo do conteúdo contido na página número 10
ALARMS The Spectra II dome has seven alarm inputs, which can be designated as either high or low priority. The high priority setting is significant when more than one alarm is activated. If priority in alarms is not required, leave all alarms in the low setting. Refer to the Alarm Priority section. If presets 1-7 are not used for alarms, they can be used as regular presets. However, if they are being used for alarms, they should not be used for anything else. Also refer to the Alarm Dwell, Alarm
Resumo do conteúdo contido na página número 11
NOTE: The Spectra II 6. Position the cursor (>) beside the number of the alarm input for which you want to set the pattern. LowLight Color camera 7. Press the Iris Open button. The cursor moves to the right, beside the words Full Pat, cannot do electronic zoom Half Pat 1, Half Pat 2, or No Pattern. in a pattern. Optical zoom 8. Move the joystick up or down to toggle between the choices. will operate in a pattern. 9. SELECT - Press the Iris Open button on your keyboard to select your choice. CANC
Resumo do conteúdo contido na página número 12
AUTO FLIP Main Menu Other Menu Auto flip On Proportional pan On Limit stops On Park time minutes 0 Scan speed deg/s 25 Pattern length 6 min EXIT Exit There are two auto flip modes: On - Auto flip mode is enabled. Off - Auto flip mode is disabled. To change the auto flip mode: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Other. 3. Press the Iris Open button to enter the Other menu. 4. Positio
Resumo do conteúdo contido na página número 13
AUTO IRIS Main Menu Camera Menu Auto-Iris Menu Backlight comp Off Zoom limit x- - Auto-iris mode Auto Reset camera Auto-iris level 110 Auto-iris peak 16 Exit EXIT Exit The following are the settings for auto iris: Mode Level Peak To change the settings for auto iris: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Camera. 3. Press the Iris Open button to enter the
Resumo do conteúdo contido na página número 14
AUX MODE Main Menu Aux Menu Aux 1 mode Normal Aux 2 mode Normal Exit EXIT There are three settings for AUX mode: Normal - Controller operated. Latching - Pressing the AUX key turns on the AUX and the next press of the AUX key turns it off. Alarm - Any alarm input activates the AUX. Refer to your controller manual for operating instructions. To change the AUX mode: 1. Program preset 95 (28). The main menu appears. 2. Position the
Resumo do conteúdo contido na página número 15
GAIN/AGC Main Menu Camera Menu Gain/AGC Menu Backlight comp Off Zoom limit x- - Reset camera AGC mode Auto Gain 0 Exit EXIT Exit Gain - The amount of amplification the camera places on its video information in order to obtain a full 1-volt peak-to-peak video signal out. AGC - Automatic Gain Control. AGC MODE There are two AGC settings : Auto Mode - Automatically adjusts the gain. Off Mode - In the of
Resumo do conteúdo contido na página número 16
LIMIT STOPS Main Menu Other Menu Auto flip On Proportional pan On Limit stops On Park time minutes 0 Scan speed deg/s 25 Pattern length 6 min EXIT Exit There are two types of limit stops: Manual limit stops - A manual (joystick) pan operation stops when a limit stop is reached. Scan limit stops - The dome reverses direction during random, frame, or auto scanning when a limit stop is reached. Limit stops are controlled by software
Resumo do conteúdo contido na página número 17
LINE SYNCHRONIZATION Main Menu Line Sync Menu Line sync On Line sync phase 0 Exit EXIT If cameras are out of phase with each other, they may produce what appears to be vertical roll when switching between cameras. There are two settings for line synchronization: On - Adjust the synchronization of the power line voltage so that it is in phase with other cameras. Off - The dome synchronizes to an internal clock. To change the line
Resumo do conteúdo contido na página número 18
LOWLIGHT LIMIT (Color Camera Only) Main Menu Camera Menu Next Menu Backlight comp Off LowLight limit 2 Zoom limit x- - Shutter speed Auto Reset camera Auto focus mode Auto NOTE: LOWLIGHT does not mean NO LIGHT. Some Prev (back to prev. menu) type of illumination is EXIT Exit Exit required (street light, IR light, etc.) This setting determines the maximum length of time th
Resumo do conteúdo contido na página número 19
PATTERN LENGTH Main Menu Other Menu Auto flip On Proportional pan On Limit stops On Park time minutes 0 Scan speed deg/s 25 Pattern length 6 min EXIT Exit The Spectra II dome can do the following: One full pattern - 1.5, 3, or 6 minutes long. or Two half patterns - .75, 1.5, or 3 minutes long. This pattern can consist of any standard pan and tilt or lens command. Presets, flip, and turbo are not allowed in a pattern. Zone scan ca
Resumo do conteúdo contido na página número 20
3. Press the Iris Open button to enter the Power Up Mode menu. 4. Press the Iris Open button to move the cursor to the right. 5. Move the joystick up or down to cycle through the selections. Stop on the item you want to select. 6. SELECT - Press the Iris Open button on your keyboard to select your choice. CANCEL - Press the Iris Close button if you do not want to change the setting. PROPORTIONAL PAN Main Menu Other Menu Auto flip On Proportional pan On Limit stops
