Resumo do conteúdo contido na página número 1
®
SB19/SB1900 Series
Discreet Surveillance Enclosures
Installation/Operation Manual
C467M-D (5/95)
Pelco • 3500 W. Pontiac Way, Clovis, CA 93612-5699 • USA • www.pelco.com
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS Section Page 1.0 WARNINGS ........................................................................................................................................1 2.0 SCOPE ...............................................................................................................................................2 3.0 DESCRIPTION ...................................................................................................................................2 4.0 INSTALLATI
Resumo do conteúdo contido na página número 3
INSTALLATION AND OPERATION MANUAL CAUTION DISCREET SURVEILLANCE ENCLOSURES: This device is designed to operate at 24VAC power. MODEL SB19/SB1900 SERIES MODEL SB19-1/SB1901 SERIES Input voltage must not exceed 28 volts or drop be- MODEL DD1900 SERIES low 22 volts or else damage to the motors will occur. Should you need assistance with this or any Pelco product, please call 1-800-298-9100 or 1-559- 292-1981. 1.0 WARNINGS Prior to installation and use of this product, the following 3. Only use rep
Resumo do conteúdo contido na página número 4
2.0 SCOPE NOTE: The following are the cable require- The information contained within this manual covers ments. A relay box (RB24) is available to the SB19/SB1900 Series of Discreet Surveillance En- extend the operating distance. Consult the closures. factory for details. 3.0 DESCRIPTION Non-PP Models The SB19 is a low profile, hemisphere, discreet sur- veillance dome for CCD type cameras designed for ease 12 Conductors 13 Conductors* of installation, relocation, and servicing in hard ceiling
Resumo do conteúdo contido na página número 5
Figure 1. SB1900 Series Wiring Diagram Pelco Manual C467M-D (5/95) 3
Resumo do conteúdo contido na página número 6
4.3 MOUNTING INSTRUCTIONS 2. Remove the factory assembled 12.5" round face- plate from the back box by disengaging the ser- Determine the type of mounting desired. The enclo- rated studs. sure can be mounted in a hard ceiling, completely re- place a standard 2' x 2' suspended ceiling tile using the 3. Remove the factory assembled 14.5" square mount- APSB19 optional faceplate, or be inserted through a ing plate by removing the four (4) 1/4-20 bolts. cut-out in a standard 2' x 2' suspended ceilin
Resumo do conteúdo contido na página número 7
7. Slide the back box through the ceiling tile and mounting plate and replace the four (4) 1/4-20 bolts NOTE: For PC1804B and PC900U cameras, and tighten to secure the back box to the mounting remove the mounting bracket with the two 1/4- plate. 20 holes in it from the camera’s power supply, align the camera power supply so that the two 8. Check the alignment of the back box to the ceiling (2) threaded holes in the power supply align tile by attaching the 12.5" round faceplate trim to over two
Resumo do conteúdo contido na página número 8
13. Attach the dome to the pan/tilt by aligning the two 15. Attach the faceplate trim to the back box by align- ball studs protruding through the flange of the dome ing the two serrated studs with two of the holes in with the two holes in the dome attachment brack- the edges of the back box and engaging the studs. ets and engaging the studs. 16. Operate the pan/tilt to verify that there are no ob- 14. Attach the safety chain on the side of the back box structions or dragging cables within the ba
Resumo do conteúdo contido na página número 9
4.3.1.2 Suspended Ceiling Tile template. Also, the lens must not project higher than Replacement Mounting the long end of the template. To mount the enclosure into a suspended ceiling grid NOTE: If the camera and lens do not fit within where the tile is replaced, perform the following steps. the boundaries of the template, they will not fit inside the dome and need to be replaced with 1. Determine the location for mounting the enclosure smaller units. and remove the appropriate ceiling tile. 8.
Resumo do conteúdo contido na página número 10
12. Attach the safety chain on the side of the back box 6. Attach the lens and camera head to the tilt table to the short 4-40 threaded screw in the 12.5" round (hardware not supplied), if not factory pre-assembled, faceplate trim with the provided hardware. using the camera/lens position template supplied as a guide (see Figure 3). Locate the lens and cam- 13. Attach the faceplate trim to the back box by align- era so that when the notched area in the template ing the two serrated studs with tw
Resumo do conteúdo contido na página número 11
12. Attach the faceplate trim to the back box by align- 2. Pan to the desired left position, remove the drive ing the two serrated studs with two of the holes in unit from the back box and adjust the pan limit the edges of the back box and engaging the studs. stop until the actuator clicks, and lock into posi- tion. Replace the drive unit. 13. Operate the pan/tilt to verify that there are no ob- structions or dragging cables within the back box 3. Pan to the right and left to verify the exact po
Resumo do conteúdo contido na página número 12
5.0 CARE AND MAINTENANCE If dust or other debris accumulates on the inside of the lower dome, remove with clean air pressure only. Com- Regularly scheduled maintenance will prolong the op- pressed air cans are available from commercial photo- erational life and appearance of the equipment. graphic equipment and supply dealers. IMPORTANT: The lower dome of the en- Clean the outer surface of the dome and the inner sur- closure is an optical surface. When cleaning the face of the viewing window w
Resumo do conteúdo contido na página número 13
6.0 EXPLODED ASSEMBLY DIAGRAM Refer to Figure 7 for an exploded assembly diagram of the SB19 enclosure. PP ONLY * NON SL ONLY ** EXPASB1900 EXPASB1900PP Figure 7. SB19 Exploded Assembly Diagram Pelco Manual C467M-D (5/95) 11
Resumo do conteúdo contido na página número 14
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST Item Qty Description Pelco Part Number 1 1 UL, Pad, camera, black .062" thick EH200010004 2 1 PCB assembly, pan/tilt PCB3000100ASSY 3 1 Bushing, 3/8" tilt shaft PT180010001 4 1 Shaft, tilt table PT18004002COMP 5 1 Sprocket .25" bore with pin and SS PT18004003COMP 6 2 Ball stud receiver PT180410001 7 Not used 8 1 Tilt Chain assembly PT18041006ASSY 9 1 Pan Chain assembly PT18041007ASSY 10 1 Tilt shaft, motor side PT18041011WA 11 1 Frame body, weld assemb
Resumo do conteúdo contido na página número 15
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST (continued) Item Qty Description Pelco Part Number 48 Not used 49 Not used 50 Not used 51 1 Slip ring, 24 circuit for presets 250010000 52 Not used 53 Not used 54 Not used 55 1 Bracket, tilt pot PT18044012COMP 56 1 Bracket, LPP lens connector PT18044013COMP 57 1 Gear, 1.875 plastic PT250010002 58 2 Gear, 1.5 plastic PT250010006 59 2 Pot, precision 10K POTP010.0K 60 1 Gear, spindle feedback, non-SL PT25004114COMP 61 1 Pan feedback pot PT25004116COMP 62
Resumo do conteúdo contido na página número 16
8.0 MODELS SB1900-PP Same as the SB1900, except this package features the factory installed DD1900 Dome drive unit for SB1900. (UL) preset (PP) option. DD1900-PP Dome drive unit for SB1900-PP. SB1901-PP Same as SB1900-PP except supplied with clear viewing slot in the dome DD1900-SL Dome drive unit for SB1900-SL. for virtually zero light loss. (UL) SB1900SL-PP Same as the SB1900-SL with the DD1900SL-PP Dome drive unit for SB1900SL-PP. addition of the preset (PP) option. SB19 Drop ceiling discree
Resumo do conteúdo contido na página número 17
9.2 MODELS SB1900, SB1900-SL, IOP19B1C B/W NTSC 6X camera and lens pkg. SB1900-PP AND SB1900SL-PP with preset positioning. CM7500 Series Coaxitron Matrix Switcher/Control IOP19B1G B/W NTSC 10X camera/lens pkg. System rack mount card cage with CPU and power supply. Capable of IOP19C1B Color NTSC 6X camera and lens pkg. up to 64 inputs and up to 4 monitor outputs. (See C584 product specifi- IOP19C1C Color NTSC 6X camera and lens cation sheet for details). pkg. with preset positioning. CM8500 Seri
Resumo do conteúdo contido na página número 18
Pan Speed: 24°/sec ± 1° Lens Connector: Hirchmann 6100 type (mate supplied) for non-PP models Tilt: -90° movement from horizontal plane AMP CPC type (mate supplied) for PP models Tilt Speed: 12°/sec ± .5° Motors: Synchronous type, continuous duty, Maximum Load: 10 lbs (4.6 kg) instantaneous reversing Gearing: Chain drive Limit Switches: Pan 5 amp, 10 million cycle rating (ex- Bearings: ternal adjustment) on non-SL Pan Heavy duty ball bearing and Oilite Tilt 5 amp, 10 million cycle rating (factor
Resumo do conteúdo contido na página número 19
12.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved In order to expedite parts returned to the factory for repair or credit, please defective in material or workmanship for a period of one year after the date call the factory at (800) 289-9100 or (559) 292-1981 to obtain an of shipment. authorization number (CA number if returned for credit, and RA number Exceptions to this warranty are as noted below: if returned for repair)
Resumo do conteúdo contido na página número 20
Pelco 3500 Pelco Way • Clovis, CA 93612-5699 (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.) 18 Pelco Manual C467M-D (5/95)
