Resumo do conteúdo contido na página número 1
INST ALLA TION
TW3001AR
Active Receiver
Single Channel for UTP Transmission
C1666M-A (4/06)
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the po
Resumo do conteúdo contido na página número 4
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provi
Resumo do conteúdo contido na página número 5
Description The TW3001AR is a single-channel active receiver that can receive live video over unshielded twisted pair (UTP) cable. The adaptive technology in the TW3001AR automatically adjusts the low, medium and high frequency components of the video signal allowing for the best possible video transmission. The adaptive technology eliminates the need for manual adjustment by automatically adjusting to provide the most favorable video transmission depending on cable length needed. The unit
Resumo do conteúdo contido na página número 6
THISDEVICECOMPLIESWITHPART15OFTHEFCCRULES. OPERATIONISSUBJECTTOTHEFOLLOWINGTWOCONDITIONS: (1)THISDEVICEMAYNOTCAUSEHARMFULINTERFERENCE, AND(2)THISDEVICEMUSTACCEPTANYINTERFERENCERECEIVED, INCLUSINGINTERFERENCETHATMAYCAUSEUNDESIREDOPERATION. 1 23 45 PARTS OF THE RECEIVER MODEL SN FREQ W + - Figure 1. TW3001AR Parts Rubber Feet (4): For placing unit on a flat surface, such as a desk or shelf. Status LED: Lights red when there is no UTP video being received. Lights green when the
Resumo do conteúdo contido na página número 7
Installation Make sure all parts are present for the unit. 1 Universal power supply (Part #PS04-1502-0512G) 1 Wall clip 1 2-pin power connector 1 2-pin UTP connector MOUNTING The TW3001AR receiver is 3 rack units high and can be mounted into a fiber rack, onto a wall using a fiber wall mount kit or into the supplied wall clip. USING A RACK You can mount a TW3001AR into either an RK5000PS-3U (for power) or an RK5000-3U. For additional mounting information, refer to the RK5000PS-3U/RK5000-3U Fib
Resumo do conteúdo contido na página número 8
USING A WALL CLIP To attach the TW3001AR receiver to a wall using the supplied wall clip, refer to Figure 2 and do the following: 1. Attach the wall clip to a wall using two screws (not supplied). 2. Slide the receiver into the clip until the two holes on the bottom of the receiver align with the two holes on the lower flange of the clip. 3. Attach the receiver to the clip using the two Phillips pan head screws provided with the clip. UPPER FLANGE VERTICAL MOUNTING HOLE (2) HORIZONTAL TW300
Resumo do conteúdo contido na página número 9
SETTING THE DIP SWITCHES You can override the adaptive technology by manually adjusting switches 1 through 4 on the DIP Switch. The factory default switch positions are shown in Figure 3. Switches 1 through 4 are set to AUTO and Switch 5 is set to H MODE (high mode). Figure 3. Default Switch Positions If you want to transmit video over 4,000 feet (1,219 meters) of UTP cable, set switch 1 to 4K. Set switch 2 to 3K if you want a distance of 3,000 feet (914 meters), switch 3 to 2K if you want a
Resumo do conteúdo contido na página número 10
APPLICATIONS You can connect the TW3001AR active receiver to transmitters, such as the TW3001P passive trans- ceiver and the TW3001AT active transmitter, and to Pelco UTP cameras, such as the CC3710/CC3610 Series. Although you can connect these products using an unshielded twisted pair Cat3 and Cat5 cable, Cat5e and Cat6 are recommended for the best video performance. Always connect the UTP wires on the Cat cable from + to + and from - to -. For example, if you connect the blue wire to the +
Resumo do conteúdo contido na página número 11
® Figure 4 shows a TW3001AR connected to a UTP Camclosure . TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + - CAMCLOSURE UTP BLUE WIRE = MONITOR GRAY WIRE = Figure 4. TW3001AR Connected to a UTP Camclosure C1666M-A (4/06) 11
Resumo do conteúdo contido na página número 12
Figure 5 shows a TW3001AR connected to a UTP fixed camera. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + - FIXED CAMERA UTP PIN 5 + PIN 4 - MONITOR 10 PINS 8 PINS (4-/5+) (5-/6+) Figure 5. TW3001AR Connected to a UTP Fixed Camera 12 C1666M-A (4/06)
Resumo do conteúdo contido na página número 13
® Figure 6 shows a TW3001AR connected to a UTP Spectra Dome for Coaxitron PTZ control. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY SPECTRA + - VC-UTP BOARD COAXITRON UTP MONITOR VIDEO MATRIX Figure 6. TW3001AR Connected to a Spectra Dome C1666M-A (4/06) 13
Resumo do conteúdo contido na página número 14
Figure 7 shows a TW3001AR connected to a TW3001P passive transceiver. The TW3001P then connects to a non-UTP fixed camera. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + - UTP TW3001P DIRECT FIXED CONNECTION CAMERA MONITOR Figure 7. TW3001AR Connected to a Single Passive Transceiver 14 C1666M-A (4/06)
Resumo do conteúdo contido na página número 15
Figure 8 shows a TW3001AR connected to a TW3032P passive transceiver. TW3001AR POWER FROM RK5000PS-3U OR 12 VDC OR 24 VAC POWER SUPPLY + TW3032P - UTP MONITOR Figure 8. TW3001AR Connected to a 32-Channel Passive Transceiver C1666M-A (4/06) 15
Resumo do conteúdo contido na página número 16
Figure 9 shows a TW3001AR connected to a TW3004P passive transceiver. The TW3004P then connects to a non-UTP fixed camera. TW3001AR TW3004P 12 VDC OR 24 VAC POWER FROM RK5000PS-3U POWER SUPPLY OR + - 4 3 UTP 2 MONITOR FIXED CAMERA 1 Figure 9. TW3001AR Connected to a 4-Channel Passive Transceiver 16 C1666M-A (4/06)
Resumo do conteúdo contido na página número 17
Specifications ELECTRICAL Input Voltage 12 VDC or 24 VAC, 50-60Hz Power Consumption 2.5 W Wire Type Unshielded twisted pair (24 AWG maximum) Wire Category Cat3 or better DC Loop Resistance 52 ohms per 1,000 feet Differential Capacitance 19pF/ft max Transient Immunity 300 W peak pulse power (8/20 US) VIDEO CHARACTERISTICS Video Output 1, BNC Format NTSC, PAL, SECAM Frequency Response DC to MHz Common Mode/Differential Mode Rejection >70 dB MECHANICAL Connectors BNC Video output 4-Pin Connector R
Resumo do conteúdo contido na página número 18
18 C1666M-A (4/06)
Resumo do conteúdo contido na página número 19
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products. ® • Three years on Spectra IV products. ® • Three years on Genex Series products (multiplexers, server, and keyboard). ® • Th
Resumo do conteúdo contido na página número 20
Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.com ISO9001 Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore | | | | | | | | | South Africa Spain Sweden United Arab Emirates United Kingdom United States | | | | |
