Resumo do conteúdo contido na página número 1
45130
Wireless Alarm System
Garage Door
Sensor
User’s Manual
Choice
Choice
ALERT
ALERT™
™
Control all Sensors
& accessories from
one location
Resumo do conteúdo contido na página número 2
Table of Contents Important Safeguards 4 Introduction 5 Installation 6 Assigning a Sensor to a Zone 7-8 Erasing a Sensor from a Zone 8-9 Testing a Sensor or your system 9-10 Low battery indicator 10 Battery warnings 11 F.A.Q.'S 1 -1 FCC Warning 14
Resumo do conteúdo contido na página número 3
Before connecting or operating the Garage Door Sensor, please read these instructions carefully and save this manual for future reference. Congratulations ™ The GE Choice Alert Wireless Alarm System is one of the most affordable and expandable wireless alarm systems available. You’ll discover that the system offers many features typically found in custom installed Alarm systems. The Choice Alert system is reliable and easy-to- use. With Choice Alert you can select from a line of Sensor
Resumo do conteúdo contido na página número 4
Important safeguards PreCautions 1. Do not attempt to disassemble the Garage Door Sensor, unless described in the user’s manual. There are no user serviceable parts. . Handle with Care – Avoid striking or shaking. Improper use or storage could damage the Garage Door Sensor. Modifying or tampering the device or its internal components can cause a malfunction and void the Garage Door Sensor’s warranty. . If you feel the Garage Door Sensor or any part of the Choice Alert system is not op
Resumo do conteúdo contido na página número 5
Introduction The Garage Door Sensor is designed to be used specifically with vertical opening garage or shed doors. When mounted properly it monitors when the door is open or closed. If the door is opened, the Garage Door Sensor will transmit a signal to the Control Center. The settings on the Control Center determine if an alarm, alert or chime sounds. Parts Check List Identify all the parts before proceeding. Garage Door Sensor with mounting bracket 4 Screws Double sided tape Make sure
Resumo do conteúdo contido na página número 6
Preparing the Garage Door Sensor for Installation The Garage Door Sensor is a self-contained Sensor. Before installing open the battery door and, remove the yellow battery isolation tape from the Garage Door Sensor. This activates the Lithium battery inside the Garage Door Sensor. The approximate battery life is up to two years. When replacing the battery it is recommended to replace all Sensor batteries at the same time in order ensure proper operation of the entire system. Note: When
Resumo do conteúdo contido na página número 7
bottom edge of the Garage Door Sensor even with the door edge. In most applications you can use double sided tape (included). It is strongly suggested to mount Garage Door Sensor lightly to ensure operation. Once you are confident with the mounting position apply pressure to secure to surface. For a more secure installation you can use the included screws. with tape with screws Once the Garage Door Sensor is mounted, you’ll need to assign the Garage Door Sensor to a Zone on the Control
Resumo do conteúdo contido na página número 8
Follow these steps to assign a Sensor to a Zone. Step 1 – Press and hold the Learn button on the Control Center for three seconds. When the Control Center sounds a long beep, release the Learn button. Step 2 – Press the Zone button (1, 2, 3 or 4) for the Zone you want to assign to the Garage Door Sensor. The LED indicator for that Zone will begin to flash. Step 3 – Release the Zone button. Note: Zone 4 is for dedicated alerts only. Sensors in this Zone will not trigger an al
Resumo do conteúdo contido na página número 9
Learn button on the Control Center. The unit will beep once. Step 2 - While holding the Learn button, press and hold the Zone button to be erased. After five seconds the Control Center will sound two beeps and the Zone LED indicator will flash twice. Step 3 - Release all buttons. The Zone has been erased. Note: The Zone/Garage Door Sensor cannot be erased if: - The Zone has been triggered for an Alert or alarm. The Sensor/Zone must be reset. - There is loss of signal from
Resumo do conteúdo contido na página número 10
Note: The sensor has a LED that flashes to show when the sensor has triggered and transmitted to the main unit. Step 4 - When testing is complete, unplug the AC adapter, then plug the AC adapter back in and reinstall batteries. This returns the Control Center to standard operation mode. Note: The Control Center will automatically return to standard operation mode after 5 hours. Low Battery Indicator The Control Center continuously monitors all the Sensors. If the Control Center do
Resumo do conteúdo contido na página número 11
Note: The Sensor detection system is ‘range dependant’, which means Sensors located closer to the Control Center may seem to have batteries that last longer than those Sensors at a greater distance. The Lithium cell battery in the Garage Door Sensor can last up to two years. Model # Description Battery Type Battery Life* 45129 Control Center (4) “AAA” 24 months 45130 Garage Sensor (1) “2032” 24 months *maximum potential life based upon usage and location WARNING! Risk of personal i
Resumo do conteúdo contido na página número 12
Garage Door Sensor F.A.Q.’S Q. I bought a new Sensor and the Control Center will not recognize it. Why? A. First, make sure that the yellow battery isolation tape has been removed and that the battery is new. Second, ensure the battery is inserted into the Sensor according to polarity(+/-) markings. Third, confirm that the Sensor has been correctly assigned to a Zone. Q. I put the Sensor on Zone 4 and it will not set off the alarm. Why? A. Zone 4 is a Dedicated Alert Zone and is desig
Resumo do conteúdo contido na página número 13
Q. Why does one of my Zones continually flash? A. This can be caused by 1 of 2 conditions. First condition, if it is a rapid flash it means a Sensor in the Zone has a low battery. If more than one Sensor is in a Zone, you will need to test each Sensor by putting the unit into test mode (see pg. 9 of this manual). It may also be that a Sensor is out of range and cannot make contact with the Control Center. If this is the case, you may need to move the Control Center closer or use a Si
Resumo do conteúdo contido na página número 14
FCC Warning Any unauthorized changes or modifications to the equipment would void the user’s warranty and may conflict with both state and federal laws. The Choice Alert system complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1) The Choice Alert system may not cause harmful interference. ) The Choice Alert system may accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested
Resumo do conteúdo contido na página número 15
WARNING Limitations of Alarm Products This product should be tested periodically to make sure it is working properly. The product, if used properly, may reduce the risk of burglary, robbery, or other adverse events. However, JASCO is not an insurer, this product is neither insurance nor a guarantee that such an event will be prevented, and users should protect themselves with proper insurance. JASCO makes no representation that this product cannot be compromised or circumvented, that it w
Resumo do conteúdo contido na página número 16
is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. This Jasco product comes with a 1 year limited warranty. Visit 45130-1 www.jascoproducts.com for details. 01/09/08
