Resumo do conteúdo contido na página número 1
45132
Wireless Alarm System
Motion
Sensor
User’s Manual
Choice
Choice
ALERT
ALERT™
™
Control all Sensors
& accessories from
one location
Resumo do conteúdo contido na página número 2
Table of Contents Important Safeguards 4 Introduction 5 Assigning a Sensor to a Zone 6-7 Testing a Sensor or your system 7-8 Installation 8 Erasing a Sensor from a Zone 8-9 Low battery indicator 10 Battery warnings 11 F.A.Q.'S 1 -1 FCC Warning 14
Resumo do conteúdo contido na página número 3
Before connecting or operating the Motion Sensor, please read these instructions carefully and save this manual for future reference. Congratulations ™ The GE Choice Alert Wireless Alarm System is one of the most affordable and expandable wireless alarm systems available. You’ll discover the system offers many features typically found in custom installed Alarm systems. The Choice Alert system is reliable and easy-to-use. With Choice Alert you can select from a line of Sensors and Acce
Resumo do conteúdo contido na página número 4
Important safeguards PreCautions 1. Do not attempt to disassemble the Motion Sensor, unless described in the user’s manual. There are no user serviceable parts. . Handle with Care – Avoid striking or shaking. Improper use or storage could damage the Motion Sensor. Modifying or tampering the device or its internal components can cause a malfunction and void the Motion Sensor’s warranty. . If you feel the Motion Sensor or any part of the Choice Alert system is not operating correctly or
Resumo do conteúdo contido na página número 5
Introduction The Motion Sensor is designed to be used indoors or out. When mounted properly it can monitor large or open areas such as entrances, living rooms, family rooms, driveways, backyards, walkways, workshops, etc. When the Sensor detects motion, it will transmit a signal to the Control Center. The Zone selection and settings on the Control Center determine if an alarm or an alert sounds. Parts Check List Identify all the parts before proceeding. Motion Sensor with mounting bracke
Resumo do conteúdo contido na página número 6
DETECTING AREA: (Unit = meter) 1.2M 14 55∞ 55∞ 1 1∞ 12 10 8 6 27∞ 22∞ 22∞ 4 2 M 12∞ Preparing the Motion Sensor for Installation The Motion Sensor consists of 2 parts – The Sensor (Transmitter) and the w SENSOR all mount. Before installing, remove the screw from the battery door on the back 0 1 2 3 4 5 6 7 8 9 10 11 12 13 of the Sensor. You’ll need to attach the battery leads to a “9V” battery (not included); Take care to note the polarity markings. Replace the battery cover and secure
Resumo do conteúdo contido na página número 7
- To activate the Motion Sensor, press the Learn button located inside the battery compartment, or if mounted wave your hand in front of the Sensor (the red LED indicator will flash inside lens area in front of the Motion Sensor). Testing a Sensor or your system Once all the Sensors have been assigned to Zones in the Control Center you can now test your system. Step 1 Press and hold theLearn button for three seconds Step 3 Release the Zone button Input DC 12V Step 2 - + S
Resumo do conteúdo contido na página número 8
Step - Set the Notification Mode to switch ‘Alert’ position and begin activating Sensors one at a time. Note: The sensor has a LED that flashes to show when the sensor has triggered and transmitted to the main unit. Step 4 - When testing is complete, unplug the AC adapter, then plug the AC adapter back in and reinstall batteries. This returns the Control Center to standard operation mode. Note: The Control Center will automatically return to standard operation mode after 5 ho
Resumo do conteúdo contido na página número 9
Erasing the Sensor from a Zone Note: If you need to remove the Sensor from a Zone, the system will erase the entire Zone, so any other Sensors will need to be put back into that particular Zone. Step 1 - To erase a Zone, press and hold the Learn button on the Control Center. The unit will beep once. Step - While holding the Learn button, press and hold the Zone button to be erased. After five seconds the Control Center will sound two beeps and the Zone LED indicator will fl
Resumo do conteúdo contido na página número 10
However, you can check the Motion Sensor status independently by placing the Control Center in Test mode (see Testing a Sensor on page 7) and trigger the Sensor separately. If mounted, wave hand in front of Sensor, or press activation button for two seconds inside battery compartment. If the Sensor does not trigger an alert then replace the battery with a new one. Note: The Sensor detection system is ‘range dependant’, which means Sensors located closer to the Control Center may seem t
Resumo do conteúdo contido na página número 11
Model # Description Battery Type Battery Life* 45129 Control Center (4) “AAA” 24 months 45132 MotionSensor (1) “9V” 9 months *maximum potential life based upon usage and location WARNING! Risk of personal injury - Prolonged exposure to alarm siren may cause permanent hearing loss Battery Warning! - Remove batteries before storing the Alarm or Sensor for extended periods - Batteries may leak harmful liquids or ignitable materials or explode causing injury and product damage -
Resumo do conteúdo contido na página número 12
Motion Sensor F.A.Q.’S Q. I bought a new Sensor and the Control Center will not recognize it. Why? A. First, make sure that the battery is new and has been correctly attached to the terminals. Confirm that the Sensor has been correctly assigned to a Zone. Q. I put the Sensor on Zone 4 and it will not set off the alarm. Why? A. Zone 4 is a Dedicated Alert Zone and is designed to monitor Sensors in this Zone. It will only issue an alert (LED will flash, continuous beeping will be heard)
Resumo do conteúdo contido na página número 13
Sensor.This will cause low battery indication on the Control Center (See pg 10). Q. Why does one of my Zones continually flash? A. This can be caused by 1 of 2 conditions. First condition, if it is a rapid flash it means a Sensor in the Zone has a low battery. If more than one Sensor is in a Zone, you will need to test each Sensor by putting the unit into test mode (see pg. 9 of this manual). It may also be that a Sensor is out of range and cannot make contact with the Control Center.
Resumo do conteúdo contido na página número 14
FCC Warning Any unauthorized changes or modifications to the equipment would void the user’s warranty and may conflict with both state and federal laws. The Choice Alert system complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1) The Choice Alert system may not cause harmful interference. ) The Choice Alert system may accept any interference received including interference that may cause undesired operation. NOTE: This equipment has been tested
Resumo do conteúdo contido na página número 15
WARNING Limitations of Alarm Products This product should be tested periodically to make sure it is working properly. The product, if used properly, may reduce the risk of burglary, robbery, or other adverse events. However, JASCO is not an insurer, this product is neither insurance nor a guarantee that such an event will be prevented, and users should protect themselves with proper insurance. JASCO makes no representation that this product cannot be compromised or circumvented, that it w
Resumo do conteúdo contido na página número 16
is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. This Jasco product comes with a 1 year limited warranty. Visit 45132-1 www.jascoproducts.com for details. 01/18/08
