Resumo do conteúdo contido na página número 1
THD SATELLITE COMPASS
SC-110
Resumo do conteúdo contido na página número 2
Your Local Agent/Dealer Your Local Agent/Dealer 9-52 Ashihara-cho, 9-52 Ashihara-cho, Nishinomi Nishinomiy ya, Ja a, Jap pan an Te Telle ep phone : hone : 0798-65-2111 0798-65-2111 fax fax 0798-65-4200 0798-65-4200 :: F FIRST EDITION : IRST EDITION : FEB FEB .. 2004 2004 Printed in Japan Printed in Japan A All r ll riig ghts reserved. hts reserved. A2 A2 :: JUN JUN .. 30, 2004 30, 2004 PUB.No. PUB.No. OME-72570 OME-72570 **00014854600 00014854600** **00014854600 00014854600** ( ( DAMI DAMI ) )
Resumo do conteúdo contido na página número 3
SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING WARNING ELECTRICAL SHOCK HAZARD Turn off the power at the switchboard Do not open the equipment. before beginning the installation. Only qualified personnel Fire or electrical shock can result if the should work inside the power is left on. equipment. Do not install the equipment where it Do not disassemble or modify the may get wet from rain or water splash. equipment. Water in the e
Resumo do conteúdo contido na página número 4
TABLE OF CONTENTS TABLE OF CONTENTS ..................................................................................................ii FOREWORD ..................................................................................................................iv SYSTEM CONFIGURATION ...........................................................................................v EQUIPMENT LIST....................................................................................................
Resumo do conteúdo contido na página número 5
2.9.4 Time format............................................................................................................ 2-15 2.9.5 Demonstration mode.............................................................................................. 2-16 2.10 WAAS/DGPS Setup........................................................................................................... 2-17 2.11 OTHERS Menu.............................................................................................
Resumo do conteúdo contido na página número 6
FOREWORD A Word to the Owner of the SC-110 FURUNO Electric Company thanks you for purchasing the FURUNO SC-110 THD Satellite Compass. (Hereafter, for sake of brevity, we refer to SC-110 as Satellite Compass.) We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by
Resumo do conteúdo contido na página número 7
SYSTEM CONFIGURATION The SC-110 consists of an antenna, a display unit and a processor unit. The tri-antenna system helps reduce the influence of ship's motion (rolling). Antenna Unit SC-1203F Display Unit SC-502 Analog pitch 6 ports for Heading or Navigation Data Processor Unit Analog roll (5 AD-10/IEC 61162 ports, 1 AD-10 port) SC-1101 Log/Heading alarm : Option (Contact) External heading data External DPGS Beacon Receiver Category of Units Processor Unit: Protected from weather 12-24 VDC D
Resumo do conteúdo contido na página número 8
EQUIPMENT LIST Standard supply Name Type Code No. Qty Remarks GPS Antenna SC-1203F 1 Radome type Display Unit SC-502 1 Processor Unit SC-1101 1 CP20-02230* 004-378-110 TPPX cable 1 CP20-02260* 004-379-660 TNC cable CP20-02241* 004-378-200 1 For antenna unit For processor unit: Installation CP20-02600 000-041-905 1 CP20-02601*, Materials MJ-A7SPF0006-100 For display unit: CP20-02203* 004-380-660 1 Tapping screw (5X20, 4 pcs.) Spare Parts SP20-01101* 004-379-720 1 For
Resumo do conteúdo contido na página número 9
SPECIFICATIONS OF THD SATELLITE COMPASS SC-110 1 GENERAL 1.1 Heading Accuracy ±0.6° (95%) 1.2 Heading Resolution 0.1° 1.3 Follow-up 45°/s rate-of-turn 1.4 Settling Time 4 minutes 1.5 Position Accuracy 10 m, or 5 m (DGPS), 95% of the time 1.6 Heading/Nav Data Output AD-10 format: 1 port (specialty port) AD-10 format 5 ports or IEC 61162 format 10 ports (selectable on menu) IEC 61162 format is RS-485 level Sentence: HDT, HDM, ROT, ATT, VDR, VTG, GGA, GNS GLL, V
Resumo do conteúdo contido na página número 10
4.3 Waterproofing Antenna Unit IPX6 Display Unit IPX5 Processor Unit IPX0 4.4 Vibration IEC 60945 5 COATING COLOR 5.1 Display/Processor Unit Panel: N3.0 Newtone No.5 (dark gray) Chassis: 2.5GY5/1.5 (light gray) 5.2 Antenna Unit N9.5 (white) SP - 2 E7257S01B
Resumo do conteúdo contido na página número 11
1 INSTALLATION 1.1 Mounting Considerations 1.1.1 Antenna unit General • Keep the length of the antenna cable in mind when selecting a mounting location. Installing the antenna above superstructures • The antenna must be mounted above all other structures on the vessel to obtain an unobstructed view of the satellites regardless of vessel heading. Failure to do so will cause shadows and multipath reflection problems. Mast SC-series Antenna Radar Antenna Bridge Example of antenna in
Resumo do conteúdo contido na página número 12
1. INSTALLATION • The horizontal separation between the antenna and masts must be as follows: Mast diameter Separation distance (minimum) 10 cm 1.5 m 30 cm 3 m -80 +80 SC-series Antenna Less than 10 Mast, etc. Separation degrees • Keep the length of antenna cable in mind when selecting a mounting location. The cable comes in lengths of 15 meters (standard supply), or 30 m or 50 m (optional lengths). • The field of view above the antenna should be as shown below, ±80° against
Resumo do conteúdo contido na página número 13
1. INSTALLATION Location influenced Radar Antenna by reflected wave. Reception blocked by mast. SC-series Antenna Bridge Example of antenna installed below superstructures 1.1.2 Display unit, processor unit • Choose a location where vibration and shock are minimal. • Install the units well away from locations subject to rain and water splash. • Locate the units away from air conditioner vents. • Keep the units out of direct sunlight because of heat that can build up inside their ca
Resumo do conteúdo contido na página número 14
1. INSTALLATION 1.2 Installing the Antenna Unit Note: “Bird-repellent fixtures” may be attached to each antenna element and the center cover to prevent birds from alighting on them. If it is more convenient to attach them before fixing the antenna unit to the mounting location, do step 7 before fixing the antenna unit. 1. Prepare a post for the antenna as shown in the illustration below. f 15 Recommended Flange Gasket (Option) (supplied in installation materials) Name: Flange Type: OP20
Resumo do conteúdo contido na página número 15
1. INSTALLATION 2. Fix the antenna unit to the post as shown below. 3 1 2 Fix the #1 and #2 antennas on Set the antenna the fore-and-aft line of the ship, unit to the flange. with the #2 antenna forward of the #1 antenna. Flat washer Spring washer Nut (Torque: 29.58 Nm) Fastening antenna unit to a post 1-5
Resumo do conteúdo contido na página número 16
1. INSTALLATION 3. Coat each nut, bolt and washer with silicone rubber for waterproofing. Coat bolt, nut and washer completely with silicone rubber. Coating bolt, nut and washer with silicone rubber 4. As shown below, make a loop in the antenna cable and fasten the antenna cable to the antenna post with two cable ties. Coat bolt threads with Three Bond. Fasten bolt with nuts and then coat nuts with Three Bond also. Coat with Three Bond 1211 (supplied). Fix antenna cable. 5. Coat bolt t
Resumo do conteúdo contido na página número 17
1. INSTALLATION 1.3 Installing the Processor Unit The processor unit should be mounted aligned with the ship’s fore-and-aft line. It can be mounted on the deck, bulkhead, or on the underside of a desk. Choose a mounting location which allows you to easily view the power lamp on the top of the unit and which is within ±2.5° of the ship’s fore-and-aft line. 1.3.1 Bulkhead mount The processor unit is shipped from the factory ready for bulkhead mounting. Orient the processor unit as shown
Resumo do conteúdo contido na página número 18
1. INSTALLATION 1.3.2 Deck mount Orient the processor unit as shown below and fix it to the mounting location with four tapping screws (M5x20). You will set the orientation later on the menu. Mount processor unit Reference Direction so reference direction is within – 2.5 of POWER switch fore-and-aft line. (power lamp) Name plate Connectors Processor Unit, top view Bow Bow Mounting Method: "Floor" Mounting Method: "Floor" (Deck) (D
Resumo do conteúdo contido na página número 19
1. INSTALLATION 1.3.3 Installation on the underside of a desk The processor unit may be mounted on the underside of a desk as shown in the figure below. Do not install it on the overhead. Desk Name Plate Installation of processor unit on the underside of a desk Reference Direction Mount processor unit so reference direction is within – 2.5° of fore-and-aft line. Name plate (other side) POWER switch Connectors (power lamp) Processor Unit, rear view Bow Bow Mounting Method: Invert Mounting
Resumo do conteúdo contido na página número 20
1. INSTALLATION 1.4 Installing the Display Unit 1.4.1 Desktop, overhead mounting 1. Fasten the hanger to the mounting location with four tapping screws (supplied). See the outline drawing for mounting dimensions. 2. Screw the knobs into the display unit. 3. Set display unit to the hanger and tighten the knobs. 4. Run the ground wire between the ground terminal on the display unit and the ship’s superstructure. Desktop Overhead Display unit mounting methods 1.4.2 Flush mount Two ty
