Resumo do conteúdo contido na página número 1
Models WH30TQG and WH30XLR User Guide
MODEL WH30 CONDENSER HEADSET MICROPHONE
MICROPHONE DE CASQUE
ÉLECTROSTATIQUE
SHURE MODÈLE
WH30
KONDENSATOR
KOPFMIKROFON-
MODELL SHURE WH30
MICROFONO DE
CONDENSADOR DE
CABEZA MODELO
WH30 SHURE
MICROFONO A
CONDENSATORE
CON SUPPORTO A
CUFFIA SHURE
WH30XLR
ONLY
MODELLO WH30
©2006, Shure Incorporated
Printed in U.S.A.
27G3121 (Rev. 9)
Resumo do conteúdo contido na página número 2
INTRODUCTION The Shure Model WH30 is a light yet rugged headset microphone. Designed for vocalists and instrument-playing vocalists, the WH30 utilizes a high quality electret-condenser car- tridge suitable for all applications where mobility, comfort, low microphone-visibility, and high sound quality are required. Because of its cardioid (unidirectional) pickup pattern, the WH30 provides isolation from extraneous sound sources and high gain-before-feedback. The wireframe and gooseneck adjust to
Resumo do conteúdo contido na página número 3
MICROPHONE PARTS The WH30 consists of the following parts (see Figure 1). WH30 HEADSET MICROPHONE PARTS FIGURE 1 COLLAPSIBLE MICROPHONE BOOM The WH30 headset features a collapsible boom for shipment and storage. Before wearing the headset, unfold the boom by rotating it away from the wireframe until it snaps into place. Refold for storage or transportation. 3
Resumo do conteúdo contido na página número 4
WEARING THE HEADSET Place the headset wireframe around your head so that the elastic headband band lay hor- izontally across the back of your head and the ends of the wireframe fit over your ears. You may position the elastic headband either above or below the wireframe for the great- est comfort and stability. The blue “SHURE” logo should face outward (see Figure 2). WEARING THE HEADSET POSITIONING THE MICROPHONE FIGURE 2 FIGURE 3 POSITIONING THE MICROPHONE For maximum gain-before-feedback, po
Resumo do conteúdo contido na página número 5
ADJUSTING THE HEADSET • If the headset feels loose or uncomfortable, carefully bend the sides of the wire- frame to make it tighter or looser (see Figure 4A). The angle of the wireframe ear- pieces may also need adjustment (see Figure 4B). ADJUSTING THE WIREFRAME FIGURE 4 • Adjust the tension of the elastic headband across the back of the head by sliding it up or down the ends of the wireframe (see Figure 5). ADJUSTING THE ELASTIC HEADBAND FIGURE 5 USING THE CABLE RETAINER AND CLOTHING CLIP Us
Resumo do conteúdo contido na página número 6
CONNECTING THE WH30 TO A SOUND SYSTEM Wireless Applications (WH30TQG) 1. Connect the mini TA4F connector from the WH30 to a wireless microphone trans- mitter such as the Shure T1 bodypack transmitter. 2. See the user guide for your wireless transmitter and receiver system for adjusting gain and other parameters. Wired Applications (WH30XLR) Connect the output of the RPM420 preamplifier to an input channel of a mixing or record- ing console. Most consoles will provide phantom power to the RMP420
Resumo do conteúdo contido na página número 7
4. Rinse the windscreen in clean water and dry it with a clean cloth or paper towel. Allow it to air-dry thoroughly. 5. When the windscreen is dry, slide it over the WH30 microphone until the retain- ing ring snaps into place. CERTIFICATION WH30XLR : Conforms to European EMC Directive 89/336/EEC, and is eligible to bear the CE marking. Meets applicable tests and performance criteria in European standard EN 55103 (1996) parts 1 and 2, for residential (E1) and light industrial (E2) environments. W
Resumo do conteúdo contido na página número 8
SPECIFICATIONS WH30TQG WH30XLR Type Condenser, electret bias Condenser, electret bias with integrated preamplifier Frequency Response 40 to 20,000 Hz (See Figure 6) Polar Pattern Unidirectional (cardioid) (see Figure 7) Output Impedance (at 1kHz) 2400 Ω Rated 150 Ω (actual) (Tolerates loads as low as 150 Ω with reduced clipping level) Output Level –55.5 dB (1.7 mV) –54.5 dB (1.9 mV) (at 1 kHz; 0 dB = 1 V/Pascal) Signal to noise ratio (ref. 63.0 dB at 94 dB SPL (IEC 651) A-weighted noise) Out
Resumo do conteúdo contido na página número 9
1 cm. (0.4 in.) 61 cm. (24 in.) Hz TYPICAL WH30 FREQUENCY RESPONSE FIGURE 6 TYPICAL WH30 POLAR PATTERNS FIGURE 7 9 dB
Resumo do conteúdo contido na página número 10
WIRING DIAGRAMS WH30 WIRING DIAGRAMS FIGURE 8 10
Resumo do conteúdo contido na página número 11
47
Resumo do conteúdo contido na página número 12
TRADE MARK NOTICES: The stylized Shure logo and the Word “Shure” are registered trademark of Shure Incorporated in the United States. “Teflon” is a registered trademark of E.I. duPont de Nemours and Company in the United States. SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone: 847-600-2000 U.S. Fax: 847-600-1212 Intl Fax: 847-600-6446 Europe, Middle East, Africa: Shure Europe GmbH, Phone: 49-713
