Resumo do conteúdo contido na página número 1
Quick start guide
TL7610/TL7611
DECT 6.0 cordless headset
Resumo do conteúdo contido na página número 2
Getting started Battery installation Install the battery as shown below. After installing the battery, you may be able to make and receive short calls. For optimal performance, charge the headset battery for at least six hours before use. When not in use, recharge the headset by returning it to the headset base. . Press on both sides of the battery compartment cover and lift the cover up and off. 2. Insert the battery into the battery compartment. 3. Push the battery plug into the c
Resumo do conteúdo contido na página número 3
Getting started Battery charging After installing the battery, charge the headset by placing it in the headset base as shown below. The headset ON/OFF light will be on when the headset is charging. Push ON/OFF light Insert . Insert the headset into the 2. Push the headset downward headset base. until the ON/OFF light on the headset turns on. IMPORTANT INFORMATION Use only the supplied rechargeable battery or replacement battery (model BT9 545). T o obtain a replacement battery, call
Resumo do conteúdo contido na página número 4
Getting started Installation preparation If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through your telephone lines, you must install a DSL filter between the telephone line cord and the telephone wall jack. The filter will prevent noise and caller ID problems caused by DSL interference. Please contact your DSL service provider for more information about DSL filters. For customer service or product information, visit our website at www.telephones.att.com
Resumo do conteúdo contido na página número 5
Getting started Headset base installation IMPORTANT: If you purchased model TL76 , see the TL7000 handset lifter manual for installation instructions. Optional accessories It is recommended that you install a handset lifter (model TL7000) and/or a dial pad (model TL760 ) with your headset. The following optional accessories are compatible with your headset and base: • The TL7000 is a handset lifter with ring detector. • The TL760 is a dial pad that allows you to dial numbers and place c
Resumo do conteúdo contido na página número 6
Getting started Headset base installation Installation options IMPORTANT: If you purchased model TL76, or if you purchased a model TL7000 handset lifter (purchased separately), follow the installation instructions in the TL7000 handset lifter manual and then proceed on page 0 of this quick start guide. If you purchased model TL760 (without handset lifter), you have three installation options: Option : Use the headset with a single standard telephone line with a corded or cordless tel
Resumo do conteúdo contido na página número 7
Getting started Headset base installation Before installing the headset base: Remove the rear bottom piece of the headset base by pushing it away from the base (as shown in Figure ). Figure Install the headset base as shown on the following pages. After completing installation option or 2: Slide the rear bottom piece towards the base until it clicks into place (as shown in Figure 2). Figure 2 6
Resumo do conteúdo contido na página número 8
Getting started Headset base installation Option 1: Headset base with c orded or cordless phone installation (TL7610) 2. Plug one end of the 1. Plug the small end of the headset telephone line cord into the TEL WALL JACK (red base power dot) at the back of the adapter into the headset base. POWER jack (green dot) at the back of the 3. Plug the other end of headset base. the telephone line cord connected into the line splitter. Telephone line cord 4. Plug the lin
Resumo do conteúdo contido na página número 9
Getting started Headset base installation Option 2: Headset base stand-alone installation (TL7610) In order to make calls, you will need a telephone plugged into the same telephone line or a dial pad (TL760 sold separately). 1. Plug the small end of 2. Plug one end of the the headset base power telephone line cord into adapter into the POWER the TEL WALL JACK (red jack (green dot) at the dot) at the back of the back of the headset base. headset base. Telephone line cord 3. Plug the ot
Resumo do conteúdo contido na página número 10
Getting started Headset base installation Option 3: Headset base with corded phone for mul tiple line system or digital business system installation (TL7610) With this installation, you can make and receive calls using the LIFTER MODE without a lifter. 1. Plug the small end of 3. Unplug the curly the headset base power handset cord from adapter into the POWER the telephone. Plug jack (green dot) at the the end of the curly back of the headset handset cord into the ba
Resumo do conteúdo contido na página número 11
Getting started Quick reference guide - headset ON/OFF Press to make and/or answer a call, and end a call. The light is on when the headset is charging in the headset base. The light flashes slowly when you are on a call or flashes quickly when there is an incoming call. VOLUME Press the volume key on the side of the headset to adjust the listening volume when on a call. MUTE/FLASH Press to mute the microphone during a call. Press and hold to receive call waiting during a call. Pre
Resumo do conteúdo contido na página número 12
Getting started Quick reference guide - headset base Charging cradle Insert the headset here for charging. PAIR Press to register or de-register a headset. NO LIFTER MODE light On when NO LIFTER MODE is selected. Flashes while on a call or another telephone is in use on the same line. Flashes quickly when there is an incoming call. LIFTER MODE light On when the LIFTER MODE is selected. Flashes while on a call. Flashes quickly when there is an incoming call. MUTE light On when the call is m
Resumo do conteúdo contido na página número 13
Getting started Quick reference guide - headset base LIFTER AUDIO ADJUST Adjust the switch to choose the best headset audio quality when using a handset lifter. (See the handset lifter user's manual for more information. You may download the manual at www.telephones.att.com.) VOLUME Press the volume keys on the side of the headset base to adjust the speaking volume when on a call. MODE Press to choose between the NO LIFTER MODE or LIFTER MODE when the headset is not in use
Resumo do conteúdo contido na página número 14
www.telephones.att.com © 2008 Advanced American Telephones. All rights reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual Property II, L.P. d/b/a AT&T Intellectual Property licensed to Advanced American Telephones. Printed in China. Issue 1 AT&T 07/08.
