Manual do usuário Lowrance electronic s6500

Resumo do conteúdo contido na página número 1

Pub. 988-0151-361
Addendum I
LCX Sonar/GPS Series 25, 26,

110, 111 and GlobalMap GPS
Series 6500, 6600, 7500, 7600
This addendum addresses the manuals for the units listed above (part
988-0151-311 for the LCX sonar/GPS units and 988-0151-331 for the
GlobalMap GPS units). Since the manuals were written, some changes
have occurred to these units. These changes will affect the installation
and operation of your unit, and include:
Map Dataset Choice Menu (LCX-26, 111; GlobalMap 6600, 7600)
• The M

Resumo do conteúdo contido na página número 2

the MMC drawers or doors on the front of the unit. The other two choices, Lowrance MMC/SD and Navionics, require an MMC, SD or Navionics card. You must select the Lowrance MMC/SD set- ting to view information on a MMC or SD card, just as you must use the Navionics setting to view information on a Navionics card. Map Dataset Choice menu (left) for the LCX-26C HD and LCX-111C HD with the Lowrance MMC/SD option selected (right). Caution: Be sure and switch the Map Dataset Choice setting back to S

Resumo do conteúdo contido na página número 3

Hot Spots, Fishing Hot Spots Elite or Navionics chart, you must in- sert an MMC or SD card containing the mapping data into one of the MMC drawers or doors on the front of the unit. Choose the default Lowrance setting to view a MapCreate, FreedomMap, NauticPath, Fishing Hot Spots, MMC or SD card. Only when a Navionics card is loaded in the MMC drawer will you be able to select the desired Navionics chart from the Navionics Map Choice menu. The Navionics Options menu for the LCX-25C and LCX-110C

Resumo do conteúdo contido na página número 4

Here is the proper procedure for navigating a trail or route: 1. From the My Trails or Route Planning menu, press ↓ to the Saved Trails or Saved Routes list. To navigate a Trail: 2. Use ↑ ↓ to select a trail, then press ENT|→ ↓ to NAVIGATE|ENT. Press ↓ to NAVIGATE and press ENT. 3. Upon arrival at your destination, cancel navigation by pressing MENU|MENU|↓ to CANCEL NAVIGATION|ENT. To navigate a Route: 2. Use ↑ ↓ to select a route, then press ENT| ↓ to NAVIGATE|ENT. 3. Upon arrival at your desti

Resumo do conteúdo contido na página número 5

To add an MMC or SD Card 1. Open the card compartment door. 2. Grasp the bottom of the MMC and push the top of the card into the slot. Once the card is started, press down in the center of the card with the ball of your finger or thumb and push the card all the way to the left, until it is firmly seated in the slot. 3. Close the compartment door and fasten the thumb screw finger tight. Com Port Wiring The Com-2 communications port wiring diagram below was omitted from the LCX manual (page 33) an

Resumo do conteúdo contido na página número 6

Millimeter [Inch] Front view (left) and side view (right) showing dimensions of the LCX- 25 and LCX-26 mounted on gimbal brackets. Front view (left) and side view (right) showing dimensions of the LCX- 110 and LCX-111 mounted on gimbal brackets. 6

Resumo do conteúdo contido na página número 7

Sonar/GPS unit, rear view Sonar socket Power/Data socket Network socket LGC 2000 25' extension cable 60-ohm terminator NMEA 2000 Power Cable Power SP-BL optional Supply speed sensor Cable Transducer NMEA 0183 Data Cable GPS antenna module Cable connections, LCX-25 and LCX-26. 7

Resumo do conteúdo contido na página número 8

Sonar/GPS unit, rear view Sonar socket Power/Data Network socket socket LGC 2000 25' extension cable 60-ohm terminator NMEA 2000 Power Cable SP-BL optional Power speed sensor Supply Cable Transducer NMEA 0183 Data Cable GPS antenna module Cable connections, LCX-110 and LCX-111. Printed in USA 031705 8  Copyright 2005 LEI