Resumo do conteúdo contido na página número 1
GPS Receiver
GPS Receiver
531478-2_B
Resumo do conteúdo contido na página número 2
Thank You! Thank you for choosing Humminbird®, America's #1 name in Fishfinders. Humminbird® has built its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy - free of charge during the first year after purchase, and available at a reasonable r
Resumo do conteúdo contido na página número 3
WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE designed and intended as fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded from the WEEE Directive requirement. This symbol (WEEE wheelie bin) on product i
Resumo do conteúdo contido na página número 4
Table of Contents GPS Connection Kit 1 How GPS and Trackplotting Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Connecting a GPS Receiver to the Fishfinder . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GPS Receiver Installation 4 Stem Mount with 1” - 14 Thread. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Access Under Mounting Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 No Access Under M
Resumo do conteúdo contido na página número 5
Sonar X-Press™ Menu (Sonar Views only) 22 Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Cancel Navigation (only when navigating) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Navigation X-Press™ Menu (navigation views only) 24 Mark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Zoom . . . . . . . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 6
Setup Menu Tab 43 Units - Distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Units - Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Triplog Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Local Time Zone (Advanced) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Daylight Savin
Resumo do conteúdo contido na página número 7
GPS Connection Kit The Humminbird® GPS Connection Kit includes the following items: • GPS Antenna Receiver with 20' (6 m) cable • AS YC ("Y") cable for multiple accessory attachment • Hardware kit for stem or deck mounting • GPS Receiver Accessory Manual. NOTE: 10 foot extension cables are available as an optional purchase item. These can be used to extend the total Antenna Cable length up to 50 feet. How GPS and Trackplotting Work Your Humminbird® uses GPS and sonar to determine your position,
Resumo do conteúdo contido na página número 8
differences between each received signal, the GPS receiver determines its distance to each satellite. With distances known, the GPS receiver mathematically triangulates its own position. With once per second updates, the GPS receiver then calculates its velocity and bearing. The GPS Receiver allows you to combine easy-to-use trackplotting and navigation capabilities with advanced fishfinding. The following GPS functionality is currently supported by your Fishing System when it is connected to th
Resumo do conteúdo contido na página número 9
Fishing System AS-YC (“Y”) Cable Smartcast® WSL GPS Receiver WeatherSense® 5. The Fishfinder Control Head outputs NMEA signals through the "pigtail" cable attached to the end of the GPS receiver cable for connection to devices such as autopilots. Connect the NMEA Out (White Wire) of the cable to the NMEA In of the device you are connecting to your Fishfinder. The pinouts of this cable are as follows: • Red Wire, +12V (output voltage only) • Black Wire, Ground • White Wire, NMEA Out. CAUTION! Ple
Resumo do conteúdo contido na página número 10
GPS Receiver Installation To optimize performance of the GPS receiver, mount it in an area that has full exposure to the sky. The effective area of reception is 10° above the horizon. Different circumstances determine the mounting method appropriate for your GPS receiver. If you have… Then use... An antenna stem with standard 1" – 14 thread Stem Mount with 1" - 14 Thread Access under mounting location Access Under Mounting Location No access under mounting location No Access Under Mounting Locat
Resumo do conteúdo contido na página número 11
2. Screw on the receiver base to the stem first, making sure that the stem pipe does not protude from the receiver base. This adds protection to the cable NMEA when pulling it through the pipe stem. In addition to Pigtail Taped this, deburr the pipe edges to reduce cable abrasion. 3. Use electrical tape to secure the NMEA pigtail to NMEA Pigtail the cable as shown in the illustration. Cable Out NOTE: Leave the NMEA pigtail secured to the cable unless NMEA Pigtail needed in order to make it easie
Resumo do conteúdo contido na página número 12
2. Mark the mounting location and drill a 3/4” (19 mm) hole for the cable and cable connector. Secure the NMEA pigtail to the cable with electrical tape. Route the cable. 3. Cover the cable hole with the GPS receiver. Make sure the receiver is flush against the surface and mark the two mounting holes with a pencil or awl. 4. Move the receiver to the side and drill two pilot holes, using a 5/32” (4 mm) bit. NOTE: Apply marine-grade silicone caulk or sealant to both screw and drilled holes as need
Resumo do conteúdo contido na página número 13
2. Confirm that the cable length is adequate and route the cable from the receiver to the Fishfinder control head. If holes are required to route the cable, they must be 3/4” (19 mm) to allow for the cable connector. Secure the NMEA pigtail with electrical tape. 3. The GPS receiver has two wire routing notches. Use the cable notch closest to the intended cable route. 4. With the cable routed, position the GPS receiver in the planned mounting location and mark the mounting holes with a pencil or
Resumo do conteúdo contido na página número 14
Views Sonar Views The following views will be added to the View Rotation when a GPS receiver is connected to the Fishfinder Bird's Combo Fishing System: Eye View View Navigation views: Track View • Bird’s Eye View • Track View • Combo View. Bird’s Eye View Bird's Eye View - This view shows a 3-D, perspective view of the track from a point above and behind the boat (the eye point). As the boat turns, the eye point moves to follow the boat. When you press the 4-WAY Cursor key in the Bird’s Eye Vie
Resumo do conteúdo contido na página número 15
Track View Track View - This view shows the current track (also known as the position history or breadcrumb trail) showing where the boat has been, along with saved tracks, waypoints, and the current route (when navigating). Track View with Active Cursor Depth Track Scale Latitude and Active Cursor Longitude Position of Cursor Distance to Go To Cursor Bearing of Boat with Respect Bearing to North to Cursor Panning: Use the 4-WAY Cursor keys to move the grid around on the display in the direction
Resumo do conteúdo contido na página número 16
Combo View Combo View - This view is displayed as a split screen, with Track View on the left and Sonar View on the right side of the screen. The width of the sonar window can be changed. Combo View Depth Sonar Window Track Scale Water Bearing of Surface Boat with Temperature Respect to North Speed of Boat View Orientation Both Track and Combo views allow you to choose the orientation of the view. When North-Up orientation is selected, North is shown at the top of the display. In other words, ob
Resumo do conteúdo contido na página número 17
Introduction to Navigation Use your Fishfinder to establish waypoints at areas of interest and to navigate to those waypoints via a route (representing the shortest intended distance between waypoints). You can also view and save tracks, which represent the actual path of the boat. Waypoints, Routes and Tracks Waypoints are stored positions that allow you to mark areas of interest or navigation points. Your Fishing System can store up to 750 waypoints. Waypoints, Routes and Tracks Waypoint Depth
Resumo do conteúdo contido na página número 18
Save, Edit, or Delete a Waypoint Save your current position as a waypoint: On any view, press the MENU key to display the X-Press™ menu. Select Mark and press the RIGHT Cursor key to save the current position of the boat as a waypoint. Save the cursor position as a waypoint: On the Track or Combo view, use the Cursor key to designate the position you want to save as a waypoint. Then press the MENU key to display the X-Press™ menu. Select Mark and press the RIGHT Cursor key to save the current po
Resumo do conteúdo contido na página número 19
to represent the waypoint on the Combo and Track Views. You can exit these fields with the LEFT and RIGHT Cursor keys or by pressing the EXIT key. Select Save and press the RIGHT Cursor key to save your changes. To make it easier to select a waypoint, select Sort By and press the RIGHT or LEFT Cursor keys to select a sort order: • Name shows the waypoints alphabetically • Time shows the most recently-created waypoint first • Distance shows the closest waypoint first. Delete a waypoint: From the
Resumo do conteúdo contido na página número 20
Add a Waypoint Target or Trolling Grid Add or Remove a Waypoint Target: From the Waypoints submenu, select Target and press the Waypoint Target RIGHT Cursor key to display a list of waypoints. Select the waypoint you want to target. A target consisting of concentric circles centered on the selected waypoint will appear on all of the navigation views; the target shows various Track Scale distance ranges from the targeted waypoint. To remove the target, choose Remove Target from the Navigation X-P
