Resumo do conteúdo contido na página número 1
R
E
B
E
W
®
®
GENESIS SILVER–C
GENESIS SILVER–C
Gas Grill
Owners Guide
m DANGER
If you smell gas:
1. Shut off gas to the appliance.
Liquid Propane Gas
2. Extinguish any open flames.
3. Open lid
4. If odor continues, keep away from the
appliance and immediately call your gas
®®
supplier or your fire department.
Leaking gas may cause a fire or explosion
which can cause serious bodily injury or
death, or damage to property.
m WARNING
1. Do not store spare liquid propane
cylinder within 10 feet (3m)
Resumo do conteúdo contido na página número 2
m DANGER Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual may result in serious bodily injury or death, or in a fire or an explosion causing damage to property. m WARNINGS m Do not store a spare or disconnected liquid propane cylinder under or near this barbecue. m Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. m After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas le
Resumo do conteúdo contido na página número 3
Warranty Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Grill There are no other express warrants except as set forth that it will be free of defects in material and herein and any applicable implied warranties of workmanship from the date of purchase as follows: merchantability and fitness are limited in duration to the period of coverage of this express written Limited Aluminum Castings, lifetime, 1 year paint Warranty. Some regions do not allow
Resumo do conteúdo contido na página número 4
Contents Danger & Warnings ................................ A-2 Warranty ................................................. A-3 General Instructions ............................... A-5 Exploded View ........................................ A-6 Parts List ................................................ A-9 Assembly Instructions ............................ B-1 Installing Features .................................. C-1 Operating ............................................... D-1 Lighting.........
Resumo do conteúdo contido na página número 5
Storage General Instructions • The gas must be turned OFF at the LP cylinder Your Weber Gas Barbecue is a portable outdoor when the Weber Gas Barbecue is not in use. cooking appliance. With the Weber Gas Barbecue you • When the Weber Gas Barbecue is stored indoors, can grill, barbecue, roast and bake with results that are the gas supply must be disconnected and the LP difficult to duplicate with indoor kitchen appliances. The cylinder stored outdoors in a well-ventilated space. closed lid and Fl
Resumo do conteúdo contido na página número 6
Genesis Silver-C LP 1 2 27 3 28 4 29 5 30 6 31 32 7 33 8 34 9 35 36 10 37 11 38 12 13 39 40 41 14 42 43 44 15 45 46 16 47 17 33 18 48 17 49 19 50 20 21 51 22 52 23 53 24 54 55 25 26 56 57 A-6
Resumo do conteúdo contido na página número 7
1. Hinge Pin 27. Hair Pin Cotter 2. Left Endcap 28. Thermometer 3. Shroud 29. Right Endcap 4. Handle 30. Burner Control Knobs ™ 5. Warm-Up Basket 31. Control Panel 6. Warming Rack 32. Ignitor Button 7. Cooking Grates 33. Control Panel Hardware ® 8. Flavorizer Bars 34. Side Burner 9. Cooking Box 35. Crossover tube 10. 1/4-20 keps nut 36. Front and Back Burners 11. Slide Out Bottom Tray 37. Center Burner 12. Catch pan holder 38. Spider Stopper Guards 13. Catch pan 39. Manifold, Hose and regulator
Resumo do conteúdo contido na página número 8
© 1999 Weber-Stephen Products Co., Weber, the silhouette, and the kettle configuration are registered trademarks ® of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL, 60067-6266, U.S.A. This product is covered by one or more United States patents and patents in other nations globally. Printed in the U.S.A. A-8
Resumo do conteúdo contido na página número 9
® ® ® ® ® You will need: Left Frame - 1 Screwdriver Phillips screwdriver Right Frame - 1 Hammer Wheel Frame - 1 7/16 open-end or an adjustable wrench Pliers Caster Frame - 1 Block of wood Frame Connectors - 2 Lid - 1 Sideburner - 1 Work Surface - 1 Cooking Box - 1 Left Swing-Up Work Surface - 1 Right Swing-Up Work Surface Hinge Rod - 2 Cooking grates - 2 Left Trim Piece - 1 Control panel - 1 Right Trim Piece - 1 Wheel Axle - 1 A-9
Resumo do conteúdo contido na página número 10
Bottom Shelf - 1 Liquid Propane Cylinder - 1 Warming Rack - 1 Manifold Support Bracket - 1 Warm-Up Basket - 1 Burner Control Knobs - 3 Flavorizer Bars - 5 Hinge Pins (1/4 x 1 1/2 inch clevis pin) - 2 Cylinder Panel - 1 2 inch bolts (1/4 x 20 x 2 inch bolts) - 5 Front Panel - 1 1 3/4 inch bolts (1/4 x 20 x 1 3/4 inch bolts) - 2 Back Panel - 1 1/2 inch bolts (1/4 x 20 x 1/2 inch bolts) - 8 Bottom tray - 1 Keps Nut (1/4 x 20 Keps Nut) - 1 Catch Pan Holder - 1 Wing Nut (1/4 x 20 Wing Nut) - 2 Catch-
Resumo do conteúdo contido na página número 11
R E B E W Assembly Instructions Assemble wheel frame Assemble frame You will need: axle rod, two wheel hubcaps, two You will need: left frame, right frame, two 1/2 inch wheels, wheel frame, hammer and a block of wood. bolts, two nylon washers and a 7/16 inch or adjustable Place one end of the axle rod on the block of wood (or wrench. other protected surface). Tap one hubcap onto the end Note - Work on carpeted area (on grass or one of the of the axle rod. Slide one wheel onto the axle, WEBER box
Resumo do conteúdo contido na página número 12
Continue frame assembly Add back panel You will need: caster frame and wheel frame. You will need: frame assembly, back panel, two 1/2 Place the caster frame onto the tabs of the left frame, inch bolts, two nylon washers, and a 7/16 or adjustable so that the swing table locking bracket (1) is to the rear. wrench. Place the wheel frame onto the tabs of the right frame, Place the back panel against the inside frame assem- so that the swing table locking bracket is to the rear bly as shown in illus
Resumo do conteúdo contido na página número 13
Insert casters You will need: frame assembly and two casters. Slide the cooking box (assembly) to the left within the Push the casters firmly into the inserts in the ends of frame assembly. Add the nylon washer to the bolt. the caster frame. Insert the bolt through the frame and cooking box with the head of the bolt outside the box. Add the keps nut. Tighten by holding the bolt with pliers while you tighten the nut with a wrench. Add cooking box (assembly) You will need: frame assembly, cooking
Resumo do conteúdo contido na página número 14
Install cylinder panel Add fuel gauge You will need: Cylinder panel, two 1 3/4inch bolts, two You will need: fuel gauge, two wing nuts and two nylon nylon cylinder glides, two nylon washers a 7/16 inch or washers. adjustable wrench and pliers. 1) Slip the bolts on the back of the fuel gauge Insert the cylinder panel tabs(1) into the slots in the through the two small holes in the cylinder panel. frame brace(2). 2) Add washers to the bolts, then wing nuts, and (2) tighten with your fingers. (1) (
Resumo do conteúdo contido na página número 15
Install igniter Check that all burner valves are off Note - The igniter wires are already attached to the You will need: burner control knobs. Gas Catcher Ignition Chamber and the igniter. This Valves are shipped in the OFF position, but you should was done to factory test the ignition system. check to be sure that they are turned OFF. Put the The igniter lock nut is on the igniter. knob on each valve. Check by pushing down and 1) Loosen the igniter lock nut. turning clockwise. If they do not tu
Resumo do conteúdo contido na página número 16
Install manifold bracket You will need: manifold bracket. Slide the bottom tray onto the mounting rails under the Hook the bracket(2) onto the manifold at the center cooking box with finger grip toward you(1). burner valve. Place your hand underneath the bracket. WARNING: Do not line bottom tray with alumi- Lift the manifold, bracket and cooking box slightly, then num foil. It can cause grease fires by trapping the hook the tab of the bracket onto the frame brace(1). grease and not allowing gr
Resumo do conteúdo contido na página número 17
Install Lid Install control panel and burner control knobs You will need: lid, two hair pin cotters(1) and two hinge You will need: control panel, two Phillips screws/ pins(2). washers, a Phillips screwdriver, and burner control Place lid on top of the cooking box. Align the hinges at knobs. the rear of the barbecue. Insert hinge pins through the 1) Set the control panel in place over both frame hinges from the outside. Insert hair pin cotters into the braces. Hold the Crossover Ignition button
Resumo do conteúdo contido na página número 18
Installing Features Install the right end trim piece with tool holders 3.) Insert one end of the swing-up work surface rod and right swing-up work surface into the hole in the frame. You will need: Right trim piece with tool holders, right swing-up work surface, swing-up work surface rod, one 1/2 inch bolt, one nylon washer and a wrench 1.) Start the right end trim piece into the frame as shown, do not push the trim piece in all of the way and do not add bolt yet. (1) 2.) Slide the swing-up work
Resumo do conteúdo contido na página número 19
4.) While holding swing-up work surface in position, To raise swing-up work surface: Lift table all the way up insert the other end of the swing-up work surface and slide it to the left, then lower table until you feel it rod into the right end trim piece (1). Push the trim lock in the up position. piece into the frame as shown, making sure that the tab on the back underside piece of the trim To lower swing-up work surface: Lift table up until it piece is snapped into the slot in the rear frame
Resumo do conteúdo contido na página número 20
Install side burner Set the side burner in place in the frame. The side You will need: side burner, burner locking clip on the right should latch under the m WARNING: Make sure gas supply is off. right trim piece. Start the side burner hose into the opening between Route the hose between the cylinder panel and wheel the control panel and right trim piece. frame. Tilt the side burner slightly, toward the control panel. Latch the side burner locking clip on the left, under the control panel. Push
