Resumo do conteúdo contido na página número 1
Owner's Manual
E L I T E
®
Liquid Propane Gas Grill
Model141 16690
Natural Gas Grill
Model 14117690
WARNING: Note to Installer: Leave this Owner's Manual
with the consumer after delivery and/or installation.
Read this Owner's Manual carefully and be sure
your gas grill is properly assembled, installed and
Note to Consumer: Leave this Owner's Manual
maintained. Failure to follow these instructions
in a convenient place for future reference.
could result in serious bodily injuryand/or property
dam
Resumo do conteúdo contido na página número 2
/_kWARNING Warranty ..................................................... 2 Combustion byproducts produced when using Safety Instructions ..................................... 2 this product contain chemicals known to the State of California to cause cancer, birth Hardware ............................................................ 6 defects, or other reproductive harm. Parts Diagram and Lists ........................ 7 AX WARNING Assembly Instructions ............................... 10 Failure
Resumo do conteúdo contido na página número 3
18-1/2incheshigh is the maximum size LP gas • LP gas tanks must be stored outdoors in a tank to use. You must use an "OPD" gas tank well-ventilated area and out of the reach of which offers an Overfill Prevention Device. children. Disconnected LP gas tanks must not This safety feature prevents the t_nk from being be stored in a building, garage or any other overfilled which can cause malfunction of the LP enclosed area. gas tank, regulator and/or grill. • When your gas grill is not in use the ga
Resumo do conteúdo contido na página número 4
Figure 1 (Natural gas model only) IMPORTANT: your Kenmore Natural Gas Grill cannot GAS SUPPLY be converted to use LP Gas. Attempting to do so INSIDE is extremely hazardous and will also void the grill WALL warranty. OUTSIDE WALL Your natural gas grill is designed to operate on TO GRILL natural gas only, at a pressure of 7" water column (W.C.) (1/4 psi or 1.75 kpa), regulated at the SHUT OFF LOCKING residential meter. Check with your gas utility company for local gas pressure and with your local
Resumo do conteúdo contido na página número 5
CAUTION:Spidersandsmallinsects occa- To reduce the chance of "FLASHBACK" (see sionally spin webs or make nests in the grill CAUTION at right) clean the Burner Tubes and Burner Tubes during transit and warehousing. Burners before fully assembling your grill. These webs can lead to a gas flow obstruc- Remove the Cotter Pin from the rear underside tion which could result in a fire in and around of each Burner using a pair of long nose pliers. the Burner Tubes. This type of fire is known Carefully l
Resumo do conteúdo contido na página número 6
The following table illustrates a breakdown of the hardware pack. It highlights what components are used in the various stages of assembly, Ref. Component Qty. Purpose of Components H005 1/4"x1/2" Phillips Head Screw 16 Install Caster To Caster Seats of Bottom Shelf H030 1/4"x50mm Phillips Head Screw 8 Attaches Cart Side Panels To Bottom Shelf H005 1/4"xl/2" Phillips Head Screw 8 Attaches Rear Panel To Cart H005 1/4"x1/2" Phillips Head Screw 4 Attaches Tank Pull-out Tray Kit To Bottom Shelf (LPG
Resumo do conteúdo contido na página número 7
LPG= LiquidPropane Gas NG = Natural Gas l_ 24_ 39 19 28 -(LPG only) 4O 17o 32 33 38 !7b 59 (LPG only) (LPG 43 {LPG only)67o G only)67b 72(LPG only) 7_5(LPGonly) 53
Resumo do conteúdo contido na página número 8
REF# DESCRIPTION PART# QTY 1. Stainless Steel Lid P00117356A 1 2. Stainless Steel Lid Trim Plate POO11435EA 1 3. Lid Side Panel - Left PO0105347U 1 4. Lid Side Panel - Right PO0106347U 1 5. Temperature Gauge P00601171A 1 6. Lid Handle P00205033B 1 7. Name Plate P00410038C 1 8. S/S Secondary Cooking Rack P01518028B 1 P01606030B 9. S/S Stainless Steel Cooking Grid 3 10. SIS Stainless Steel Cooking Grid - 4" Size P01606031B 1 11. S/S Stainless Steel Flame Tamer P01708031B 3 12. S/S Stainless Steel
Resumo do conteúdo contido na página número 9
REF# DESCRIPTION PART# QTY 44b. Rear Panel (NG only) PO7702014E 1 45 Door Bracket P03301022J 1 46 Door Panel - Left P04302011A 1 47 Door Panel - Rigjht P04303011A 1 48 Door Trim Plate - Left P07506007D 1 49 Door Trim Plate - Right P07507007D 1 50 Door Axle Bracket - Left Top P03314018C 1 51 Door Axle Bracket - Left Bottom P0331401gc 1 52 Door Axle Bracket - Right Top P03314020C 1 53 Door Axle Bracket - Right Bottom P03314021C 1 54 S/S Door Handle POO205036B 2 55a Wire Basket P0520401OE 1 55b Div
Resumo do conteúdo contido na página número 10
Figure 1 CAUTION: While it is possible for one person to assemble this grill, obtain assistance from another personwhen handling some of the larger, heavier SEAT pieces, especially the grill head. BOTTOM 1. Open Lid of shipping carton and remove top sheet of J SHELF cardboard. Lay cardboard sheet on floor and use as a work surface to protect floor and grill parts from scratches. 2. Slice all carton corners with a sharp utility knife to lay open the carton panels. This will allow you to raise the
Resumo do conteúdo contido na página número 11
Figure 4 (LP gas model only) 5. Place the Tank Pull-out Tray Kit on the Bottom Shelf. Extend the Tank Tray outward from its Bracket so you can align the holes on the Bracket CART SIDE with the threaded holes on the top of Bottom Shelf. PANEL*LEFT REAR PANEL Tighten securely by using 4 of the 1/4"x1/2" Phillips TANK PULL-OUT Head Screws provided. See Fig. 4. Slide tray back TRAY KIT into Bracket. (LP gas model only) 6. Before installing the Door Bracket to the inside of front Cart Side Panels be
Resumo do conteúdo contido na página número 12
Installing The Cabinet Doors and Wire Basket Figure 8a 1, Remove the white protective film from the stain- less steel Door Panel and stainless steel Door Axle Bracket. PANEL-L CART SID_T _ 2. Install the Door Axle Bracket-left bottom to the Left Cart Side Panel, Align the threaded holes on the Door Axle Bracket-left bottom with the holes on the bottom of Left Cart Side Panel. Tighten securely by using 2 of the 3/!6"x9mm Phillips Head Screws provided. See Fig. 8a. 3. Place the axle on bottom of t
Resumo do conteúdo contido na página número 13
Installing The Grill Head Figure 9 1. Now that you've assembled the grill cart you can install the pre-assembled Grill Head. See GRILL HEAD CART SIDE Fig. 9. If you haven't already done so, open PANEL the Grill Lid and remove the packed BRACKET components. Lock the casters. Even with the BOWL SIDE components removed, the next step requires 2 PANEL people. 2. With an assistant, carefully lift and position the Grill Head onto the grill cart. Align the 6 holes of the Bowl Side Panel to the threaded
Resumo do conteúdo contido na página número 14
Installing Manual Lighting Stick Figure 11 1. Attach the Manual Lighting Stick to the Left Bowl Support Bracket as shown in Fig. 11. Align the hole at the end of Manual Lighting OUTSIDE BOWL Stick Wire with the threaded hole on the Left PANEL-LEFT Bowl Support Bracket. Tighten securely using the M4x8mm Phillips Head Screw. M4x8mm PHILLIPS HEAD SCREW I _ MANUAL LIGHTING STICK Installing Side Shelf and Cart Side Handle Figure 12 1. Remove the white protective film from the stainless steel Side She
Resumo do conteúdo contido na página número 15
Installing Cooking Components Electrode Check - Requires an Assistant Before placing the cooking components into your Important: Before cooking on your grill the first grill, ensure that the Spark Electrode Tip is properly time, wash the Cooking Grids and Cooking Rack positioned within each Gas Collector Box ( a with warm, soapy water. Rinse and dry thoroughly. 3-1/4" wide stainless mechanism found at the front Season with cooking oil regularly, After cooking is between each set of Burners.) The
Resumo do conteúdo contido na página número 16
Figure 16a Fuel Gauge Display Installation. IMPORTANT: Before installing batteries be sure the CART SIDE PANEL-RIGHT gas tank is not mounted inthe tank pull-out tray. _REAR PANEL 1, Open the frontDoorsof Cabinet. Pullout the LPG Tank Pull-out Tray. Connect the Wire Plug "A" from Fuel Gauge Displaywiththe Wire Plug "B" from rear of Tank Pull-outTray. Unscrew 1/4"x 1/2" Phillipshead Screw from Rear Panel and install Wire Fastener to Rear Panel. Tighten securely using the same screw. See _WIRE Fig.
Resumo do conteúdo contido na página número 17
Connecting A Liquid Propane Gas (LPgas) Figure 17a (LP gas model only) Tank To Your Grill 1. Open the front Doors of cabinet. Pull out the LPG Tank Pull-out Tray. Place a 20 Ib tank with foot ring into the hole in the tray. See Fig.17a. Make sure the tank valve is in the OFF positon. 2. Align the tank so the Tank Valve faces the rear right corner of cabinet. Use the 51 16"x89mm Wing Bolt to secure gas tank from rear of tray.See Fig. 17a. 3. Check the tank valve to ensure it has proper external m
Resumo do conteúdo contido na página número 18
Connecting Natural Gas To Your Grill WARNING For Natural Gas grills: Connect the hose end of the 12 foot Natural Gas Hose to the Gas Mani- A strong gas smell, or the hissing sound of fold as shown in Fig.17c. Thread the 12 foot gas indicates a serious problem with your gas Natural Gas Hose through the hole of Rear Panel grill or the LP gas tank. Failure to immedi- to outside. Also read the natural gas safety ately follow the steps below could result in a instructions.(on page 4) fire or explosio
Resumo do conteúdo contido na página número 19
8, If the burner does not light, turn the Control Knob to OFF, wait 5 minutes for gas to clear, then retry. Basic Lighting Procedures 9. Once the left grill burner is ignited, the adjacent Machine oils used in the manufacturing process of burner can be lit by simply turning its Control Knob stainless steel can cause stainless steel to turn a tan to HIGH. color. Before initial grilluse, remove protective PVC film from Control Panel and inside and outside of Grill 10. Adjust Control Knobs to your
Resumo do conteúdo contido na página número 20
Manually Lighting Your Grill by Match • Misalignment of Ignitor on Burner Correction: Check for proper position of the To light your gas grill by match, insert a match into the Electrode Tip as shown in Figure 12 The gap Manual Lighting Stick and follow steps 1 through 6 of between the Spark Electrode Tip and Burner or the Basic Lighting Procedures. Then, light the match Spark Receiver should be approximately 3/16", and place Manual Lighting Stick through the Lighting Adjust if necessary. With t
