Resumo do conteúdo contido na página número 1
®
®
Aussie b by y M Me ec co o
LP Gas Grill
Assembly and Use Manual
TM
Joey
M MO OD DE EL L 7 71 11 10 0 S Se er ri ie es s L Li iq qu ui id d P Pr ro op pa an ne e G Ga as s G Gr ri illll
FOR OUTDOOR HOUSEHOLD USE ONLY. NOT FOR COMMERCIAL USE.
For Customer Service, call 1-800-251-7558 or visit our web site at www.meco.net
• Failure to follow these instructions could result in fire or explosion which could cause death,
serious personal injury, or property damage.
• Read and follow instr
Resumo do conteúdo contido na página número 2
— NOTICE — MECO CORPORATION STRIVES TO BE A QUALITY SUPPLIER OF CONSUMER PRODUCTS. IF WE OMITTED ANY PARTS NEEDED FOR ASSEMBLY, OR YOU NEED TROUBLESHOOTING INFORMATION, PLEASE CONTACT US USING OUR TOLL FREE NUMBER. THANK YOU FOR PURCHASING A MECO CORPORATION PRODUCT. 1-(800)-251-7558 CONSUMER SERVICE DEPARTMENT 8 am - 6 pm E.S.T Mon. - Fri. MECO CORPORATION 1-(423)-639-1171 (TELEPHONE) 1500 INDUSTRIAL ROAD www.meco.net 1-(423)-639-2570 (FAX) GREENEVILLE, TN. 37745 USA CONTENTS I. Assembly Inst
Resumo do conteúdo contido na página número 3
PARTS ILLUSTRATIONS If you need replacement parts, refer to the Parts Illustrations and the Parts List to find the exact parts you need. If you have any questions which require help, contact Customer Service and be sure to mention the model number of your grill. (3) Cylinder Retainer Clip (1) Owner’s Manual (4) Left Front Wheel Leg (2) Bottom Shelf (5) Left Rear Wheel Leg (8) Screw, M5x40mm (7) Right Rear Fixed Leg (6) Right Front Fixed Leg (9) Axle (13) Hood (11) Axle Spring Pin (12) Wheel Cove
Resumo do conteúdo contido na página número 4
(33) Handle Spacer (34) Handle Spacer (35) Hood Handle (Tapered) (Fitted) (36) Front Metal Panel (38) Flame Diffuser (37) Fabric Panel (39) Cooking Grid (42) Main Burner (40) Warming Rack (41) Main Burner Electrode (44) Control Panel (43) LP Cylinder w/Manifold and Heat Shield (45) Control Knob Regulator PARTS LIST ITEM DESCRIPTION PART # QTY. 1 Owner's Manual 03.6602.00 1 2 Bottom Shelf 03.6603.00 1 3 Clip, Cylinder Retainer 03.6205.01 1 4 Left Front Wheel Leg 1 03.6604.00 5 Left Rear Wheel Le
Resumo do conteúdo contido na página número 5
PARTS LIST (cont'd) 19 Sidebrace, Right 03.6615.00 1 20 Sidebrace, Left 03.6616.00 1 21 Screw, ST 4.0 x 10 03.6583.00 12 22 Bolt, M4 x 10 (Clear Nickel) 03.6267.00 2 23 Wingnut, M4 Solid (Left Sidebrace) 03.6313.00 2 24 Crossbrace, Rear 03.6617.00 1 25 Right Side Table Black 03.6618.00 1 26 Left Side Table Black 03.6619.00 1 27 Bolt, M6x15 03.6208.00 8 28 Bolt, M6x30 03.4129.00 2 29 Hood Heat Shield 03.6620.00 1 30 Spacer, M6x15mm (Deco Bar) 03.6621.00 2 31 Deco Bar 03.6622.00 1 32 Bolt, M6x60
Resumo do conteúdo contido na página número 6
To reduce the risk of a cut injury: · Wear protective gloves when handling parts that have sharp edges. · Some assembly may require help from another person. Observe where noted. TOOLS: and/or or STEP 1) Cart Assembly: (3) LP CYLINDER CLIP Attach the Legs to the Bottom Shelf with (8) M5 X 40 BOLT M5 x 40 Bolts threaded into the Bottom 8 PC Shelf holes. Position legs with the holes exactly as indicated . (2) BOTTOM SHELF 1 PC (4) LEFT FRONT (5) LEFT REAR WHEEL LEG WHEEL LEG (6) RIGHT FRONT (7) R
Resumo do conteúdo contido na página número 7
STEP 2) Assemble Axle, Wheels & Wheel Covers: Push Axle through center hole in Wheel and through lower hole in each leg. (FIG. 2A) Insert Axle pin through small hole in end of Axle until it snaps over it. (FIG. 2B) Align Wheel Cover pins with 3-holes in Wheel and push flush against Wheel. (9) AXLE 1 PC (11) AXLE PIN 2 PC (10) WHEEL (12) WHEEL COVER 2 PC 2 PC (10) WHEEL (9) AXLE (12) WHEEL COVER WHEEL LEGS FIG. 2A (11) AXLE PIN FIG. 2B 7
Resumo do conteúdo contido na página número 8
Step 3) Assemble Hood/Bowl to Cart: (16) M6 LOCKNUT 4 PC (15) BOLT, M6X45 4 PC Bowl Bracket Legs (14) HOOD/BOWL ASSEMBLY Control Panel Bolt on each NOTE: REQUIRES 2-PERSONS side of grill · With Cart upright, align Bowl Bracket legs with Cart legs. (FIG. 3A) · Lower Hood/Bowl so ends of Cart legs insert into Bowl Bracket legs. · Press downward until leg screw holes align. NOTE: If cart legs do not align and fit into Bowl Bracket legs easily, loosen the Control Panel bolts slightly. Then o
Resumo do conteúdo contido na página número 9
Step 5) Assemble Sidebraces: · Attach Right and Left Sidebraces (19 & 20) to legs with ST4.0 x 10 Screws. (FIG. 5A) Secure Bottom Heat Shield to Left Sidebrace with M4x10 Bolts and M4 Wingnuts. (FIG. 5B) Allow Heat Shield Edge to overlap Sidebrace edge. (22) BOLT, (21) SCREW, ST4.0 x 10 M4x 10MM 4 PC 2 PC Heat Shield edge over (23) M4 WINGNUT Crossbrace (23) WINGNUT, M4 edge 2 PC (22) BOLT, M4x10MM FIG. 5B (20 Left Sidebrace (21) Screw, ST4.0 x 10 (24) Rear CrossBrace (Pre-assembled) (19) Righ
Resumo do conteúdo contido na página número 10
Step 6) Assemble Side Tables: Align bracket holes of Left and Right Side Tables with holes in Bowl Leg Brackets. Attach Side Tables with M6 x 15 Bolts underneath. (FIG. 6A 7 6B) (25) RIGHT SIDE (26) LEFT SIDE TABLE TABLE (27) BOLT, M6X15 8 PC FIG. 6B (28) SCREW, M6X15 (27) BOLT, M6X15 FIG. 6A Step 7) Attach Deco Bar and Hood Handle: Open Hood. Attach Deco Bar and Heat Shield with M6 x 30 Bolts through the Heat Shield and Hood. Do not tighten completely. Attach Hood Handle, Tapered Spacer and
Resumo do conteúdo contido na página número 11
Step 8) Attach Front Panels: Eyelet fits over Place Lower Metal Panel behind the Bolt and Nut front legs with short side to the right. Secure the 2-bottom screws. (FIG. 8A) Attach Top Fabric Panel to the top of FIG. 8B the legs. Position the eyelets over the bolt and nut on each side to align to align all attachment holes . (FIG. 8B) Secure Fabric Panel to holes in the legs over the eyelets. Over lap bottom of Fabric Panel to Metal Panel, then secure (21) SCREW, ST4.0 x 10 with screws through b
Resumo do conteúdo contido na página número 12
OPERATING YOUR LP GAS GRILL · Never fill the LP gas cylinder more than 80% of CONNECTING/DISCONNECTING THE GAS cylinder volume. (20 lb. maximum) Do not ask the propane supplier to over-fill the cylinder. USING GAS · If you obtain LP gas through a cylinder exchange dealer, make sure you get a safe and adequate O.P.D. cylinder. (See page 22) Use only a licensed LP gas cylinder dealer. CARBON MONOXIDE HAZARD · This appliance can produce carbon monoxide which · The LP gas cylinder, for use wit
Resumo do conteúdo contido na página número 13
6) Swing the Cylinder Retainer Clip over round shoulder of the LP cylinder. Exert pressure at Rotate ends of clip until it stops at the cylinder Cylinder carry handle. Cylinder Carry Handle Cylinder Retainer Clip FIG. 11A Cylinder Retainer Clip 4) Cut the tie clamp securing the regulator and FIG. 11D Hose to the burner tube. Disconnecting LP gas cylinder: 1) Turn all control knobs to the “off” position and turn the handle on the LP gas cylinder clockwise until it stops. 2) Turn coupling n
Resumo do conteúdo contido na página número 14
6) Check for leaks by brushing the soap solution SELECTING A LOCATION on all gas valves, hose connections and fittings. (shown by the heavy arrows in (FIG. 12A & 12B) To reduce the risk of serious bodily injury or death: Make sure you generously brush the locations · This outdoor cooking appliance shall be used only with the soap solution, completely surrounding outdoors and shall not be used in a building, garage, the connections and fittings. or any other enclosed area. Locate outdoor
Resumo do conteúdo contido na página número 15
To reduce the risk of serious bodily injury or death: · Open Hood before lighting the grill to prevent an explosion from any gas accumulation. · If lighting attempts fail, or the burners go out during operation, turn all control knobs “Off” to dissipate any accumulation of gas. Accidental ignition could occur. Wait five minutes before repeating lighting procedure. FIG. 13B · Light both left and right sides of burner to prevent gas from accumulating. LIGHTING THE GRILL USING THE IGNITOR 1. O
Resumo do conteúdo contido na página número 16
MANUAL LIGHTING THE GRILL Manual Lighting Hold flame near Burner. To reduce the risk of serious bodily injury or death: · Open Hood before lighting the grill to prevent an explosion from any gas accumulation. · If lighting attempts fail, or the burners go out during operation, turn all control knobs “Off” to dissipate any accumulation of gas. Accidental ignition could occur. Wait five minutes before repeating lighting procedure. FIG. 14B · Light both left and right sides of burner to preven
Resumo do conteúdo contido na página número 17
· Do not attempt to extinguish a grease fire with water WARMING RACK or other liquids. Have an BC fire extinguisher Warming racks are a convenient way to keep cooked food accessible. Do not douse or spray the grill or cooking warm or to warm items such as bread or rolls. When opening surfaces with water when hot. Burns from grease or the hood, be alert of dripping fat from the warming rack which the water splatters could occur. could then drip onto the barbecue causing a mess. Always · If you
Resumo do conteúdo contido na página número 18
CARE AND MAINTENANCE 4) Remove the two Burner screws from the bottom of grill Bowl. (FIG. 15C) Lift Burner out from the top of the grill. To reduce the risk of a cut injury: · Be careful or wear protective gloves when cleaning grill parts that have sharp edges. Heat Shield Screws CLEANING THE GRILL 1) Remove Drip Cup, Cooking Grid, and Flame Diffuser. Heat Shield 2) Drip Cup-Wash the Drip Cup with soap and water. 3) Grill Body and Cart-Remove excess grease and/or fat with a soft plastic or w
Resumo do conteúdo contido na página número 19
5) Use a pipe cleaner to clear insect nests from the inlet hole of main burner (FIG. 15D). Open up the main burner holes with a small nail or wire.Normal wear and corrosion may enlarge some holes, however, if large cracks or holes are found, replace the Burner. Use a brass wire brush to remove food particles and corrosion from the burner surface. (Note: It is normal for surface rust to be present on the burners.) It can be wire brushed and coated with cooking oil periodically. Verify that
Resumo do conteúdo contido na página número 20
TROUBLESHOOTING Possible Cause: Problem: Solution: Burner will not light Make sure burner tube is over the gas nozzle. See How to Clean Burner is not connected to using the ignitor the Burners #6 page 20: Re-install after cleaning. Valve. Not pausing long enough When lighting the Burner, push-in and turn control panel knob before clicking the Ignitor counter-clockwise to the high position. Pause 4 seconds, then Push in Ignitor button several times so that it clicks each time. No spark Gas colle
