Resumo do conteúdo contido na página número 1
CHAIN/BELT
GARAGE DOOR OPENER MODELS
IntelliG™1000/1200, SilentMax™1000/1200, ChainMax™1000/1200
OPERATION & MAINTENANCE MANUAL
® ®
Includes INTELLICODE 2 Remote Control. Safe-T-Beam System must be installed to close door.
For use only with residential sectional or one piece overhead garage doors.
® ®
Homelink and Car2U compatible.
For Answers and Assistance:
1.800.354.3643
or visit www.geniecompany.com
WARNING: To reduce the risk of injury to persons or damage to property – Use this opener only
Resumo do conteúdo contido na página número 2
THIS PAGE LEFT BLANK
Resumo do conteúdo contido na página número 3
TABLE OF CONTENTS SAFETY INFORMATION Section ..............................................................Page OVERVIEW OF POTENTIAL HAZARDS Safety Information .................................................................... 2 READ THIS SAFETY INFORMATION Important Safety Instructions ..........................................2 CONVENTIONS USED IN THESE INSTRUCTIONS Safety Features / Opener Features .3 ................................ Garage doors are large, heavy objects that move with
Resumo do conteúdo contido na página número 4
SAFETY FEATURES OPENER FEATURES Safe-T-Beam® (STB) Non-Contact Reversing System INTELLICODE® 2 Access Security System Puts an invisible beam across the door opening. The door stops A new generation superior encryption system that enhances and reverses to the full open position if anything passes the securi ty of the door opener by continuously changing the through the beam. LED indicator lights on the powerhead and access code each time the remote is used. The door opener on the STBs prov
Resumo do conteúdo contido na página número 5
OVERVIEW OF POWERHEAD CONTROLS 1 Begin here ONLY AFTER This section describes the simple programming functions. Use this page to familiarize yourself with the completing assembly d an buttons and LED indicators used to program the opener. NOTE: These and buttons are for programming use installation of the opener. only. Do NOT use these buttons to operate the opener. There are three programming buttons and two lights Review the Assembly & (LEDs) on the powerhead. Each of the buttons ar
Resumo do conteúdo contido na página número 6
PROGRAMMING LIMITS FORCE CONTROL 2 ACTION INDICATION/RESULT WARNING 1 ON WALL CONSOLE Make sure doorway is in view and clear of obstacles and Press & Door fully closes. people to avoid injury or damage to property. Release DO NOT operate this unit from wall console before LIMITS Open/Close and FORCE are set. Severe damage to the opener can occur. button. The bullet MUST be engaged to carriage BEFORE setting limits. See Installation Poster (if provided) or call Customer S
Resumo do conteúdo contido na página número 7
PROGRAMMING REMOTES PROGRAMMING INTELLICODE® 2 REMOTES to New Intellicode® 2 Openers. to Intellicode® 1 (previous model) Openers. All type remotes program in the same way. The default setting of Intellicode® 2 must be changed. The LED color displayed on the remote indicates Bring remote(s) to powerhead location. For Car2U® and the IntelliCode® mode. HomeLink®, park car outside the garage with the ignition Red = IntelliCode® 1 / Green = IntelliCode® 2 key in the “ACCESSORY” position. Eac
Resumo do conteúdo contido na página número 8
OPTIONAL PROGRAMMING WALL CONSOLE - OVERVIEW This opener has a Serial Number sticker in which the serial IntelliCode® 1 or 2 wireless keypad numbers begin with 10 or higher. ACTION LED INDICATION/RESULT MODEL AC SR3 THE GENIE COMPANY FCC ID: B8Q AC SR3 Residential Door Operator 1 IC: 2133A-CSD1D 120V. 60HZ. 5A Enter your PIN S/N:10XXXX XXXXXXX on the wireless keypad. ROGRAM FOR H LP CAL 1-800-35GENIE OR WWW.GENIECOMPANY.COM 2 Press & Hold for Wall consoles f
Resumo do conteúdo contido na página número 9
Safe-T-Beam® (STB) SYSTEM CHECK MAINTENANCE & TROUBLESHOOTING 3 Check that both the RED and GREEN LEDs are ON steady. If you have any questions, please do not hesitate to This indicates the system is working properly. If both LEDs contact customer service at: 1-800-35-GENIE or visit are not ON steady, check the appropriate items below. www.geniecompany.com. – Check for obstruction. IMPORTANT SAFETY – Check alignment. INSTRUCTIONS – Verify wire routing from STBs to STB connection in power
Resumo do conteúdo contido na página número 10
CORRECTIVE MAINTENANCE CHAIN OR BELT - TENSION ADJUSTMENT WARNING Observe all safety warning and precautions! Disconnect power from opener and disconnect CHANGE LIGHT BULBS carriage in rail from bullet before beginning this WARNING task. Use extreme caution when working from a ladder Visually inspect the chain or belt every 6 months. or step stool. NOTE: Tension adjustments should be made with the When replacing light cover, make sure wires are door in the down position an
Resumo do conteúdo contido na página número 11
ADJUSTMENT GUIDE - FORCE SETTINGS ADJUSTMENT GUIDE - SPEED SETTINGS Speed settings are pre-programmed at the factory for the CAUTION maximum speed. Speed settings should not need adjustment with this unit. Door closing force is FACTORY set and requires no However, travel speed for the opener can be adjusted to a adjustment for normal operation. slower speed in both the open and close directions, To Never adjust the force settings to compensate for damage, mimimize wear on heavier se
Resumo do conteúdo contido na página número 12
FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM REFERENCE - CIRCUIT WIRING DIAGRAM Opener circuit wiring diagram. This wiring diagram is for reference only. Opening Cover May Cause Electric Shock. WARNING Disconnect power from opener prior to removing cover. POWER CORD CHAIN MOTOR SCREW DRIVE MOTOR CONNECTOR PRINTED CIRCUIT BOARD BLACK RED WHITE RED BLACK BLACK 12 3 4 GREEN STB BWC (IWC or AWC) 1 2 3 4 5 6 CHOKE STRIPED WHITE STRIPED WHITE WHITE BLACK SAFE-T-BEAM® WHITE BLACK (Purchased Separ
Resumo do conteúdo contido na página número 13
FOR HELP—1-800-35-GENIE OR WWW.GENIECOMPANY.COM TROUBLESHOOTING GUIDE - OPERATION PROBLEM WHAT TO DO Check power source, – Plug a lamp into outlet used for powerhead. If lamp works, power source is OK. – If not, check fuse or circuit breaker. Opener does NOT run If power is OK, from wall console. – Check connections at powerhead terminals and at wall console. – Limits must be set with door arm connected to door. Check if wall console Sure-Lock™ is ON. Turn Sure-Lock™ OFF & check operat
Resumo do conteúdo contido na página número 14
TROUBLESHOOTING GUIDE - POWERHEAD LEDs FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM Powerhead LED Possible Problem Solution Round LED Long LED Normal operation None required Check power supply OFF OFF No response from unit Contact a trained door system technician ON/RED/ ON/RED/ Limits NOT set properly Reprogram Limits, see page 5 STEADY STEADY Program error Unplug unit, wait 5 seconds, plug in ON/RED/ ON/RED/ Contact a trained door system FLASHING FLASHING Component failure technician ON/B
