Resumo do conteúdo contido na página número 1
Model ACA200
License Plate Rear Mounted Camera
With Wireless Receiving Module
Installation Manual
FEATURES:
● High Resolution: 1/4” CMOS Color Camera
● Compact Zinc Alloy Die Cast Body
● Waterproof Housing
● 130 Degree Wide View Angle
● Selectable Image: Normal/Reverse
● Wireless Transmitter
● Adjustable Camera Angle
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS 1. Warnings 2 2. Product Description 4 3. Packing List 5 4. Camera Installation 6 5. Wireless Receiver Installation 9 6. Camera Wiring Diagrams 11 7. Specifications 12 8. Troubleshooting 13 9. FCC Statement 15 1
Resumo do conteúdo contido na página número 3
Warnings This product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. Audiovox Elect
Resumo do conteúdo contido na página número 4
1. This product utilizes high voltage. Any unauthorized modifications or damage to the product may result in electrical shock. Handle all components with care. Inspect regularly for damage to components and cabling. 2. You are responsible for ensuring that the installation of this product does not void or affect the vehicle manufacturer’s warranty. Audiovox Electronics Corporation or its subsidiaries are not liable in full or in part for improper installation resulting in loss or damage t
Resumo do conteúdo contido na página número 5
Product Description This revolutionary camera design integrates a wireless backup camera with your vehicle’s rear license plate without covering the license plate. The camera is easy to mount on your car, truck, or van with the bracket being hidden by your license plate. This Wireless Camera transmits a signal using a 2.4 GHz frequency. Reception can be affected by use of other wireless products utilizing the same frequency, i.e. cell phones and Bluetooth products. Static or scrolling l
Resumo do conteúdo contido na página número 6
Packing List 1. CMOS Camera − 1 qty 2. Wireless Receiving Module − 1 qty 3. Theft-proof Screws: 2 each course thread and machine thread 4. Flat Washer, 6mm − 2 qty 5. Anti-Theft Allen Key − 1 qty 6. Wire connectors: a) Tap connectors-3 qty b) Ring connector-1 qty 7. Warranty Card 8. Owners Manual 5
Resumo do conteúdo contido na página número 7
Camera Installation NOTE: The transmitting antenna is located in the camera’s wire shielding. When installing the camera wire, straighten the wire for best transmission, allowing the monitor to receive the clearest image possible. DO NOT CUT THIS WIRE. 1. Remove the rear license plate to determine the best way to run the power wires to the reverse lights. 2. The camera cable can be routed through an existing grommet, or through a 5/8 inch hole drilled near the vehicle’s rear license pl
Resumo do conteúdo contido na página número 8
preventative. Route the camera cable connector through the hole and insert the grommet into the hole to prevent water from entering into the vehicle. 3. Place the camera bracket behind the license plate and line up the holes. Fasten the camera mounting bracket and the license plate to the vehicle using the anti-theft screws provided. After installation of screws with the tool provided, place the tool in the glove compartment or other safe place for future use. 4. Wire the Camera to the v
Resumo do conteúdo contido na página número 9
iv. Close the top hinged cover until latched. b) Attach the black wire to the ground. i. Place the un-stripped ground lead wire on the Tap/Run Connection run channel. ii. Insert the un-stripped black ground wire completely. iii. Fold the tap connector back over the wires and make the connection by crimping the u-contact down flush with the plastic insulator. iv. Close the top hinged cover until latched. c) Reverse/Normal Image Jumper: The blue jumper wire loop is located at the cam
Resumo do conteúdo contido na página número 10
Receiver Installation The receiver must be installed in the vehicle’s trunk or interior. The receiver are not weather proof and must be located in a dry location Tap/Run Connection 1. Wiring the receiver connection. a. Wiring the receiver to the vehicle. Choose a source that only has power when the vehicle is running. Connect as shown using the tap connectors supplied. i. Place the unstripped ignition source wire on the run channel ii. Place the unstripped red power wire completely.
Resumo do conteúdo contido na página número 11
connection by crimping the u-contact down flush with the plastic connector. iv. Close the top hinged cover until latched. b. Black wire-Chassis/Ground. Using ground ring supplied, i. Place stripped wire (1/4”) inside connector. ii. Crimp the connector using a crimping tool to secure the wire. iii. Connect to a vehicle body grounded screw (bare metal) directly. 2. Wiring the receiver to the monitor a. Connect the receivers RCA connector to the monitor RCA connector. 10
Resumo do conteúdo contido na página número 12
Camera Wiring (Color Camera View) Camera Wiring 11
Resumo do conteúdo contido na página número 13
Specifications 1. Voltage: DC12V 2. Operating Current: a. Transmitter: 130 mA b. Receiver: 180mA 3. Signal System: NTSC 4. Image Sensor: ¼” CMOS Sensor 5. Horizontal Resolution: 480 lines 12
Resumo do conteúdo contido na página número 14
6. Viewing Angle: 130 degrees 7. Minimum Illumination: 0.3Lux 8. Image Display: Selectable Normal/Reverse Image 9. Wireless Transmission Operating Frequency: 2.4GHz 10. Operating temperature: 0°C-50°C 11. Adjustable Viewing Angle 12. Camera Outer Dimensions: 25mm (W) x 30mm (H) x 62mm (D) Troubleshooting Symptoms Solutions 1. Check the rear view camera lens and clean if No video signal appears 13
Resumo do conteúdo contido na página número 15
needed. while reversing the 2. Check the rear view camera wiring and vehicle connection. Video image is not sharp Clean the camera lens. enough Symptoms Solutions The Monitor is not on Check the monitor and the receiver wiring and after the vehicle is started connection. and vehicle is in reverse? No video signal appears Check the rearview Camera wiring connection. while reversing the vehicle? 14
Resumo do conteúdo contido na página número 16
Video image is not sharp Clean the lens of the camera. enough? FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference, and b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for 15
Resumo do conteúdo contido na página número 17
compliance could void the user’s authority to operate the equipment 16
Resumo do conteúdo contido na página número 18
17 17
