Resumo do conteúdo contido na página número 1
Remote Start Keyless Entry
Model 1401
Owner’s Guide
© 2008 Directed Electronics, Vista, CA
G4102P 2008-09
Resumo do conteúdo contido na página número 2
Resumo do conteúdo contido na página número 3
Contents Government regulations .....................................................................................5 Warning! Safety first .........................................................................................7 What’s included ................................................................................................9 Important information ........................................................................................9 Your warranty.............................
Resumo do conteúdo contido na página número 4
Resumo do conteúdo contido na página número 5
Government regulations This device complies with Part 15 of FCC rules. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aga
Resumo do conteúdo contido na página número 6
This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept any radio interference that may be received, even if this interference could affect the operation of the device. Warning: Changes or modifications not expressly
Resumo do conteúdo contido na página número 7
Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed
Resumo do conteúdo contido na página número 8
Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in
Resumo do conteúdo contido na página número 9
What’s included • Two five-button/1-way Supercode remotes • The control module (installed out-of-sight) • Control center with integrated status LED and Valet override switch • A remote start defeat toggle switch • Window decals • Your warranty registration Important information Congratulations on the purchase of your state-of-the-art remote start and keyless entry system. Due to the complexity of this system, it must be installed by an authorized dealer only. Installation of this produc
Resumo do conteúdo contido na página número 10
+ + ➤ System maintenance The system requires no specific maintenance. Your remotes are powered by small coin cell lightweight 3-volt lithium batteries that last approximately one year under normal use. The remote uses one CR2032 cell battery. When the battery begins to weaken, the operating range is reduced. ➤ Low battery indicator When the batteries are low on the remote the vehicle system emits an addi- tional honk when unlocking to let you know its time to change the battery. Note: The op
Resumo do conteúdo contido na página número 11
+ + Detail 2. Turn both the unit front and circuit board over, remove battery from clip and replace. Note: Verify that the battery polarity is correct when replacing. 3. Reposition all parts and snap together. ➤ Two car operation You can use the remote control system for two cars, with full command capabil- ity for both vehicles. To change the car selection: A U X • Press and hold the button for 3 seconds until the amber LED blinks once or twice indicating the current vehicle: One blink:
Resumo do conteúdo contido na página número 12
8 6 1 2 7 9 3 4 5 1-way remote 1 6 2 7 3 4 5 6 Description Feature 1 Transmit indicator 2 Lock button Press for one second to lock. 3 Unlock Press for one second to unlock. button 4 Remote start Press for one second to activate remote button start. 5 Auxiliary Press and hold for 1.5 second to activate button optional trunk release. 7 1 6 Function button Allows access to programming and modi- fies operation of the other buttons. 2 8 3 Note: If Keypad Lock is On, press and th
Resumo do conteúdo contido na página número 13
A U X A U X A U X A U X ➤ Transmitter configuration Direct Access Level x 1 x 2 x 3 x 4 Button Lock Silent Lock Unlock Silent Unlock Valet Mode Car Finder Remote Start Reset Timer Mode Smart Start Rear A U X Runtime Defogger A U X A U X Trunk Release AUX 1 AUX 2 AUX 3 A U A U X X Function Shift © 2008 Directed Electronics. All rights reserved. 13
Resumo do conteúdo contido na página número 14
➤ Feature list Unlock Command: Press one time to Lock Notes: Press/hold for 1.5 seconds to lock the system and then activate the Panic output* Unlock A U X Command: Press one time to Unlock A U X Remote Start Command: Press one time to activate Remote Start A U X A U X Aux (trunk) A U X Command: Press and hold for 1.5 seconds to open trunk. Function shift Command: Press 1 to 4 times. ( See Function shift table) Notes: Each Press then release, shifts the function of the com
Resumo do conteúdo contido na página número 15
Runtime reset A U X A U X Command: Press one-time and then . Notes: Re-starts the remote start runtime counter if remote start is active. . Aux 1 A U X A U X Command: Press one time and then press . Notes: This is an optional feature. See your sales rep/installer for ALL details. A U X Valet mode Command: Press two-times and then . A U X Notes: Prevents the system from automatically activating the Failsafe Starter Kill and locking the door passively. A U X
Resumo do conteúdo contido na página número 16
A U X Smart start A U X Command: Press three-times and then press . Notes: Enables or disables the Smart Start feature. The parking lights flash fast 5 times when turning the feature on, and flash slowly 5 times when turning the feature off. A U X Aux 3 AUX Command: Press three times and then press . Notes: This is an optional feature. See your sales rep/installer for de- tails. A U X Rear defogger A U X Command: Press four times, and then . (after remote start is on.)
Resumo do conteúdo contido na página número 17
Using the system ➤ Locking the vehicle To lock the vehicle, press the button on the remote control. The horn in the vehicle “honks” one-time, and the parking lights flash one-time. If the power door locks have been connected, the doors lock. The system automatically checks for errors when it locks. If errors are found when locking: If the door is open when you lock the vehicle, the horn honks once and the parking lights flash. The horn then honks a second time to indicate that the door is
Resumo do conteúdo contido na página número 18
➤ Valet mode You can prevent your system from automatically activating the Failsafe® Starter Kill. When the system is in Valet mode, the feature is disabled. The doors do not automatically lock. This is useful when washing or having the vehicle serviced. To enter or exit valet mode with the valet/program switch: 1. Turn the ignition key on and then off. 2. At anytime during the next 10 seconds, press and release the Valet switch on the control center. The LED lights constantly if you have
Resumo do conteúdo contido na página número 19
➤ Remote feature programming The remote control has a menu for programming user features. Before you start make sure the keypad is unlocked. (See page 12) A U X To program the remote user features: 1. Press and hold the button on the remote for 12 seconds. (ignore the car indicator at 3 seconds). The remote transmit LED turns on solid to indicate the Main Menu. 2. Press and hold the button for 1.5 seconds: The remote LED blinks two-times. You are now in the Remote Configuration menu. F
Resumo do conteúdo contido na página número 20
➤ Overriding the optional starter kill To bypass the optional starter kill without a remote control: Use your override switch located on the control center (see diagram below) to bypass the system. This switch bypasses the system only if you have the vehicle key. To check proper operation: 1. While the vehicle is locked, open the door. Immediately insert the key into the ignition and turn it to the Run or On position. (all the indicators in the dash turn on) 2. Press and release the Override