Resumo do conteúdo contido na página número 1
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,AK-21W - LINEAR P/N: 228041 A - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1 - FOLDING: ALBUM-FOLD - BINDING: SADDLE-STITCH
AK-21W
Weather Resistant
Digital Keyless
Entry System
Installation and Programming Instructions
(760) 438-7000
USA & Canada (800) 421-1587 & (800) 392-0123
Toll Free FAX (800) 468-1340
www.linearcorp.com
228041 A IMAGE 1
Resumo do conteúdo contido na página número 2
CONTENTS FEATURES COMPONENT LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ✓ WEATHER RESISTANT DESIGN WIRING DIAGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 For outdoor installation INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 ✓ KEYPAD PROGRAMMABLE Opening the Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumo do conteúdo contido na página número 3
COMPONENT LOCATIONS MASTER CODE RED/GREEN YELLOW RESET JUMPER POWER/ACCESS "LOCKOUT" (JP2) INDICATOR INDICATOR TERMINAL BEZEL BLOCK #2 (TB2) SOLID STATE WHITE LED DOWN LIGHT TERMINAL BLOCK #1 (TB1) FACEPLATE KEYPAD BEEPER MOUNTING LEVEL PLATE JUMPER (JP1) Figure 1. Component Locations WIRING DIAGRAM TYPICAL DOOR INSTALLATION WIRING AK-21W TERMINALS TERMINAL TERMINAL BLOCK 2 BLOCK 1 12-24 VOLT 1 - AC OR DC SENSE - 8 POWER N.C. DOOR AC OR DC SUPPLY SWITCH 2 - AC OR DC COM - 7 POWER 3 - N.O. REQUES
Resumo do conteúdo contido na página número 4
Final Keypad Installation INSTALLATION After wiring the keypad (see next page), complete the installation Before installing the keypad, the unit must be partially disassembled by securing the keypad to the mounting plate. to access the mounting plate. ❑ If a lower beeper sound level is required, before installing Opening the Keypad the keypad, remove Jumper JP1 (place the jumper block on The keypad assembly is secured with two tamper-resistant screws. one pin to save the jumper). Refer to
Resumo do conteúdo contido na página número 5
Keypad Wiring 2 WIRES See Figure 7 for an example of a basic door installation. The DOOR FOR DOOR SENSE keypad is mounted adjacent to the door. An electric door strike SENSE SWITCH is mounted in the door jamb to release the door lock. A magnetic SWITCH switch is mounted on the top of the door jamb for detecting when the door is open. Use the following steps to wire the keypad. Refer to the wiring 2 WIRES diagram shown in Figure 8 to assist in the wiring. AK-21W FOR DOOR ☞ NOTE: Up to 500 fee
Resumo do conteúdo contido na página número 6
FACTORY DEFAULTS Adding a New Entry Code MASTER PROGRAMMING CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .123456 Press: 01 # Code # Code # Action # ENTRY CODE LENGTH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 DIGITS Code = The new entry code: 1-999999, depending on code length REQUEST-TO-EXIT OUTPUT RELAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .MAIN RELAY Action = Relay output entry co
Resumo do conteúdo contido na página número 7
PROGRAMMING OPTIONS Select Request-to-Exit Output Default: Main Relay There are several AK-21W programming options. For most Sets which output activates when the Request-to-Exit input is grounded. This output may be timed or toggled. installations, the factory set default options are suffi cient. The keypad must be in Programming Mode to make these changes. Press: 1 6 # Output # Select Door Sense or Inhibit Input Default: Door Sense Output = Output to Activate (0-4) The input on Terminal Block
Resumo do conteúdo contido na página número 8
AK-21W OPERATION Beep Sounds During Auxiliary Relay Default: No Selects whether or not the keypad beeps during Auxiliary Relay activation. Keypad users request access by entering their code. ❑ Users of the AK-21W have up to 40 seconds to key in their Press: 4 2 # Sound # entry code. Sound = 1 for Yes, = 0 for No ❑ Up to eight seconds are allowed between each keystroke. ❑ All digits of the entry code must be entered. Example: If the code is 0042, the user must enter Beep Sounds During Output #
