Resumo do conteúdo contido na página número 12
Connections PC Input Terminals connection (Female) COMPUTER Shared with DVI-D IN. Audio Stereo mini plug (M3) Connect a cable which matches the audio output terminal on the computer. Conversion adapter (if necessary) Mini D-sub 15p (Male) Notes: • Computer signals which can be input are those with a horizontal scanning frequency of 30 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. (However, the image will not be displayed properly if the signals exceed 1,200 lines.) • The display
Resumo do conteúdo contido na página número 13
Connections SERIAL Terminals connection The SERIAL terminal is used when the Display is controlled by a computer. COMPUTER (Male) RS-232C Straight cable (Female) D-sub 9p Notes: • Use the RS-232C straight cable to connect the computer 1 3 2 4 5 to the Display. 6 7 8 9 • The computer shown is for example purposes only. • Additional equipment and cables shown are not supplied with this set. Pin layout for SERIAL Terminal The SERIAL terminal conforms to the RS-232C interface Signal names for S
Resumo do conteúdo contido na página número 14
Power ON / OFF Connecting the AC cord plug to the Display. Connecting the plug to the Wall Outlet. Note: When disconnecting the AC cord, be absolutely sure to disconnect the AC cord plug at the socket outlet fi rst. Power switch Press the Power switch on the Display to turn the set on: Power-On. Power Indicator: Green Remote Control Sensor Power Indicator Press the button on the remote control to turn the Display off. Power Indicator: Red (standby) Press the button on the remote control to
Resumo do conteúdo contido na página número 15
Power ON / OFF When fi rst switching on the unit Following screen will be displayed when the unit is turned on for the fi rst time. Select the item with the remote control. Unit buttons are invalid. OSD LANGUAGE English (UK) OSD LANGUAGE Deutsch Français 1 Select the language. Italiano Español 2 Set. ENGLISH (US) Ру сский Notes: • Once the item is set, the screen won't be displayed when switching on the unit next time. • After the setting, the items can be changed in the following me
Resumo do conteúdo contido na página número 16
Selecting the input signal Press to select the input signal to be played back from the equipment which has been connected to the Display. Input signals will change as follows: HDMI PC* DVI HDMI: HDMI input terminal in AV IN (HDMI). PC: PC input terminal in PC IN. DVI: DVI input terminal in DVI-D IN. * “PC” may be displayed as “PC [YPBPR]” depending on the setting of “COMPONENT/RGB-IN SELECT”. (see page 35) Notes: • Selecting is also possible by pressing the INPUT button on the unit. • Select
Resumo do conteúdo contido na página número 17
Basic Controls Main Unit Power Indicator The Power Indicator will light. • Power-OFF .... Indicator not illuminated (The unit will still consume some power as long as the power cord is still inserted into the wall outlet.) • Standby ......... Red • Power-ON ...... Green • PC POWER MANAGEMENT .......................Orange (With PC input signal. See page 30) • DVI-D POWER MANAGEMENT .......................Orange (With DVI input signal. See page 30) Remote control Brightness Sensor se
Resumo do conteúdo contido na página número 1
Model No.
TH-42LF5U
TH-47LF5U
Operating Instructions
FULL HD LCD Display
Before connecting, operating or adjusting this product,
English
please read these instructions completely.
Please keep this manual for future reference.
Resumo do conteúdo contido na página número 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: To reduce the risk of electric shock, do not remove cover or back. No user-serviceable parts inside. Refer servicing to qualifi ed service personnel. The lightning flash with The exclamation point within arrow-head within a triangle a triangle is intended to is in tend ed to tell the user tell the user that important that parts inside the product operating and servicing are a risk of electric shock instructions are in the papers to per sons
Resumo do conteúdo contido na página número 3
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat. 9) Do not defeat the safety purpose o
Resumo do conteúdo contido na página número 4
Dear Panasonic Customer Welcome to the Panasonic family of customers. We hope that you will have many years of enjoyment from your new LCD Display. To obtain maximum benefit from your set, please read these Instructions before making any adjustments, and retain them for future reference. Retain your purchase receipt as well, and record the model number and serial number of your set in the space provided on the rear cover of these instructions. Visit our Panasonic Web Site http://pana
Resumo do conteúdo contido na página número 5
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee tha
Resumo do conteúdo contido na página número 18
Basic Controls Remote Control Transmitter OFF TIMER button The Display can be preset to switch to stand-by after a fi xed period. The setting changes to 30 minutes, ACTION button 60 minutes, 90 minutes and 0 minutes (off timer Press to make selections. cancelled) each time the button is pressed. ASPECT button 30 MIN 60 MIN 90 MIN Press to adjust the aspect. 0 MIN (see page 19) When three minutes remain, “OFF TIMER 3 MIN” will fl ash. Standby (ON / OFF) button The off timer is cancelled if a p
Resumo do conteúdo contido na página número 19
ASPECT Controls The Display will allow you to enjoy viewing the picture at its maximum size, including wide screen cinema format picture. Note: Be aware that if you put the display in a public place for commercial purposes or a public showing and then use the aspect mode select function to shrink or expand the picture, you may be violating the copyright under copyright law. It is prohibited to show or alter the copyrighted materials of other people for commercial purposes without the prior
Resumo do conteúdo contido na página número 20
Digital Zoom This displays an enlargement of the designated part of the displayed image. Display the operation guide. 1 EXIT Press to access Digital Zoom. The operation guide will be displayed. 1 During Digital Zoom, only the following buttons can be operated. [Remote control] POSITION / ACTION button Select the area of the image to be enlarged. 2 Press on the enlargement location to select. The cursor will move. EXIT 2 2 Select the magnifi cation required for the enlarged display. 3 Each time
Resumo do conteúdo contido na página número 6
Safety Precautions CAUTION This LCD Display is for use only with the following optional accessories. Use with any other type of optional accessories may cause instability which could result in the possibility of injury. (All of the following accessories are manufactured by Panasonic Corporation.) • Pedestal ................................................... TY-ST42P50 Always be sure to ask a qualifi ed technician to carry out set-up. Small parts can present choking hazard if accidentally
Resumo do conteúdo contido na página número 7
Safety Precautions WARNING Setup AC Power Supply Cord Do not place the Display on sloped or unstable The Display is designed to operate on 110 - 127 V AC, 50/60 Hz. surfaces, and ensure that the Display does not hang Ensure that the mains plug is easily accessible. over the edge of the base. Do not use any power supply cord other than that • The Display may fall off or tip over. provided with this unit. Do not place any objects on top of the Display. • Doing so may cause fi re or electric s
Resumo do conteúdo contido na página número 8
Accessories Accessories Supplied Check that you have the Accessories and items shown Operating CD-ROM Remote Control Transmitter Batteries for the Instruction book (Operating N2QAYB000691 Remote Control instructions) Transmitter (AA Size × 2) AC cord Remote Control Batteries Requires two AA batteries. 1. Pull and hold the hook, then 2. Insert batteries - note correct 3. Replace the cover. open the battery cover. polarity (+ and -). “AA” size - + + - Helpful Hint: For frequent remote control
Resumo do conteúdo contido na página número 9
Connections AC cord connection and fi xing AC cord fi xing Unplug the AC cord Unplug the AC cord pressing the two knobs. Plug the AC cord into the display unit. Note: Plug the AC cord until it clicks. AC cord When disconnecting the AC cord, be Note: (accessory) absolutely sure to disconnect the AC Make sure that the AC cord is locked on both the left and right sides. cord plug at the socket outlet fi rst. Video equipment connection AV IN AUDIO OUT HDMI Connect to sound HDMI Input Terminal
Resumo do conteúdo contido na página número 10
Connections AUDIO OUT connection Note: Additional equipment and cables shown are not supplied with this set. Stereophonic sound code audio equipment line-in HDMI connection [Pin assignments and signal names] Pin No. Signal Name Pin No. Signal Name T.M.D.S Clock 1 11 T.M.D.S Data2+ Shield T.M.D.S Data2 2 12 T.M.D.S Clock- Shield 3 13 T.M.D.S Data2- CEC 4 T.M.D.S Data1+ Reserved 14 T.M.D.S Data1 5 (N.C. on device) 19 3 1 HDMI cable Shield 6 15 T.M.D.S Data1- SCL 7 16 T.M.D.S Data0+ SDA T.M.D.S
Resumo do conteúdo contido na página número 11
Connections DVI-D IN connection PC with DVI-D video out Stereo mini plug (M3) Shared with PC IN. DVI-video cable with Ferrite core (Within 5 m) DVI-D Input Connector Pin No. Signal Name Pin No. Signal Name Pin Layouts T.M.D.S. data 2- 1 13 2 T.M.D.S. data 2+ 14 +5 V DC 3 T.M.D.S. data 2 shield 15 Ground Hot plug detect 4 16 1 8 5 17 T.M.D.S. data 0- 9 16 6 DDC clock 18 T.M.D.S. data 0+ DDC data T.M.D.S. data 0 shield 7 19 24 8 20 17 9 T.M.D.S. data 1- 21 Connection port view 10 T.M.
