Manual do usuário Metra Electronics 95-8210

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS FOR PART 95-8210
APPLICATIONS
Toyota 4-Runner Limited
2003-2009
95-8210
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double Din Trim Plate • B) Double DIN Brackets
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
A
• 70-1761 - Toyota harness 1987-up
• TYTO-01 - Toyota amp harness 2003-UP
Antenna Adapter:
• Not required
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips

Resumo do conteúdo contido na página número 2

95-8210 TABLE OF CONTENTS Dash Disassembly - Toyota 4-Runner Limited 2003-2009 . . . . . . . . . . . . . . . . . 1,2 Kit Assembly - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 *Note: Refer also to the instructions included with the aftermarket radio. K

Resumo do conteúdo contido na página número 3

95-8210 DASH DISASSEMBLY Toyota 4-Runner Limited 2003-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unsnap and remove trim from around shifter. (Figure A) 3 Unsnap and remove center console cover. (Figure B) B 4 Unsnap trim ring from around ignition key cylinder. 5 Remove (1) 10 mm bolt from bottom right side of panel below steering col- umn. Unsnap panel and pull away to gain access behind panel. (Figure C) C 6 Remove (1) 10 mm bolt on bottom left

Resumo do conteúdo contido na página número 4

95-8210 DASH DISASSEMBLY Toyota 4-Runner Limited 2003-2009 E 7 Remove (1) 10 mm bolt beneath cli- mate control behind pocket door. (Figure E) Unsnap climate control, unplug and remove climate control. (Figure F) 8 Remove (2) 10 mm bolts beneath radio behind climate controls. (Figure G) F 9 Unsnap and remove entire center panel around radio. 10 Remove (2) 10 mm bolts securing radio. Unplug and remove radio. (Figure H) Continue to final assembly. G H 2 PASSENGER

Resumo do conteúdo contido na página número 5

95-8210 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the factory brackets to the side of the radio. (Figure A) 2 Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure B) 3 Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) B Continue to final assembly. C 3

Resumo do conteúdo contido na página número 6

95-8210 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the factory brackets to the side of the radio. (Figure A) 2 Snap the Double DIN brackets to the outside edge of the Double DIN trim plate. (Figure B) 3 Slide the stacked ISO mount units into the bracket/trim plate assembly and secure the units to the assembly using the screws supplied with the units. (Figure C) B Continue to final assembly. C 4

Resumo do conteúdo contido na página número 7

95-8210 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D Locate the factory wiring harness in the dash. Metra recommends using the 1 proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. Reassemble radio and dash assemblies in reverse order of disasse

Resumo do conteúdo contido na página número 8

95-8210 INSTRUCTIONS www.metraonline.com 1-800-221-0932 REV. 06/03/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST95-8210