Resumo do conteúdo contido na página número 1
OPERATOR'S MANUAL
MU-170C OPERATOR'S MANUAL
Multi-purpose LCD Display
MU-170C
MU-170C
PUB.NO. OMC-20340-A1
(Elemental Chlorine Free) (0603,YOSH) MU-170C
The paper used in this manual
is elemental chlorine free.
Printed in Japan
Resumo do conteúdo contido na página número 2
IMPORTANT NOTICE • No part of this manual may be copied or reproduced without written permission. • If this manual is lost or worn, contact your dealer about replacement. • The contents of this manual and equipment specifications are subject to change without notice. • The example screens (or illustrations) shown in this manual may not match the screens you see on your display. The screen you see depends on your system configuration and equipment settings. • This manual is intended for
Resumo do conteúdo contido na página número 3
SAFETY INSTRUCTIONS Safety Instructions for the Operator Safety Instructions for the Installer WARNING WARNING Do not open the equipment. Do not open the cover unless totally familiar with Only qualified personnel electrical circuits and should work inside service manual. the equipment. Improper handling can result Do not disassemble or modify the in electrical shock. equipment. Turn off the power at the switchboard Fire, electrical shock or serious injury can before beginning the installation
Resumo do conteúdo contido na página número 4
TABLE OF CONTENTS FOREWORD ........................................................................................................ iii SYSTEM CONFIGURATION................................................................................ iv EQUIPMENT LISTS .............................................................................................. v 1. MOUNTING ....................................................................................................... 1 1.1 Display Unit......
Resumo do conteúdo contido na página número 5
FOREWORD A Word to the Owner of the MU-170C FURUNO Electric Company thanks you for purchasing the MU-170C 17” Multi-Purpose LCD Display. We are confident you will discover why the FURUNO name has become synonymous with quality and reliability. For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for quality and reliability throughout the world. This dedication to excellence is furthered by our extensive global network of agents and dealers. Your equipment is
Resumo do conteúdo contido na página número 6
SYSTEM CONFIGURATION RGB Radar, Video Plotter, Navigator, Video Sounder, Scanning Sonar, etc. DVI 12-24 VDC FAR-21X7 series, etc. VIDEO (NTSC/PAL) CCD camera, Video cassette recorder, etc. Connectable equipment Equipment Resolution Signal FCV-1200L/1200LM* VGA** Analog, via IF-8000 CH-250 VGA** Analog, via IF-8000 CH-270 VGA** Analog, via IF-8000 CSH-5L/8L XGA** Analog FSV-24/24S SXGA Analog GD-280/380/680 VGA** Analog FR-1500 MK3 series XGA** Analog FR-21X5 series SXGA Analog
Resumo do conteúdo contido na página número 7
EQUIPMENT LISTS Standard supply Name Type Code No. Qty Remarks Display Unit MU-170C - 1 w/hard cover Remote Controller Set* RMC-200 000-012-629 1 set Spare Parts* SP19-00401 001-416-700 1 set Installation Materials* CP19-00500 000-012-654 1 set Accessories* 1 set FP19-01001 001-416-740 *: See packing list of this manual. Option Name Type Code No. Qty Remarks 3COX-2P-6C 5M 000-146-500 1 Cable length: 5 m Cable Assy 1 Cable length: 10 m 3COX-2P-6C 10M 000-146-501 DVI-D/D SINGL
Resumo do conteúdo contido na página número 8
1. MOUNTING Refer to the outline drawing of this manual for mounting dimensions. Note: The face of the LCD monitor is made of glass. Handle it with care. 1.1 Display Unit The display unit may be mounted on a desktop (optional bracket kit required) or flush mounted in a panel. When selecting a mounting location, keep in mind the following points: • Locate the unit out of direct sunlight. • The unit weighs 7.5 kg (flush mounting) or 12.9 kg (desktop mounting). Be sure the mounti
Resumo do conteúdo contido na página número 9
Flush mounting See the outline drawing of this manual for mounting dimensions. CAUTION Hold the hard cover and display unit together when lifting the display unit. The display unit may fall out if only the hard cover is held. 1. Remove the hard cover and four cosmetic caps from the unit. 2. Using the paper template supplied, make a cutout in the mounting location. 3. Set the display unit to the cutout, and fasten it with four self-tapping screws (5x40, supplied as accessories). Not
Resumo do conteúdo contido na página número 10
Desktop mounting The display unit can be mounted on a desktop, using the optional bracket kit (Type: MU-170C Hanger, Code No.: 000-153-819). Contents of bracket kit Name Qty Hanger L 1 Hanger R 1 Pole 1 Hole plug 2 Hex bolt (M10x30) 2 Flat washer (M10) 2 Spring washer (M10) 2 Hex bolt (M5x25) 4 Flat washer (M5) 4 Spring washer (M5) 4 1. Assemble two hangers and pole with two hex bolts (M10x30), spring washers and flat washers, and cover holes for hex bolts with the hole plu
Resumo do conteúdo contido na página número 11
1.2 Remote Controller Setting battery 1. Open the back cover of the remote controller and set two batteries supplied. WARNING Ensure battery polarity is correct. Wrong polarity may cause the batteries to explode. 2. Close the back cover of the remote controller. Writing the device name on the label Write the device name (ex. “FCV-1200L”) for each “signal” name on the label supplied with the remote controller. Attach the label to the remote controller at the location shown below. RG
Resumo do conteúdo contido na página número 12
2. WIRING Connect external equipment to the MU-170C by referring to the drawing below, the table on the next page and the interconnection diagram in this manual. Note: The MU-170C does not have a “hot plug” function. Therefore, when the power switch of the MU-170C and the equipment connected to it are on, do not connect or disconnect the interconnection cable to prevent damage to equipment. ( )(+) Fuse Blue Red VIDEO3 TB-1 12-24 VDC VIDEO2 14AWG-2C-PVC *5M* (Supplied) CCD camera, VI
Resumo do conteúdo contido na página número 13
Port, cable and connectable equipment Used cable Port Connectable Standard/ Name Equipment Name Type Code No. Option Power 14AWG-2C-PVC TB-1 000-154-337 Standard Power source cable *5M* DVI DVI-D/D PC, DVI-D 000-149-054 Option Cable SINGLELINK5M FAR-21X7 series FCV-1200L/1200LM, 3COX-2P-6C CH-250, CH-270, RGB1 000-146-500 Option 5M CSH-5L/8L, Analog FSV-24/24S, RGB GD-280/380/680, Cable FR-1500 MK3 series, 3COX-2P-6C RGB2 000-146-501 Option FR-21X5 series, 10M NavNe
Resumo do conteúdo contido na página número 14
3. ADJUSTMENTS Adjust the MU-170C according to the equipment connected. 3.1 RGB/DVI Setting RGB1 and RGB2 screens can be adjusted independently. Also, DVI screen can be adjusted similarly. 1. Adjust the display currently selected, at the DISP selection window. (See section 4.3.) 2. Press the MENU key to show the main menu. The main menu disappears if there is no operation for one minute. 3. Press the ◄ or ► key to select RGB1, RGB2 or DVI as appropriate. The items on the RGB1 menu
Resumo do conteúdo contido na página número 15
Menu item Function Available range Adjusts the image size horizontally. H_SIZE Horizontal size: Narrow ( ◄) ↔ Wide ( ►) Variable depending on signal type Adjusts the image size vertically. V_SIZE Vertical size: Narrow ( ◄) ↔ Wide ( ►) Adjusts the timing of sampling so that the flicker PHASE** 1-32 disappears and the text is clear. Increases or decreases contrast level. CONTRAST 1-64 Dark ( ◄) ↔ Bright ( ►) Moves the image position horizontally. 1-99 (RGB1, 2), H_POSITION To
Resumo do conteúdo contido na página número 16
3.2 VIDEO Setting VIDEO1, VIDEO2 and VIDEO3 screens can be adjusted independently. The picture-in-picture window for each can be adjusted similarly. Also, the size of the picture-in-picture window can be adjusted at VIDEO1 (2 or 3) setting menu. Picture-in-picture window Picture-in-picture window 1. Set to the display currently selected, at the DISP selection window. (See section 4.3.) 2. Press the MENU key to show the main menu. 3. Press the ◄ or ► key to select VIDEO1, VIDEO2 or V
Resumo do conteúdo contido na página número 17
3.3 Menu Window Setting 3.3.1 Adjusting the menu window The menu window can be moved and translucentized on the OSD (On Screen Display) menu. 1. Press the MENU key to show the main menu. 2. Press the ◄ or ► key to select OSD. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM H_POSITION 15 (1 – 29) V_POSITION 37 (1 – 37) TRANSLUCENT OFF (OFF/ON) PIP SW TIME OFF (OFF, 5-20) PIP SKIP OFF (OFF, V1/V2/V3) CUSTOM NAME RGB1 = RGB1______ RGB2 = RGB2______ DVI
Resumo do conteúdo contido na página número 18
3.3.2 Changing the signal name You can change the signal name which is shown on the DISP selection window (page 16) and PIP selection window (page 17). It is useful to use the name of the device connected (ex. “FCV-1200L”). 1. Press the MENU key to show the main menu. 2. Press the ◄ or ► key to select OSD. RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM Signal H_POSITION 15 (1 – 29) V_POSITION 37 (1 – 37) name area TRANSLUCENT OFF (OFF/ON) PIP SW TIME OFF (OF
Resumo do conteúdo contido na página número 19
3.4 Remote Controller Setting A remote controller can be set to be operative with a specific display unit, in the case of multiple MU-170C display units. It is useful to label the display unit and the corresponding remote controller with same name. 1. Press the MENU key to show the main menu. 2. Press the ► key to select SYSTEM. Remote controller ID square Display unit ID RGB1 RGB2 DVI VIDEO1 VIDEO2 VIDEO3 OSD SYSTEM INFRARED REMOTE A EXT BRILL CTRL OF
Resumo do conteúdo contido na página número 20
4. OPERATION 4.1 Controls Display unit DISP key Shows the DISPLAY selection window. MENU key Shows the main menu. Power key LED Optical sensor PIP key Arrow keys Shows the PIP selection window. Select menu item. BRILL key Shows the BRILL adjustment window. Display unit Power key Press the power key ( ) to turn the power on or off. Note: Even if the power switch is off, a small amount of current flows through the equipment. If the equipment won’t be used for a long time, turn off t
