Resumo do conteúdo contido na página número 1
GPS Chart Plotters
CP500
12" WAAS GPS Chart Plotter
Owner's Manual
Resumo do conteúdo contido na página número 2
WARNING!!! Electronic charts displayed by the GPS Chart Plotter are believed to be accurate and reliable, but are not intended to be a substitute for the official charts, which should remain your main reference for all matters related to the execution of safe navigation. For this reason we would like to remind you that you should carry on board and use the official published and approved nautical charts. FCC Compliance Statement This device complies with Part 15 of the FCC limits for Class
Resumo do conteúdo contido na página número 3
CAUTION - The GPS Chart Plotter is designed for maritime use. To avoid water intrusion ensure the C-MAP C-CARD door is completely closed. - Extensive exposure to heat may result in damage to the GPS Chart Plotter. - The GPS Chart Plotter contains dangerous high voltage circuits which only experienced technicians can handle. - STANDARD HORIZON will not be liable for errors contained herein, or for incidental or consequential damages in connection with the performance or use of this material. CLEA
Resumo do conteúdo contido na página número 4
Page 6 CP500
Resumo do conteúdo contido na página número 5
TABLE OF CONTENTS 1. INTRODUCTION ...................................................................................................... 11 1.0 GENERAL INFORMATION .................................................................................... 11 1.1 PACKING LIST ...................................................................................................... 11 1.2 OPTIONAL ACCESSORIES .................................................................................. 12 1.3 RADAR UNIT
Resumo do conteúdo contido na página número 6
6.0.3 Dynamic Nav-Aids ..................................................................................... 38 6.0.4 Safety Status Bar (DSI - Data Safety Indicator) ........................................ 39 6.0.5 Currents Prediction .................................................................................... 40 6.0.6 Pictures & Diagrams .................................................................................. 41 How to show the pictures or diagrams of a Multimedia Object.....
Resumo do conteúdo contido na página número 7
12.0.5 Customizing the Data Windows ................................................................ 65 12.1 NAVIGATION PAGE .............................................................................................. 66 12.2 HIGHWAY PAGE ................................................................................................... 66 12.3 CELESTIAL PAGE ................................................................................................. 67 12.4 GPS STATUS PAGE ..............
Resumo do conteúdo contido na página número 8
Page 10 CP500
Resumo do conteúdo contido na página número 9
1. INTRODUCTION Congratulations on your purchase of the CP500. Whether this is your first GPS Chart Plotter, or if you have other STANDARD HORIZON equipment, the STANDARD HORIZON organization is committed to ensuring your enjoyment of CP500. STANDARD HORIZON technical support personnel stand behind every product we sell, and our Product Support team invites you to contact us should you require technical advice or assistance, at 800/767- 2450, or marinetech@vxstdusa.com. 1.0 GENERAL INFORMATION T
Resumo do conteúdo contido na página número 10
1.2 OPTIONAL ACCESSORIES 1.3 RADAR UNIT SUPPLIED BY SI-TEX USA The Radar antenna will be supplied by SI-TEX in USA only and the part code is as follows: MODEL NUMBER DESCRIPTION MDS-1 2kW 24 Mile 12.4” diameter Radome antenna MDS-8 2kW 24 Mile 20” diameter Radome antenna MDS-9 4kW 36 Mile 23.5” diameter Radome antenna MDS-10-4 4kW 48 Mile 4Ft Open Array MDS-10-5 4kW 48 Mile 5Ft Open Array NOTE Please contact to the Standard Horizon Authorized dealer, STANDARD HORIZON technical support or SI-TEX
Resumo do conteúdo contido na página número 11
2. GETTING STARTED Through this manual you will see highlighted words. Please refer to the legend below: [MENU] If you see brackets around a bold and capital letter word this refers to a key press. [CHART] If you see brackets around a bold and small capital letter word this refers to a Soft Key press. GENERAL SETUP When a word(s) is bold capital letters and underlined, this refers to a menu selection item. 2.0 MOUNTING THE GPS CHART PLOTTER The CP500 is supplied with hardware for bracket or flu
Resumo do conteúdo contido na página número 12
2. Drill a hole in one area of the cutout area that will allow the blade of a jigsaw to be inserted. Insert and cut out the area on the panel using the jigsaw. 3. Next drill the four holes required to insert the GPS Chart Plotter with the mounting studs. 4. Install the mounting studs on the GPS Chart Plotter and insert into the mounting hole. 5. Attach the GPS Chart Plotter to the mounting location by attaching the supplied hardware to the mounting studs. 2.3 EXTERNAL GPS ANTENNA MOUNTING The CP
Resumo do conteúdo contido na página número 13
NOTE In some cases the screw may not be long enough, if this happens simply apply more RTV to the underside of the antenna to glue it into place. 2.3.1 GPS cable The following table is to be used as a reference. CONNECTOR, CABLE, FUNCTION 6pins Wire Color 1 1 RED +10-35 Vdc 5 2 6 SMART GPS 2 GREEN GPS RX+ 4 SENSOR 3 3 BROWN GPS TX+ 6 BLACK/YELLOW/SHIELD GND/COMMON 2.3.2 GPS antenna connections 2.3.2.0 PWR & ACC 1 Cable BATTERY CONNECTIONS 1. The CP500 is supplied with a fuse and holder. This fus
Resumo do conteúdo contido na página número 14
NMEA CONNECTIONS The CP500 PWR ACC 1 connector is also used to attach NMEA devices such as AIS Receivers, digital instruments, Personal Computers, autopilots and the optional FF520 BOX FISH FINDER. *NOTE: AIS RECEIVER OPTION (for more information on AIS refer to Section 14) When an optional AIS receiver is connected, Port 1 of the NMEA In/Out Communication Setup menu must be changed to AIS 38400 as shown below for communications. 1. From the Chart page, press [MENU]. Move the ShuttlePoint knob t
Resumo do conteúdo contido na página número 15
**NOTE: FF520 FISH FINDER OPTION STANDARD HORIZON offers an optional BLACK BOX FISH FINDER called the FF520. When connected to the CP500, Port 2 of the NMEA In/Out Communication Setup menu must be changed to FF520 as shown below for communications. 1. From the Chart page, press [MENU]. Move the ShuttlePoint knob to highlight SETUP MENU and press [ENT]. 2. Move the ShuttlePoint knob to highlight ADVANCED SETUP and press [ENT] or move the ShuttlePoint knob to the right. 3. Move the ShuttlePoint kn
Resumo do conteúdo contido na página número 16
2.3.2.1 ACC 2 CONNECTOR This cable allows connections to a VHF, NMEA device with NMEA Output or the Input of the optional Radar antenna. *NOTE: RADAR Antenna connection (optional) When an optional Radar antenna is connected to the CP500, Port 5 of the NMEA In/Out is disabled. Contact Standard Horizon for details or refer the Radar Antenna’s manual for setup details. VHF Connections To connect the CP500 to the above VHF wires a port will be needed to be selected. Refer to the ACC 2 connections fo
Resumo do conteúdo contido na página número 17
· One VGA output Allows connection to a compatible TV or monitor using the optional VGAC10 adapter cable. · Two NTSC or PAL Video Inputs NTSC or PAL video inputs allowing a camera, DVD or VCR. To connect a video source use the optional ACVC10 cable (3 pin to RCA phone adapter). The CP500 has the capability to select the Video Input in three ways. a) From the menu 1. Press [MENU] twice and move the ShuttlePoint knob to highlight VIDEO INPUT and press [ENT]. 2. A menu appears with the following op
Resumo do conteúdo contido na página número 18
- If Auto Switch is chosen, all the menus will be closed and the video input will be shown switching between the Video Input Full View (if connected) and the selected page. See next section for details of setting up the switching times. If the user agrees to proceed, the image from the video input and the GPS Chart Plotter page will be shown intermittently. The intermittence time is selected by Switching Timeout item. . SWITCHING TIMEOUT, the possible choices are 5,10,30 sec, 1, 5, 10 min. Allow
Resumo do conteúdo contido na página número 19
3. CONTROLS AND INDICATORS 3.0 CONTROLS AND CONNECTIONS Using the keys located on the front panel controls the CP500. These labelled keys are dedicated to specific functions. As you press a key, a single audio beep confirms the key action; every time a key press is not valid, three rapid beeps sound to indicate that the key action is not valid. There is also a ShuttlePoint knob to move the cursor across the screen. The ZOOM IN and ZOOM OUT keys a. Pressing [ZOOM IN] shows more detail of a smalle
Resumo do conteúdo contido na página número 20
The MARK key Places a Mark under the ships position when in Home Mode, or when the cursor is shown will place a Mark under the location of the cursor. The ROUTE key a. When pressed places a Waypoint. b. Succeeding presses place more Waypoints to form a Route. The PWR key and Lamp/Contrast a. Press and hold [PWR] to turn the GPS Chart Plotter On or Off. b. Once On, press [PWR] momentarily, to show the Contrast and Lamp popup window. The MOB key When pressed the GPS Chart Plotter automatically pla
