Resumo do conteúdo contido na página número 1
Resumo do conteúdo contido na página número 2
TABLE OF CONTENTS INSTALLATION PREPARATION………………………………………………………. 2 Parts Supplied……………………………………………………………………. 2 Accessories………………………………………………………………………. 2 Installation Overview……………………………………………………………. 2 Alternative Transducers and Mounting Methods…………………………….. 4 Transducer Exchange…………………………………………………………… 5 INSTALLATION………………………………………………………………………….. 6 Transom Installation…………………………………………………………….. 6 Inside the Hull Installation………………………………………………………. 10 Control Head Installation…………
Resumo do conteúdo contido na página número 3
INSTALLATION PREPARATION PARTS SUPPLIED PARTS SUPPLIED Before installing your new Humminbird fishsinder, please ensure the following parts are included in the box: • Fishfinder • Transducer with 20’ (6m) of cable and mounting hardware kit • Mounting system and mounting hardware kit • 6’ (2m) power cable • Publications kit It any of these items is missing, call our Customer Support Hotline. ACCESSORIES Humminbird offers a wide assortment of accessories that complement
Resumo do conteúdo contido na página número 4
INSTALLATION PREPARATION INSTALLATION OVERVIEW Determining How to Mount the Transducer Your Humminbird fishfinder includes a standard transducer. This transducer can be mounted on the transom of the boat or bonded to the inside of a fiberglass hull boat. The transom installation, which is the most widely used, places the transducer on the outside of the boat hull. This technique produces the least signal loss, and provides a way to adjust the transducer after installation. The m
Resumo do conteúdo contido na página número 5
INSTALLATION PREPARATION ALTERNATE MOUNTING METHODS ALTERNATE TRANSDUCERS AND MOUNTING METHODS Your Humminbird fishfinder comes with everything necessary for installation and operation on most boats. However, there are several situations which may require a different type of transducer. Inboard boats, wood or metal hulls, and sail boats create unique transducer mounting needs Alternate transducers and mounting methods are detailed below. Portable Mounting The standard transducer
Resumo do conteúdo contido na página número 6
INSTALLATION PREPARATION TRANSDUCER EXCHANGE TRANSDUCER EXCHANGE Other transducers are available as replacements for the standard transducer. You may exchange your new and unassembled transducer for another type by returning it to the address listed in Customer Support. Some transducers may have additional cost. Refer to the Accessory catalog or call Customer Support for information. BEGINNING INSTALLATION Now that you have determined the transducer mounting method you can begin
Resumo do conteúdo contido na página número 7
INSTALLATION TRANSOM INSTALLATION Do not begin this transducer installation until you read the Installation Preparation in the Operation Guide. This chapter contains information critical to the correct installation of your transducer. Due to the wide variety of boat hulls, only general instructions are presented in the installation guide. Each boat hull represents a unique set of requirements that should be evaluated prior to installation. TRANSOM INSTALLATION Step One - Determi
Resumo do conteúdo contido na página número 8
INSTALLATION TRANSOM INSTALLATION • If the propeller(s) is (are) forward of the transom, it may be impossible to find an area clear from turbulence, and a different mounting technique or transducer type should be considered. Step Two - Drill the Mounting Holes 1. Remove the mounting template from the front of the Operations Manual. 2. Hold the template on the transom of the boat in the location where the transducer will be installed (Figure 4). Align the template vertically, ensu
Resumo do conteúdo contido na página número 9
INSTALLATION TRANSOM INSTALLATION Step Four - Mount the Transducer to the Transom 1. Apply silicone sealant to the mounting holes drilled into the transom. 2. Align the transducer assembly with the drilled holes in the transom (Figure 8). 3. Use either a flat head screwdriver, a 5/16" (8mm) hex driver, or a 5/16" (8mm) socket to mount the assembly. Using the two #10 – 1” (25mm) long slotted hex head screws, mount the transducer assembly to the transom as shown. Do not fully tight
Resumo do conteúdo contido na página número 10
INSTALLATION TRANSOM INSTALLATION Step Six - Route the Cable There are several ways to route the transducer cable to the to the area where the control head will be installed. The most common procedure routes the cable through the transom into the boat. Inside the boat there is often a channel or conduit used for other wiring that the cable can be routed along. Do not cut or shorten the transducer cable and try not to damage the cable insulation. Route the cable as far as practical
Resumo do conteúdo contido na página número 11
INSTALLATION INSIDE THE HULL INSTALLATION INSIDE THE HULL INSTALLATION Inside the hull installation requires the mount system and control head be installed and operational. See Installing the Control Head for instruction on installing the unit. Inside the hull mounting generally produces good results in single thickness fiberglass-hulled boats. Humminbird cannot guarantee depth performance when transmitting and receiving through the hull of the boat since some signal loss occur
Resumo do conteúdo contido na página número 12
INSTALLATION INSIDE THE HULL INSTALLATION 3. Power up the Control Head. 4. Run the boat at various speeds and water depths while observing the screen on the Control Head. If the unit functions well at low speeds but begins to skip or miss the bottom at higher speeds, the transducer needs to be moved. If depth performance is required, test the fishfinder in water at the desired depth. Test different locations in the hull until the optimum performance is achieved. Step Three - Perman
Resumo do conteúdo contido na página número 13
INSTALLATION CONTROL HEAD INSTALLATION CONTROL HEAD INSTALLATION Step One - Determine Where to Mount Begin the installation by determining where to mount the control head. Consider the following to determine best location: • The cables for power, transducer and temp/speed accessories (if applicable) should be installed first and must reach the mounting location. Extension cables are available. • There are two ways to route the cables to the unit: through a hole in the mountin
Resumo do conteúdo contido na página número 14
INSTALLATION CONTROL HEAD INSTALLATION and one amp fuse (not included) for the protection of the unit (Figure 21). Humminbird is not responsible for over voltage or over current failures. In order to minimize the potential for interference with other marine electronics a separate power source (such as a second battery) may be necessary. Step Three - Drill the Mounting Holes 1. Set the mounting bracket in place on the mounting surface. Mark the four mounting screw locations with
Resumo do conteúdo contido na página número 15
INSTALLATION CONTROL HEAD INSTALLATION Step Five - Assembling the Connector Holder 1. Insert the cable connectors into the connector holder. The cable connectors are labeled, and there are corresponding labels on the connector holder (Figure 26). The slots for the connectors are keyed to prevent reverse installation, so do not force the connector into the holder. 2. Carefully pull the excess cable from beneath the - mounting surface so the connector holder aligns with the mountin
Resumo do conteúdo contido na página número 16
INSTALLATION TEST THE INSTALLATION TEST THE INSTALLATION Testing should be performed with the boat in the water, however you can initially confirm basic operation with the boat trailered. Press POWER once to turn the unit on. There will be an audible chirp when any button is pressed to confirm the button press. If the unit does not power-up, ensure the unit is fully seated on the mount and that power is available. The first screen provides four options: Start-up, Options, Simulat
Resumo do conteúdo contido na página número 17
THANK YOU THANK YOU Thank you for choosing Humminbird, America’s #1 name in depth sounders. Humminbird has built its reputation by manufacturing top quality, thoroughly reliable marine equipment. Your Humminbird is designed for trouble-free use. We encourage you to read this operations manual carefully in order to get full benefit from your Humminbird and all its features and uses. Also, to register your purchase and ensure complete warranty coverage please take a few minutes to re
Resumo do conteúdo contido na página número 18
USING THE PLATINUM ID 120 HOW SONAR WORKS HOW SONAR WORKS There are two main components to a Platinum ID installation: the sensor, which you will install on the transom or inside the hull, and the Platinum ID unit. The sensor and Platinum ID communicate by means of a cable, and are powered by your boat’s 12-volt DC battery. The sensor and Platinum ID use the basic principles of sonar to reveal objects beneath the water’s surface. The Platinum ID continuously sends electronic sig
Resumo do conteúdo contido na página número 19
USING THE PLATINUM ID 120 HOW SONAR WORKS The Platinum ID uses the returned signals to display a detailed underwater image, and constantly updates the display as you travel across the water. The display informs you of the current depth and reveals individual fish, schools of fish, their location, bottom details as well as bottom hardness. An easy-to-use control also lets you enable a depth alarm for an audible alert when the boat is in shallow waters. The Platinum ID incorporates t
Resumo do conteúdo contido na página número 20
USING THE PLATINUM ID 120 PLATINUM ID FEATURES POWER: Press the button once to turn the Platinum ID on, then press again to turn the unit off. When the unit is off, keeping POWER pressed for about two seconds starts the built- in simulator. STOP: Freezes the action on screen so that it can be studied more closely or to allow more time to adjust menu functions. LIGHT: Activates the backlight for nighttime use. SELECT: Allows the user to select between menu functions that are d
