Resumo do conteúdo contido na página número 1
INSTALLATION INSTRUCTIONS FOR PART 99-8220
APPLICATIONS
Toyota
Tundra 2007-2011
Sequoia 2008-2011
99-8220
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• 99-8220 - Scratch Resistant Matte Black
• 99-8220HG - High Gloss Black
• 99-8220CHG - High Gloss Charcoal (matches 2010-UP models)
KIT COMPONENTS
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets
• E)
Resumo do conteúdo contido na página número 2
99-8220 TABLE OF CONTENTS Dash Disassembly - Toyota Tundra (Console Shift ) 2007-2011 . . . . . . . . . . . . 1,2 - Toyota Sequoia 2008-2011 . . . . . . . . . . . . . . . . . . . . . . . . 1,2 - Toyota Tundra (Column Shift ) 2007 -2011 . . . . . . . . . . . . . 3 - Toyota Sequoia 2008-2011 . . . . . . . . . . . . . . . . . . . . . . . . 3 Kit Assembly - DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 - ISO Mount Radio Provision with Pocket. . . . . .
Resumo do conteúdo contido na página número 3
99-8220 DASH DISASSEMBLY TOYOTA TUNDRA (Console Shift) 2007-2011 TOYOTA SEQUOIA 2008-2011 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the top trim panel around cup holders. (Figure A) 3 Remove (1) Phillips screw from shifter trim panel and remove panel. (Figure B) 4 Unclip, unplug and remove the cli- mate control assembly. (Figure C) B Continue dash disassembly. C 1
Resumo do conteúdo contido na página número 4
99-8220 DASH DISASSEMBLY TOYOTA TUNDRA (Console Shift) 2007-2011 TOYOTA SEQUOIA 2008-2011 5 Remove (4) 10 MM bolts securing the D radio. (Figure D) 6 Unclip the right side of the instrument panel trim and pull back the trim,then unclip,unplug and remove radio. (Figure E) Continue to kit assembly. E 2
Resumo do conteúdo contido na página número 5
99-8220 DASH DISASSEMBLY TOYOTA TUNDRA (Column Shift) 2007-2011 TOYOTA SEQUOIA 2008-2011 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Remove (2) plastic Phillips screws one from each side of the trim panel below the cup holder then unclip and remove the panel. (Figure A) 3 Pull the cup holder out and depress the (2) clips on each side to slide cup holder out of cup holder panel. (Figure B) 4 Remove (4) Phillips screws from cup B holder panel assembly
Resumo do conteúdo contido na página número 6
99-8220 KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. A 1 Slide the DIN cage into the radio hous- ing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Snap the pocket into the radio housing. (Figure C) Continue to final assembly. B C 4
Resumo do conteúdo contido na página número 7
99-8220 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET *Note: Refer also to the instructions included with the aftermarket radio. 1 Mount the ISO Brackets to the radio using the screws supplied with the A radio. (Figure A) 2 Slide the radio into the radio housing until it snaps into place. (Figure B) 3 Snap the trim plate onto the front of the Radio/Housing assembly. (Figure C) 4 Snap the Pocket into the radio housing. (Figure D) Continue to final assembly. B D C 5
Resumo do conteúdo contido na página número 8
99-8220 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. (Figure C) B 4 Snap the Double DIN trim plate onto the front of the radio/h
Resumo do conteúdo contido na página número 9
99-8220 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Cut and remove the center bar from the radio housing. (Figure A) 2 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure B) 3 Slide the stacked ISO mount units into the bracket/housing assembly and secure the units to the assembly using the screws supplied with the units. (Figure C) B 4 Snap the Double DIN trim plate onto the front of the
Resumo do conteúdo contido na página número 10
99-8220 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
Resumo do conteúdo contido na página número 11
99-8220 NOTES 9
Resumo do conteúdo contido na página número 12
99-8220 INSTRUCTIONS 1-800-221-0932 www .metraonline.com REV. 11/22/10 © COPYRIGHT 2007-2010 METRA ELECTRONICS CORPORATION INST99-8220
