Manual do usuário Metra Electronics 99-7404

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS FOR PART 99-7404
APPLICATIONS
NISSAN
Maxima 2004-2006
99-7404
KIT FEATURES
ISO DIN Head unit provision
with pocket
KIT COMPONENTS
A) Radio Housing Panel • B) (4) Panel retaining Clips
B
A
TOOLS REQUIRED:
Phillips Screwdriver • Small Flat Blade Screwdriver
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION
JFLJKJK9E SAALSDKFJHJLAzD

Resumo do conteúdo contido na página número 2

99-7404 NISSAN MAXIMA Dash Disassembly ............................................................1-2 ISO DIN Head Unit Provision ................................................3 Final Assembly ....................................................................4 Notes ....................................................................................5 TABLE OF CONTENTS

Resumo do conteúdo contido na página número 3

DASH DISASSEMBLY 99-7404 2004-2006 NISSAN MAXIMA 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Twist and slide down the cover at the base of the shift knob. (Figure A) B 3 Remove the retaining clip at base of shift knob and pull up to remove. (Figure B) C 4 Unclip and remove panel surrounding shift knob. (Figure C) 5 Remove (2) Phillips screws at the bot- E tom of the radio panel and unclip and remove. (Figure E) 1

Resumo do conteúdo contido na página número 4

99-7404 F 6 Remove (2) Phillips screws at the bottom of the display panel and unclip and remove the panel. (Figure F) 7 Remove (4) Phillips screws to remove the audio/climate control/display as G one unit. (Figure G) 8 Remove (4) Phillips screws from each side of radio/tuner to remove from audio/climate control/display bracket assembly. H 9 Remove the (4) Phillips screws secur- ing the factory climate control button assembly to the radio panel and remove. Note: Retain all hardware to be used in

Resumo do conteúdo contido na página número 5

KIT ASSEMBLY 99-7404 ISO DIN HEAD UNIT PROVISIONS: A 1 Position the aftermarket radio into audio/climate control/dis- play bracket assembly and secure using the bottom (2) Phillips screw positions and the factory hardware. (Figure A) B Install the (4) supplied retaining 2 clips onto the 99-7404 in the same locations as the factory radio panel. (Figure B) C 3 Using the factory hardware secure the factory climate control button assembly into the 99-7404. (Figure C) D 4 Using the factory hardware

Resumo do conteúdo contido na página número 6

99-7404 A A) Strip wire ends back 1/2" B B) Twist ends together C) Solder C D) Tape D 1 Locate the factory wiring har- ness in the dash. Metra recom- mends using the proper mating adapter and making the con- nections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble in reverse order of disassembly using the 99-7404 instead of the factory rad

Resumo do conteúdo contido na página número 7

NOTES 99-7404 ____________________________________________________________ ____________________________________________________________ ____________________________________________________________ ____________________________________________________________ ____________________________________________________________ ____________________________________________________________ ____________________________________________________________ ___________________________________________________________

Resumo do conteúdo contido na página número 8

INST997404 1-800-221-0932 www.metraonline.com Rev. 06-15-07 © COPYRIGHT 2004-2007 METRA ELECTRONICS CORPORATION INST99-7404