Manual do usuário Metra Electronics 95-7861

Resumo do conteúdo contido na página número 1

INSTALLATION INSTRUCTIONS FOR PART 95-7861
APPLICATIONS
Honda Pilot
•2003-2005
•2006-2008 (Without Factory Navigation)
95-7861
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) “LX” Double DIN Trim Plate B) “EX” Double DIN Trim Plate C) Double DIN Brackets
A B C
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ • Panel Removal Tool
• Phillips Screwdriver • Socket Set
www.metraonline.com
1-800-221-0932
© COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORAT

Resumo do conteúdo contido na página número 2

95-7861 TABLE OF CONTENTS Dash Disassembly - Honda Pilot 2003-2005 ...... ........ ....... ........ ....... ...... 1 - Honda Pilot 2006-2008 (Without Factory Navigation) . . ............2 Kit Assembly - DIN Radio Provision ..... ........ ........ ....... ........ ... ..... . 3 - ISO Radio Provision ..... ........ ........ ....... ........ ... ..... .4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 *Note: Refer also to the instructions inclu

Resumo do conteúdo contido na página número 3

95-7861 DASH DISASSEMBLY HONDA PILOT 2003-2005 A 1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Using a small flat blade screw- driver remove the blank plate from upper right side of radio trim panel. (Figure A) Unsnap radio trim panel. Unplug 3 switches and remove panel. (Figure B) 4 Remove (4) 10mm bolts securing radio, unplug and remove radio. B (Figure C) Continue to kit assembly. C 1

Resumo do conteúdo contido na página número 4

95-7861 DASH DISASSEMBLY HONDA PILOT 2006-2008 (Without Factory Navigation) A 1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Remove (2) screws from the top of the instrument panel trim. Unclip and remove the instrument panel trim. (Figure A) Unclip and remove the left center trim 3 panel. (Figure B) 4 Unclip the radio trim panel. B Unplug and remove the panel. (Figure C) 5 Remove the (4) screws securing the radio. Unplug and remove the radio. (Figure D) Con

Resumo do conteúdo contido na página número 5

95-7861 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. NOTE: Select the proper radio housing for your vehicle. EX models use the (EX) Double DIN Trim Plate and LX models use the (LX) Double DIN Trim Plate. A 1 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure A) 2 Slide the Double DIN radio into the bracket/trim plate assembly and secure the radio to the assembly using the screws supplied wi

Resumo do conteúdo contido na página número 6

95-7861 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. NOTE: Select the proper radio housing for your vehicle. EX models use the (EX) Double DIN Trim Plate and LX models use the (LX) Double DIN Trim Plate. A 1 Snap the Double DIN brackets to the inside edge of the Double DIN trim plate. (Figure A) 2 Slide the stacked ISO units into the bracket/trim plate assembly and secure the units to the assembly using the screws sup- plie

Resumo do conteúdo contido na página número 7

95-7861 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Resumo do conteúdo contido na página número 8

95-7861 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 05/29/08 © COPYRIGHT 2004-2008 METRA ELECTRONICS CORPORATION INST95-7861