Resumo do conteúdo contido na página número 1
www.collegehillshonda.com
Accessory Application Publications No.
AII 37561-38377
2008 ACCORD
INSTALLATION
BACK-UP SENSOR
Issue Date
2-DOOR
INSTRUCTIONS
NOV 2007
PARTS LIST Control unit bracket (L4)
Back-up Sensor Attachment Kit
P/N 08V67-TE0-100A
Control unit
Control unit bracket (V6)
Beeper
13 Wire ties
4 Sensor clips
Wire tie with clip
Back-up sensor harness
2 Wire ties with holder
Back-up sensor subharness
2 Urethane tapes
Fuse label
© 2007 American Honda Motor Co., Inc. – All Rights Reserve
Resumo do conteúdo contido na página número 2
www.collegehillshonda.com Flange bolt, 6 x 12 mm TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 8 mm and 10 mm Socket Flange nut Pushpin Drill 3 mm Drill bit 24 mm and 26 mm Hole saw 4 Harness tapes Ruler Eye protection (safety goggles, face shield, etc.) 10 mm Combination wrench File Trim tool TN SILTRIMTL10 Accessory User’s Information Manual Illustration of the Back-up Sensor Installed on the Vehicle BUZZER CONTROL UNIT 2A FUSE CASE Back-up Sensor Kit P/N 08V
Resumo do conteúdo contido na página número 3
www.collegehillshonda.com 2. Disconnect the negative cable from the battery. 5. Remove the rear trim panel (five clips and three hooks). 3. Remove the two covers from the rear bumper and remove the rear bumper (two bolts, six self-tapping REAR TRIM PANEL screws, two clips, and unplug one connector). 4 CLIPS NOTE: Have an assistant help you remove the rear bumper. CONNECTOR 2 BOLTS 3 HOOKS CLIP 6. Fold down the rear seat back by pulling the lever under the rear shelf inside the trunk. 6 SE
Resumo do conteúdo contido na página número 4
www.collegehillshonda.com 8. Using the trim tool, remove the rear shelf access 10. Remove the left rear speaker (one bolt and panel, then release the front rear speaker retaining disconnect the vehicle connector). tab. BOLT LEFT REAR SPEAKER REAR SHELF ACCESS PANEL LEFT REAR SPEAKER COVER VEHICLE 7115040E CONNECTOR TRIM TOOL 11. Wrap urethane tape around the control unit at the (TN SILRIMTL10) area shown. Then, attach the control unit bracket into the control unit. L4 MODEL 9.
Resumo do conteúdo contido na página número 5
www.collegehillshonda.com L4 Model V6 MODEL • Loosen the upper bolt from the relay support. Remove the relay support (one bolt and 12. Install the control unit to the vehicle panel: disconnect the vehicle connectors). • Partially thread the 6 mm flange nut onto the control unit bracket stud. Insert the control unit BOLT bracket stud into the hole in the vehicle panel. (Loosen.) VEHICLE PANEL Tighten the 6 mm flange nut to secure the bracket
Resumo do conteúdo contido na página número 6
www.collegehillshonda.com 13. Attach the 2A fuse label to the fuse case on the 14. Disconnect the back-up light 2-pin connector from back-up sensor harness. the left taillight, and plug it into the back-up sensor harness 2-pin connector. Plug the remaining back-up sensor harness 2-pin connector into the left taillight. FUSE BACK-UP LIGHT CASE 2-PIN CONNECTOR LEFT TAILLIGHT BACK-UP HARNESS 2-PIN CONNECTOR BACK-UP 2A FUSE LABEL SENSOR HARNESS BACK-UP HARNESS CONNECTOR 742312A
Resumo do conteúdo contido na página número 7
www.collegehillshonda.com 15. At the left taillight, secure the back-up sensor V6 MODEL harness to the vehicle harness with one wire tie. VEHICLE HARNESS BACK-UP WIRE TIE VEHICLE SENSOR HARNESS HARNESS VEHICLE HARNESS BACK-UP SENSOR HARNESS GREEN TAPE 742314BE 16. Plug the back-up sensor harness 14-pin connector WIRE CONTROL TIE into the control unit, and route the harness forward UNIT along the vehicle harness. Secure the back-up CONTROL sensor harness to the vehicle ha
Resumo do conteúdo contido na página número 8
www.collegehillshonda.com 17. Secure the back-up sensor harness to the vehicle V6 MODEL harness with two additional wire ties at the locations shown. 2 WIRE TIES VEHICLE L4 Model HARNESS 2 WIRE TIES VEHICLE HARNESS WIRE TIE WIRE TIE BACK-UP SENSOR HARNESS VEHICLE BACK-UP SENSOR HARNESS HARNESS 771103BB VEHICLE BACK-UP HARNESS 742401CE SENSOR 18. Secure the back-up sensor harness clip to the hole HARNESS BACK-UP SENSOR in the vehicle panel. HARNESS VEHICLE BACK-UP SENSOR BACK-UP SENSO
Resumo do conteúdo contido na página número 9
www.collegehillshonda.com 19. Using scissors cut one urethane tape in half, and 23. Secure the beeper harness to the vehicle harness then cut one of the halves again. Wrap the cut pieces with one wire tie. around the beeper harness shown. 20. Install the connector clip to the beeper 2-pin connector. WIRE TIE VEHICLE HARNESS URETHANE BEEPER 2-PIN TAPE CONNECTOR BEEPER 2-PIN CONNECTOR CONNECTOR 2-PIN CONNECTOR CLIP (Wrap from the end of the 2-pin connector.) BEEPER HARNESS BEEPER
Resumo do conteúdo contido na página número 10
www.collegehillshonda.com 28. Install one wire tie with clip to the holder with the fuse case, and attach the wire tie to the vehicle harness. VEHICLE WIRE TIES HARNESS WIRE TIE VEHICLE WITH CLIP HARNESS FUSE CASE WIRE BACK-UP SENSOR TIE HARNESS VEHICLE GROMMET 761402AE 29. Remove the vehicle grommet from the rear panel. 30. Route the back-up sensor 6-pin connector through the hole in the rear panel, and seat the harness grommet in the rear panel hole. BACK-UP VEHICLE SENSOR HARNESS H
Resumo do conteúdo contido na página número 11
www.collegehillshonda.com 32. Install one wire tie with holder to the back-up sensor NOTE: There are several markings on the inside of the harness 16-pin connector, and attach the wire tie to rear bumper. Before piercing the rear bumper, verify you the vehicle harness. have the correct locations. BACK-UP SENSOR 3 MARKS 3 MARKS HARNESS WIRE TIE WITH 6-PIN CONNECTOR REAR BUMPER HOLDER PUSHPIN REAR BUMPER VEHICLE HARNESS MARK REAR BUMPER MARK PUSHPIN 742603BE 742410BE 33. Mark the inside
Resumo do conteúdo contido na página número 12
www.collegehillshonda.com 34. While wearing eye protection drill the rear bumper: • Using 26 mm holes saw, enlarge both lower in board bumper holes at the center of the bumper. NOTE: Center sensors are 26 mm holes, side sensors are Remove all burrs. 24 mm holes. • From the outside of the bumper, drill all eight pierced marks using a 3 mm drill bit. LOWER HOLE • Using a 24 mm hole saw, enlarge the lower HOLE outboard hole on the left side of the bumper. Remove all burrs. DRILL (
Resumo do conteúdo contido na página número 13
www.collegehillshonda.com 36. Install two center sensors into the 26 mm holes in the 2 BACK-UP SENSOR rear bumper using the sensor clips. Note the SUBHARNESS CLIPS direction and location for each sensor. SENSOR CLIP REAR BUMPER BACK-UP SENSOR SUBHARNESS SENSOR CLIP REAR BUMPER Outside Inside 2 CENTER HOLDER SENSORS CLIP (Blue) WIRE TIE 2 HOLES, WITH CLIP 742413BE 26 mm SENSOR CLIP 2 CENTER SENSORS (Blue) 37. Plug the four back-up sensor subharness 2-pin BACK-UP SE
Resumo do conteúdo contido na página número 14
www.collegehillshonda.com 41. Using isopropyl alcohol on a shop towel, clean the area where the harness tapes will attach. BACK-UP SENSOR BACK-UP SENSOR HARNESS SUBHARNESS 6-PIN CONNECTOR 6-PIN CONNECTOR 4 GREEN TAPES BACK-UP SENSOR SUBHARNESS CORNER SENSOR 4 HARNESS REAR TAPES LEFT BUMPER RIGHT CENTER CENTER CORNER SENSOR SENSOR SENSOR 761302AE 771107BB 42. At each green tape location, attach the back-up sensor subharness to the rear bumper with four harness tapes. 43. Plug
Resumo do conteúdo contido na página número 15
www.collegehillshonda.com 44. Check that all wire harnesses are routed properly and that all connectors are plugged in. 45. Reinstall all removed parts. 46. Reconnect the negative cable to the battery. 47. Enter the anti-theft codes for the radio and navigation systems (if equipped), then enter the customer’s radio presets. 48. Reset the clock. 49. Check that the back-up sensors work properly as described in the Accessory User’s Information Manual supplied. Beeper Volume Co
