Manual do usuário Honda Automobiles 08V03-S9A-101

Resumo do conteúdo contido na página número 1

Accessory Application Publications No.
AII 30556
AUTOMATIC DAY/NIGHT
INSTALLATION
MIRROR 2005-2006 CR-V
Issue Date
ATTACHMENT KIT
INSTRUCTIONS
SEP 2005
PARTS LIST TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Automatic Day/Night Mirror Attachment Kit
Flat-tip screwdriver
(sold separately)
P/N 08V03-S9A-101
Small flat-tip screwdriver
10 mm Combination wrench
Ratchet
Upper and lower covers
8 mm, 10 mm and 14 mm Sockets
T20 and T25 Torx bits
Diagonal cutters
Clip
Torque wrench
Isopropyl alcohol

Resumo do conteúdo contido na página número 2

3. Remove the lens from the roof console (four 5. Remove the mirror by sliding the mirror up. retaining tabs). ROOF CONSOLE MIRROR HOLDER RETAINING TABS (4) MIRROR 4130070H LENS 6. Remove the sunvisor holders. Turn the holder 90°, then pull it out. 4. Remove the roof console (four screws, and unplug one connector). CONNECTOR ROOF CONSOLE 4130081H SUNVISOR HOLDER 4130060H SCREW 2 of 10 AII 30556 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.

Resumo do conteúdo contido na página número 3

7. Remove the cap from the right sunvisor (four 10. Remove the passenger’s dashboard under cover retaining tabs). (release the three clips and two pins.) CLIPS (3) RETAINING TABS (4) PASSENGER’S CAP DASHBOARD UNDER COVER PINS (2) RIGHT SUNVISOR TORX SCREW 11. Open the glove box. Release the right and left 4130090H stops. 8. Remove the right sunvisor (two T25 Torx screws). TABS (2) 9. Remove the door opening weatherstrip from the STOPS (2) right front pillar in the area shown. Remove the right fr

Resumo do conteúdo contido na página número 4

13. Remove the right kick panel (pull to release the 15. Remove the driver’s dashboard lower cover: two clips). • Remove the fuse box lid, and open the pocket. • Remove the two self-tapping screws. RIGHT KICK PANEL • Gently pull out on the driver’s dashboard lower TAB cover to release the eight clips. If equipped, unplug the vehicle connector and remove the lower cover. VEHICLE CONNECTOR VEHICLE CONNECTOR (If equipped.) (If equipped.) DRIVER’S DASHBOARD LOWER COVER TAB CLIP POCKET HOOKS (2) 14.

Resumo do conteúdo contido na página número 5

17. Remove two self-tapping screws that fasten the 19. On M/T vehicles only, remove the four seat track heater A/C control panel to the dashboard. Pull end covers from the driver’s seat, then remove the the heater A/C control panel out toward you to four bolts that secure the seat. release the four clips. Unplug the vehicle connector, and remove the heater A/C control SEAT TRACK panel. END COVERS (4) DRIVER’S SELF-TAPPING SIDE SEAT SCREW HEATER A/C CONTROL PANEL VEHICLE BOLTS (4) CONNECTOR CLIPS

Resumo do conteúdo contido na página número 6

21. On M/T vehicles only, remove the two side covers 23. Slide the day/night mirror stay onto the mirror (four tabs) from the center console. holder, then tighten the T20 Torx screw installed on the day/night mirror. VEHICLE 2-PIN CONNECTOR CLIP TORX SCREW ILLUMINATION BULB Pull SIDE COVER MIRROR HOLDER TABS (4) MIRROR STAY CLIPS (2) DAY/NIGHT FRONT MIRROR CONSOLE TABS (4) SIDE 4404311T COVER CLIPS (2) 4130140H SELF-TAPPING SCREWS (7) 24. Plug the mirror harness 7-pin connector into the 22. On M

Resumo do conteúdo contido na página número 7

25. Route the mirror harness through the grooves of 28. Unplug the vehicle 21-pin connector (white) and the upper and lower covers. Attach the lower connect the day/night mirror harness 21-pin cover to the stay of the mirror. connectors between the vehicle 21-pin connectors (white). MIRROR ROOF LINING HARNESS LOWER VEHICLE 21-PIN COVER CONNECTOR (white) DAY/NIGHT MIRROR STAY UPPER AND LOWER COVERS DAY/NIGHT MIRROR 26. Slide the upper cover up and under the roof lining as shown. DAY/NIGHT MIRROR

Resumo do conteúdo contido na página número 8

31. Route the day/night mirror harness 4-pin connector 33. Route the day/night mirror harness ground terminal with fuse case upwards to the vehicle harness, to the right along the vehicle harness at the rear of and then along the vehicle harness to the fuse box the glove box frame. through the dashboard pocket opening. GLOVE BOX OPENING DASHBOARD DAY/NIGHT VEHICLE HARNESS POCKET OPENING MIRROR HARNESS FUSE CASE FUSE BOX INSTRUMENT PANEL DAY/NIGHT BRACKET MIRROR DAY/NIGHT DAY/NIGHT HARNESS MIRROR

Resumo do conteúdo contido na página número 9

35. Tape a piece of steel wire to the 4-pin connector 39. Secure the three clips from the day/night mirror end of the day/night mirror harness. Route the harness into the holes in the right front pillar. harness end up along the instrument panel side bracket, and out through the clearance between the right front pillar and the instrument panel as shown. DAY/NIGHT MIRROR HARNESS DAY/NIGHT MIRROR HARNESS CLIP 4-PIN CONNECTOR RIGHT FRONT PILLAR RIGHT FRONT PILLAR PIECE OF DAY/NIGHT INSTRUMENT STEEL

Resumo do conteúdo contido na página número 10

42. Secure the day/night mirror harness to the vehicle 44. Under the dashboard, secure the day/night mirror harness with four wire ties. harness to the vehicle harness with three wire ties. WIRE TIE VEHICLE HARNESS DAY/NIGHT MIRROR HARNESS DAY/ NIGHT MIRROR VEHICLE HARNESS HARNESS WIRE TIE 4202032H 43. Secure the day/night mirror harness to the vehicle harness with three wire ties. WIRE TIE 4202051H DAY/NIGHT MIRROR HARNESS 45. Check that all wire harnesses are routed properly and all connectors