Resumo do conteúdo contido na página número 1
Orbit 3
Orbit 3
Users Manual
www.microboards.com Version 1.01
Resumo do conteúdo contido na página número 2
Orbit 3 MICROBOARDS TECHNOLOGY, LLC 2
Resumo do conteúdo contido na página número 3
Orbit 3 MICROBOARDS TECHNOLOGY, LLC TABLE OF CONTENTS System Overview............................................................................................................................. 5 Unpacking your system ................................................................................................................... 5 Microboards Statement Regarding Improper Duplication .....................
Resumo do conteúdo contido na página número 4
Orbit 3 MICROBOARDS TECHNOLOGY, LLC 4
Resumo do conteúdo contido na página número 5
Orbit 3 MICROBOARDS TECHNOLOGY, LLC System Overview The Orbit 3 employs 2 general purpose DVD-+R/DL recorders, along with a single DVD reader. A hard drive also comes standard with the system, allowing for DVD/CD image archival and CD track extraction for CD audio compilations. An intuitive, menu driven display and 5-button control COPY START interface provide one-touch (DISC to DISC) operation for the no
Resumo do conteúdo contido na página número 6
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Installation Requirements System Setup • Connect the power cable to the Orbit 3 duplicator and plug in to a protected power outlet strip or UPS power supply. • Turn on power to the duplicator. • Install the Input Rods and Output Bin. The system is now ready to use. Install your Orbit 3 duplicator in the following environment: On a level and stable surface In a
Resumo do conteúdo contido na página número 7
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Orbit 3 Operation The Output Bin The Output bin should be installed prior to operating the Orbit 3. 1. Remove the 2 thumbscrews on the front of the Orbit 3. 2. Attach the Output Bin to the front of the Orbit 3 using the 2 thumbscrews. 3. Slide the Output Spindle into the Bin until the spindle locks against the vertical rods of the Output Bin. The feet of the spindle must be
Resumo do conteúdo contido na página número 8
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Main Menu The Up and Down Arrow buttons (▲▼) allow you to navigate through the menu without selecting the current menu item. The NO button will move you to the next menu item. YES will select the current menu item. YES Copy? (DISC to DISC) You will not be asked to load the master if you have a Hard Drive Partition selected NO, ▼ as the master source YES Quantity
Resumo do conteúdo contido na página número 9
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Disc-to-HDD Copy The number of partitions available will depend on the capacity of the hard drive installed in the Orbit 3. If your master is not already on the hard drive, please follow these steps. 1. Press NO or the up or down arrows until the display reads SYSTEM SETUP. Press YES. 2. The display will read DISC TO DISC; press NO. The display will read DISC TO HDD. 3. Press YE
Resumo do conteúdo contido na página número 10
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Copy & Compare Copy and Compare mode will run a comparison of the Master and the new copies prior to unloading the recorder drives. Like Copy mode, the source of the master will depend on the System Setup selections. The same steps are followed as with the standard Copy mode. Copies that do not pass the comparison will be rejected. Compare This function will run a comparison
Resumo do conteúdo contido na página número 11
Orbit 3 MICROBOARDS TECHNOLOGY, LLC 2. You will now select the hard drive partition to which you would like to save the extracted tracks. The display will show each partition on the hard drive in turn and what is saved on that partition. If any master data is already on the selected partition, it will be overwritten during the track extraction. In the top example to the right, hard drive partition 01 already contain
Resumo do conteúdo contido na página número 12
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Setup Menu Yes SYSTEM MASTER DISC TO HD? DISC TO HD? HD to DISC? DELETE? SETUP SELECT? Yes Yes Yes Yes Yes HD 1? HD 1? Yes Yes HD 2? HD 2? Yes Yes HD XX*? HD XX*? Yes Yes Both HD to DISC and DELETE * The number of hard drive options will only show those Hard partitions available will Drive partitions that contain data. depend on the capacity of BURN DISC? Answer
Resumo do conteúdo contido na página número 13
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Accessing the Setup Menu 1. At the COPY START? (DISC to DISC) menu, press the NO, ▼, or ▲ buttons until the display shows SYSTEM SETUP? SYSTEM SETUP? 2. Press the YES button 3. Pressing the NO or ▼ button will allow you to navigate through the menu. 4. Pressing the YES button will allow you to view or change the configuration of the system. 5. Please follow
Resumo do conteúdo contido na página número 14
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Drive Status This option allows you to disable a drive, if necessary. Any disabled drive will be bypassed during the duplication process; no discs will be loaded to or burned in a disabled drive. The recorder drives are numbered from the bottom up. There are 3 options: 1. Writer 1 ON / Writer 2 ON – this is the default setting, with both recorder drives active. 2. Writer 1 ON /
Resumo do conteúdo contido na página número 15
Orbit 3 MICROBOARDS TECHNOLOGY, LLC Technical Support For technical questions or support issues, contact Microboards Technology technical support: United States Europe Japan PH: 952-556-1639 PH: +44 (0) 845 230 7800 PH: 03-3561-2266 FAX: 952-556-1628 www.microboards.co.uk www.microboards.co.jp support@microboards.com www.microboards.com Please have the Model and Serial Number of your Microboards Product ava
Resumo do conteúdo contido na página número 16
Orbit 3 MICROBOARDS TECHNOLOGY, LLC 16
