Resumo do conteúdo contido na página número 1
User’s Manual
CoolCopyD1AL(DVD-Backup)
CoolCopyD 3
CoolCopyD 7
Resumo do conteúdo contido na página número 2
.Table of Contents Chapter 1 Introduction .................................................................4 1.1 Overview ....................................................................................4 1.2 Features .....................................................................................4 1.3 Specifications ............................................................................4 Chapter 2 Installation Procedure
Resumo do conteúdo contido na página número 3
4.11.7 Auto Compare ......................................................................20 4.11.8 Auto Prescan .......................................................................21 4.11.9 Eject Disc ............................................................................21 4.11.10 Burn on The Fly ................................................................21 4.11.11 Burn Mode ..............................................
Resumo do conteúdo contido na página número 4
Chapter 1 Introduction 1.1 Overview People who want to create multiple copies of their DVDs or CDs usually take a long time to do so. They might not have enough DVD+RW drives or they might be using their computers for some other important tasks. The duplication process noticeably slows down a computer during the burn process. Rather than sit at the computer for hours duplicating discs one at a time, it is much more efficient to use a CoolCopyD DVD/CD duplication system. The CoolCop
Resumo do conteúdo contido na página número 5
Writing mode - Auto Detect (DAO, TAO) Supported DVD-ROM Drive* - EPO, TEAC Supported DVD-RW Drive* - Plextor, TEAC, Lite-On, Asus, SONY Chapter 2 Installation Procedure When you purchase the CoolCopyD DVD Duplicator, the package may be packaged in the following ways: controller only, whole duplicator without writer installed or a complete duplication system. 2.1 Controller only 1. Before the installation, please prepare the necessary devices as following: · DVD-ROM dri
Resumo do conteúdo contido na página número 6
Hardware Connection with Hard Drive for CoolCopyD3 Coolcopy 3 IDE 3 DVD+/-RW IDE 2 DVD+/-RW IDE 1 DVD+/-RW IDE 0 DVD- Power When the system connects with the hard drive, the hard drive must connect on the IDE 0 port with the “Master” setting and the DVD-ROM must set at “Slave”. Hardware Connection without Hard Drive for CoolCopyD3 Coolcopy 3 IDE 3 DVD+/-RW IDE 2 DVD+/-RW IDE 1 DVD+/-RW IDE 0 DVD
Resumo do conteúdo contido na página número 7
Hardware Connection with Hard Drive for CoolCopyD7 Coolcopy 7 IDE 4 DVD+/- IDE 3 DVD+RW IDE 2 DVD+RW IDE 1 DVD- IDE 8 DVD+RW IDE 7 DVD+RW IDE 6 DVD+RW IDE 5 DVD+RW Power When the system has a hard drive connected, the hard drive must connect on IDE 0 port with “Master” setting and the DVD-ROM must set at “Slave.” Hardware Connection without Hard Drive for CoolCopyD7
Resumo do conteúdo contido na página número 8
Chapter 3 Key Functions and Operating Instruction 1. LCD Display Panel: Display main functions and all messages. 2. Scroll up through menus or functions. 3. Scroll down through menus or functions. 4. Execute the function which you select. 5. Cancel the function which you select. After turning the power on, the CoolCopyD DVD Duplicator will execute a self test for a few seconds. After the self testing procedure runs, the LCD will show: 1. CoolCopyD3:
Resumo do conteúdo contido na página número 9
· Failed discs will remain in writers. The default setting is to keep failed discs in the writers, but this can be changed. Press the buttons on the drivers to take the failed DVDs. · During the duplication process do not press any button because interruption will harm the device. DVDs will be damaged. 2. Without a hard drive installed If you don’t install a 3.5” hard disc, the operation procedures will be as follows: · Place the master disc in the DVD-ROM. · Switch to function 1, Copy
Resumo do conteúdo contido na página número 10
Function 2 Test will simulate the copying process. When the simulation completes, the discs will remain blank. Press ENT button to start the disc simulation. 2. Test If you use DVD rewriteable discs that contain data, the old Data will be quickly erased before simulation. The LCD will show the testing Testing-24X 0% Information as the following screen: 650.0MB 74:00 . When the process is finished, the LCD will show the message as the following screen: 2. Test OK: 0
Resumo do conteúdo contido na página número 11
4.5 Compare Function 5, Compare, allows you to make a comparison between the source and the target DVDs after copying. Select Function 5. Put the source DVD into DVD- 5. Compare ROM and the target DVDs into DVD writers. Press ENT to compare. LCD will show the Compare-24X 0% comparison information as the following screen: 650.0MB 74:00 When comparison completes, the LCD will show Compare OK: 3 as the following screen: Fail: 0 Diff: 0 Press ENT to see th
Resumo do conteúdo contido na página número 12
If the master disc cannot be read correctly, PreScan Fail! the LCD will show the following screen: 4.7 Disc Info Function 7, Disc Info, shows the basic information of the source DVD. Select Function 7. Place source DVD into DVD-ROM. 7. Disc Info Press the ENT button to show the disc information. The LCD will show the total sessions and Total 02 Sessions tracks on the master disc. Total 10 Tracks Press the ENT button again, the LCD will show Total: 74:00 the t
Resumo do conteúdo contido na página número 13
4.9.1 Load Place the master DVD disc into the DVD-ROM or any one of the DVD writers, the duplicator will detect and analyze the master DVD. Here the function “Load” will allow you to load data 9-01.Image P: A from the DVD-ROM or any DVD writer into the current partition of the hard disc. P:A means Partition A. Load Press ENT to load. The LCD will show the loading Load- A -24X 0% information. 650.0MB 74:00 When the image has successfully loaded, the LCD Image l
Resumo do conteúdo contido na página número 14
Press ENT again and use the arrow button Session 01 to select the session. The LCD will show the information Track 01 - 01 in the session. Press ENT again and use arrow button to select Track 01 the track. The LCD will show track information. DATA 650.0MB 4.9.4 Compare Image Use this function to compare the contents of the source DVD and those of the image file in the partition. First select the function by pressing the arrow. 9-04. Image P: A Press ENT and LCD will sh
Resumo do conteúdo contido na página número 15
Use the arrow button to select which partition will Select Working be worked. Partition - A When the partition is set, the LCD will show the Set Partition to following screen: A 4.9.6 Select Src Drive This function allows you to select the DVD-ROM or any DVD writer as the source from which you can load data into a particular partition as an image file. 9-06. Image P: A Press ENT and the arrow button to select the source. Image Src Drive Select Img Src: Then use
Resumo do conteúdo contido na página número 16
End edit disc Press ENT to finish the disc editing. Use the arrow button and burn?Yes to make “Yes” or “No” selection. The LCD will then show the following screen: Copying- 24X Edit 1/10 - > 1/1 When copying ends, the LCD will show the Burn Complete! following message: OK: 03 The system will ask if you want to continue editing. Use the arrow button to make a “Yes” or “No” selection Continue edit . next Disc?Yes Insert next disc If “Yes” is selected, t
Resumo do conteúdo contido na página número 17
4.10.2 CD to HDD This function lets you select one or more tracks from DVD-ROM and then copies into a certain partition of the HDD. 10-02. Edit Track Press ENT to enter the setting. CD to HDD Edit Follow the LCD to select the track that you want Select Track: to edit. Here 1/10 means the number one of 10 tracks 1/10 03:25 and 3:25 means the playing time. Press ENT button to select the track. After the Select Track: track is selected, the “+” will appear. Pressing
Resumo do conteúdo contido na página número 18
CD-R/RW or move into partition. Selecting “Burn” will Burn or Move to start the process. Partition?Burn The LCD will show the copying information as such: Copy- P0 -24X 0% 1/2 Trk03:25 When burning is finished, the LCD will show Burn Complete ! the following screen: OK: 03 Selecting Move will move the data from the hard drive template to a certain partition. Burn or Move to partition? Move Select the partition that the data will move into by Select Partition pr
Resumo do conteúdo contido na página número 19
Press ESC and the arrow to select the function. 10-04. Edit Track Close Session Press ENT. The system will ask whether you want to Close all disc’s close. After this step, the data cannot be written onto the disc. session? Yes Closing Session The LCD will show the message as the following screen: Please wait--- When you are finished closing the session, the LCD will Closing show the following message: Complete OK :3 Fail :0 4.11 Setup This function allo
Resumo do conteúdo contido na página número 20
speed then press ENT. The default is maximum. Other choices are 32X, 16X and 8X. 4.11.4 Auto Start Drive This function automatically tests or copies once you put the blanks discs into the writers. Press the ENT button to enter Auto Start Drive. 11-04. Setup Auto Start Drive Use the arrow button to change either the number or the “Off” setting. Then press ENT or ESC to Auto Start go back to the 11-04 menu. Drive Off 4.11.5 Start up menu This setting lets you select
