Resumo do conteúdo contido na página número 1
Z9 Commercial
Collection System
Operator and Parts Manual
Models: Z9A
Please read these instructions carefully and make
sure you understand them before using the machine.
Manual No. 200897 Rev. 02 (10-30-03)
Resumo do conteúdo contido na página número 2
INDEX Operators Guide Specifications .............................................................................................. 3 Features and Controls ................................................................................. 4 General Information ..................................................................................... 5 Safety Procedures ....................................................................................... 5 Unpacking Instructions ....................
Resumo do conteúdo contido na página número 3
SPECIFICATIONS Height 47 - 50 in. (119 - 127 cm.) Length 38 in. (97 cm.) Width (without hose or blower) 34.5 in. (94 cm.) Width (with hose and blower) 49 in. (124 cm.) Deck Options 42” 48” Weight (without spindle drive/blower assembly) 170 lb. (77 kg.) Weight (with spindle drive/blower assembly) 235 lb. (107 kg.) 3 Total Capacity
Resumo do conteúdo contido na página número 4
FEATURES & CONTROLS Exhaust Hood Inlet Arm Door Container Release Lever Upper Frame Lower Frame Hitch Bracket Hitch Drive Kit Hose Support Front Weight Hose Fan Front Weight Assembly Bar NOTE: Your Front Weight Bar and Hitch may look different from those shown in this diagram. 4
Resumo do conteúdo contido na página número 5
SAFETY RULES Safety Procedures General Information This manual will assist you in the safe operation 1 - Training: and proper maintenance of your Yazoo/Kees • Read the Operator’s manual. If the operator(s) equipment. Read it thoroughly before attempting or mechanic(s) can not read English it is the to operate the machine. Call your dealer or Yazoo/ owner’s responsibility to explain this material to Kees Customer Service if additional information them. is required. • Become familiar with the
Resumo do conteúdo contido na página número 6
SAFETY RULES 3 - Operation 4 - Maintenance and Storage: • Never run an engine in an enclosed area. • Stop engine and disconnect spark plug wire. • Only operate in good light, keeping away from Wait for all movement to stop before adjusting, holes and hidden hazards. cleaning, or repairing. • Slow down and use extra care on hillsides. • Clean grass and debris from muffler and engine Make turns gradually and at slow speed. Do to help prevent fires. Clean up oil or fuel sillage. not operate acros
Resumo do conteúdo contido na página número 7
ASSEMBLY Unpacking Instructions 1. Wear gloves and eye protection. Remove wood pieces. 2. Cut straps around carton and remove top. NOTE: Watch for nails and wood splinters. 3. Slide carton sleeve out of bottom tray and lift over Z9. Assembly Instructions Frame Assembly Lower Tools Required: Frame Upper 1. 3/4" wrench Frame 2. Ratchet 3. 3/4" socket 1. Position the Lower Frame inside the Upper Frame. 2. Align holes corresponding to
Resumo do conteúdo contido na página número 8
ASSEMBLY Mounting the Z9 NOTE: This portion of the assembly requires lifting the Z9; two people are required. Tools Required: 1. 9/16" wrench 2. Ratchet 3. 9/16" socket Upper Frame Hitch Hitch Bracket Lower Frame Wire Lock Pin 1. Install the Hitch from the Custom Kit accord- ing to the instruction sheet included in that carton. 2. Slide the Z9 into the hitch. 3. Line up holes in the Hitch and Z9 and se- cure with two (2) 3/8” wire lock pins. 4. Position the Hitch Brackets so
Resumo do conteúdo contido na página número 9
ASSEMBLY Spindle Drive & Drive Kit Assembly For use on mowers equipped with either a 12. Rest the fan assembly onto the deck end and 42", 48", 52" or 61" deck: slide the pilot thru the 5/8” hole previously mentioned so that fan assembly is supported by the pilot and the ¼” stop block welded under 1. Remove the discharge chute. the clamp at the front of the fan assembly. 2. Remove the right hand belt shield. Note: It may be necessary to swing the 3. Remove the deck belt from the right spindle i
Resumo do conteúdo contido na página número 10
ASSEMBLY Hose Trimming Tools Required: Utility Knife 3 Continue that cut through the webbing all the way around the hose so that it finishes just 1. Carefully measure the length needed. Re- across the support coil from where the member that although the hose is flexible, it original cut was started. will not stretch. 4. Use the utility knife to score the support coil 2. Measure the same length on the hose that between the beginning and end of the web needs to be trimmed, and with the utility
Resumo do conteúdo contido na página número 11
OPERATION Operating the Vacuum 1. NEVER USE THE Z9 WITHOUT ALL HOSES AND SHIELDS SECURELY AT- TACHED. 2. Make sure all hoses are connected at both ends. Inspect hoses prior to each use. 3. Do not use the Z9 on slopes greater than 15 degrees. 4. The mower must be running in order to vacuum debris through the mower deck. 5. In heavy grass it may be necessary to mow and vacuum at a slower ground speed. 6. Never attempt to unclog the Z9 until both the mower’s engine and vacuum’s engine have
Resumo do conteúdo contido na página número 12
SERVICE AND MAINTENANCE Transport For best results, clean exhaust screen inside container regularly. Instructions for doing this WARNING can be found in the Service section of this manual. The Z1-9 container must be completely empty while driving forward onto a trailer. If the Z1-9 must be loaded onto a trailer while there is still debris in the container, the mower must be backed up onto the trailer to avoid tipping. Storage 1. Refer to engine manufacturer’s instructions Cleaning and Washing f
Resumo do conteúdo contido na página número 13
SERVICE AND MAINTENANCE Caring For Vacuum Hoses Cleaning Exhaust Screen 1. Inspect hoses before each use. If hoses The exhaust screen on the Z9 is located inside have excessive wear, tears, or punctures, the container. For best results, clean exhaust replace immediately. screen regularty. 2. To prolong the life of the hose, periodically rotate hose and turn hose end to end. Refer Cleaning Instructions to Preventative Maintenance Schedule in this 1. Shut off all engines. manual. 2. Relea
Resumo do conteúdo contido na página número 14
SERVICE AND MAINTENANCE Troubleshooting Guide ! DANGER ! Before servicing unit wait for all moving parts to come to a complete stop. Turn engine off and remove the spark plug wire. PROBLEM POSSIBLE CAUSE CORRECTION Engine Does Not Start. 1. Spark plug wire disconnected. 1. Reconnect wire. 2. Engine ON/OFF switch in OFF position. 2. Put switch in ON position. 3. Fuel tank empty. 3. Add gasoline. 4. Stale gasoline. 4. Drain gasoline an
Resumo do conteúdo contido na página número 15
PARTS ILLUSTRATION 15
Resumo do conteúdo contido na página número 16
CONTAINER ASSEMBLY 27 26 2 24 16 28 1 11 4 6 12 18 7 15 8 13 3 17 4 25 12 8 17 10 9 23 19 20 14 7 21 5 22 17 16
Resumo do conteúdo contido na página número 17
CONTAINER ASSEMBLY ITEM PART NO. QTY DESCRIPTION 1 ........ 108970............ 1 ........ CONTAINER ASM. 2 ........ 200876............ 1 ........ EXHAUST ASM. 3 ........ 200691............ 2 ........ CLEVIS PIN 1/4 X 2 3/4 4 ........ ER99082 ......... 4 ........ HAIR PIN #13 5 ........ 200875............ 1 ........ DOOR ASM. 6 ........ 200692............ 2 ........ CLEVIS PIN 3/8 X 1 3/4 7 ........ 30425 ............. 4 ........ ROD END 8 ........ 200690............ 4 ........ PLUG
Resumo do conteúdo contido na página número 18
FRAME ASSEMBLY 19 17 18 16 14 11 15 9 13 12 2 8 11 10 7 3 6 5 4 6 1 20 7 ITEM PART NO. QTY DESCRIPTION 1 ........ 62072 ............. 1 ........ LOWER FRAME 2 ........ 200510 ........... 1 ........ UPPER FRAME 3 ........ ER99069 ......... 8 ........ BOLT, 1/2-13 X 1 1/4 4 ........ ER99020 ......... 4 ........ BOLT, 3/8-16 X 1 1/4 5 ........ ER93082 ......... 8 ........ NUT, 1/2-13, NYLOC 6 ........ 0415 ............... 8 ........ WASHER, 3/8 7 ........ ER99065 ......... 4 ........
Resumo do conteúdo contido na página número 19
HITCH & FRONT WEIGHT BAR ASSEMBLY 200209 ER99668 ER92731 200810 ER92531 FRONT WEIGHT QTY 2 INCLUDED WITH COLLECTION UNIT QTY 1 INCLUDED WITH CUSTOM KIT SEE INSTRUCTION SHEET INCLUDED WITH CUSTOM KIT FOR PARTS LIST. 19
Resumo do conteúdo contido na página número 20
SPINDLE DRIVE ASSEMBLY 19 5 22 28 21 23 7 1 20 6 27 24 39 2 23 14 27 21 4 40 10 46 36 42 9 37 35 25 11 13 33 14 26 44 18 34 30 8 46 28 31 29 8 32 45 43 12 15 41 17 15 16 27 38 28 29 28 29 3 20
