Resumo do conteúdo contido na página número 1
OWNER'S MANUAL
DC-1100A Dust Collector
JET P.O. BOX 1349 Phone:253-351-6000
WMH Tool Group Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.wmhtoolgroup.com e-mail jet@wmhtoolgroup.com M-708639 05/02
Resumo do conteúdo contido na página número 2
This manual has been prepared for the owner and operators of a JET DC-1100A. Its purpose, aside from machine operation, is to promote safety through the use of accepted correct operating and maintenance procedures. Completely read the safety and maintenance instructions before operating or servicing the machine. To obtain maximum life and efficiency from your dust collector, and to aid in using the machine safely, read this manual thoroughly and follow instructions carefully. Warrant
Resumo do conteúdo contido na página número 3
WARNING 1. Read and understand the entire contents of this manual before attempting assembly or operation. Do not use this machine until proper training and knowledge has been obtained. 2. Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before servicing. 3. Do not use outdoors or on wet surfaces. 4. Do not allow to be used as a toy. Close attention is necessary when used near children. 5. Use only as described in this manual. Use only manufactu
Resumo do conteúdo contido na página número 4
Grounding Instructions Caution: This tool must be grounded while in use to protect the operator from electric shock. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local co
Resumo do conteúdo contido na página número 5
230 Volt Operation If 230V, single phase operation is desired, the following instructions must be followed: 1. Disconnect the machine from the power source. 2. This dust collector is supplied with four motor leads that are connected for 115V operation, as shown in Figure A. Reconnect these four motor leads for 230V operation, as shown in Figure B. 3. The 115V attachment plug supplied with the dust collector must be replaced with a UL/CSA listed plug suitable for 230V operation. Co
Resumo do conteúdo contido na página número 6
On-Off Switch Padlock Model No. PB-1, Stock No. 709012 To safeguard your machine from unauthorized operation and to avoid accidental starting by young children, the use of a padlock is highly recommended. JET model PB-1 is available from your local authorized JET distributor or by calling JET Equipment & Tools at 800-274-6848. To lock out an on-off switch: 1. Open the padlock. See Fig. A. 2. Insert through holes in the start button. See Fig. B 3. Close the
Resumo do conteúdo contido na página número 7
Specifications: DC-1100A Stock Number................................................................................................................................ 708639 Blower Wheel Diameter........................................................................................................................11" Sound Rating at 3 feet................................................................................................................. 70-80 db Hose Diameter..................
Resumo do conteúdo contido na página número 8
WARNING Read and understand the entire contents of this manual before attempting assembly or operation of the dust collector! Failure to comply may cause serious injury! Unpacking 1. Finish removing all contents from the shipping carton. 2. Report any damage to your distributor. 3. Do not discard any shipping material until after the dust collector has been assembled and is running properly. Contents of the Shipping Carton 1 Bag Hanger 1 Base 1 Housing 1 Ha
Resumo do conteúdo contido na página número 9
Assembly 1. Install four casters to the under side of the base as pictured in Fig. 1. Thread the hex nut (B, Fig. 1) onto the caster shaft. Then slide the lock washer (A, Fig. 1) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug. Tighten the nut (B, Fig. 1) against the base with a 9/16” or 14mm wrench. This will give the caster proper clearance. 2. Place the base with casters on the ground. Attach the
Resumo do conteúdo contido na página número 10
4. Attach three support brackets (A, Fig. 4) to the base using six M8 x 16 hex cap bolts and six M8 flat washers (B, Fig. 4). Hand tighten only at this time. 5. Install the housing (A, Fig. 5) to two support brackets using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (B, Fig.5). Be sure hose opening faces fan housing. Before attaching third support bracket place the hanger bracket (C, Fig.5) between the support bracket and the
Resumo do conteúdo contido na página número 11
7. Slide the bag hanger hook (A, Fig. 7) through the top loop of the filter bag. Insert the hanger into the hanger bracket. Thread the retainer strap (B, Fig. 7) through the loops on the filter bag (C, Fig.7), and fasten to the collector housing. The retainer strap should be tight enough to provide a good seal. 8. Insert the ring (A, Fig. 8) of the collector bag into the bottom of the housing at an angle. Pull down on the bag to make sure it “seats” in the housing. Elect
Resumo do conteúdo contido na página número 12
5. Turn the bag outside in and insert into the Maintenance housing. WARNING Never perform maintenace on this machine Use the proper type hose to connect the dust before turning switch off and removing plug collector to the machine being operated. Dryer from power source, unplug. vent hose is not acceptable for this purpose. Failure to comply may cause serious injury! Contact your nearest JET distributor for the full line of JET Dust Collector Hoses and Accessories. Cust
Resumo do conteúdo contido na página número 13
Parts Breakdown 13
Resumo do conteúdo contido na página número 14
Parts List for the DC-1100A Index Part No. No. Description Size Qty. 1..........411035W ..................... Impeller Housing.................................... ...............................................1 2..........411026W ..................... Motor Bracket ........................................ ...............................................1 3..........998621......................... Strain Relief........................................... ...............................
Resumo do conteúdo contido na página número 15
Wiring Diagram 15
