Resumo do conteúdo contido na página número 1
US CA
part number 526607 N
05/2005
(page 1 of 12)
R
INSTALLATION INSTRUCTIONS
(NOTE: FOR INTEGRATED PANEL PREPARATION INSTRUCTIONS REFER TO SUPPLIED SHEET)
SINGLE DS603 MODELS
DOUBLE DD603 MODELS
DD603 PREFINISHED (shown left) DS603 PREFINISHED (shown left)
DD603 FLAT DOOR (not shown) DS603 FLAT DOOR (not shown)
DD603I INTEGRATED (shown right) DS603I INTEGRATED (shown right)
NOTE TO THE INSTALLER
WARNING!
Before installing the DishDrawer® , remove the house fuse or open
1. Read these instruct
Resumo do conteúdo contido na página número 2
R BEFORE YOU START - DOUBLE & SINGLE MODELS PARTS SUPPLIED DOUBLE MODELS SINGLE MODELS Phillips 16mm Wire Screws (5) Clip (1) Edge Flexible Extrusion Flexible Extrusion Protector (1) for Sides (2) Installation Tabs (2) for Top (1) Moisture Drain Hose Protection Clamp Support (1) Tape (1) Edge Protector (1) (1) Drain Hose Washer Phillips 16mm p/n 527208 Joiner (1) (1) Screws (7) Moisture Clamp (1) Washer (1) Flexible Extrusion for Sides (2) Protection Drain Hose Drain Hose Wire Tap
Resumo do conteúdo contido na página número 3
R DOUBLE MODELS SERVICES SPECIFICATIONS * WATER CONNECTION Recommended HOT ** # (Maximum 140°F/60°C). 3 Supplied hose to suit / ” (9mm) 8 male compression fitting. WATER SOFTENER MODELS Refer to your DishDrawer® User Guide for how to set up your water softener. WATER PRESSURE Maximum Minimum Water Softener Models 145 p.s.i. (1000kPa) 14.5 p.s.i. (100kPa) Prefinished model shown Other Models 145 p.s.i. (1000kPa) 4.3 p.s.i.
Resumo do conteúdo contido na página número 4
R DOUBLE MODELS PLUMBING OPTIONS OPTION 1 1 DishDrawer® and Standpipe Ø1 / ” (38mm) with Air Gap. 2 OPTION 2 DishDrawer® with Waste Disposal. OPTION 3 DishDrawer® using Air Break with Drain Hose Joiner. NOTE: Prefinished Model is shown. There is no variation in plumbing between models. Option 1 is the preferred option. Drains will need to be separated to satisfy Kosher requirements. We suggest you confirm acceptability with your local Rabbi in respect to Kosher installations. 4
Resumo do conteúdo contido na página número 5
R SINGLE MODELS SERVICES SPECIFICATIONS * WATER CONNECTION Recommended HOT (Maximum 140°F/60°C). ** 3 Supplied hose to suit / ”(9mm) male 8 compression fitting. WATER SOFTENER MODELS Refer to your DishDrawer® User Guide for how to set up your water softener. Maximum Minimum WATER PRESSURE Prefinished model shown Water Softener Models 145 p.s.i. (1000kPa) 14.5 p.s.i. (100kPa) *For an Integrated DishDrawer® the product depth is specified with an
Resumo do conteúdo contido na página número 6
R SINGLE MODELS PLUMBING OPTIONS OPTION 1 1 DishDrawer® and Standpipe Ø1 / ” (38mm) with Air Gap. 2 OPTION 2 DishDrawer® with Waste Disposal. OPTION 3 DishDrawer® using Air Break with Drain Hose Joiner. NOTE: Prefinished Model is shown. There is no variation in plumbing between models. Option 1 is the preferred option. Drains will need to be separated to satisfy Kosher requirements. We suggest you confirm acceptability with your local Rabbi in respect to Kosher ins
Resumo do conteúdo contido na página número 7
R INSTALLATION INSTRUCTIONS PLEASE NOTE: Your model of DishDrawer® may differ from the model shown in the installation READ THESE INSTRUCTIONS diagrams. Installation is similar for all models for either Single or Double models. Information referring COMPLETELY AND CAREFULLY. to Single models only is highlighted in blue. Installation diagrams have been simplified to enable clearer instruction. FOR INTEGRATED PRODUCTS FOLLOW THE INTEGRATED PANEL PREPARATION INSTRUCTIONS P/N 526608, BEFORE MOV
Resumo do conteúdo contido na página número 8
R INSTALLATION INSTRUCTIONS STEP 3: ADJUSTING THE FEET (DOUBLE MODELS ONLY) DOUBLE MODELS ONLY 10 Adjust the height of the product to suit the cabinetry, by turning the feet from inside the product using a wrench or M5 socket. TIP - gently take the load off each foot using the slide and then turn by hand. 3 / ” (5mm) 16 NOTE: For integrated products, the upper panel may be aligned with the top of the adjacent cabinetry, provided 3 a minimum / ” (5mm) clearance from the counter is 1
Resumo do conteúdo contido na página número 9
R INSTALLATION INSTRUCTIONS STEP 5: ELECTRICAL CONNECTION WARNING! WARNING! The product MUST NOT be If permanently connecting be plugged in at this stage. sure the power is isolated. 14 14 Be sure there is a power outlet in reach of the supplied power cord. If there is not a suitable outlet available then have one installed by a qualified electrician. Do not use an extension cord. This view shows the bottom left-hand rear corner with the cover removed Alternatively, the DishDrawer® may
Resumo do conteúdo contido na página número 10
R INSTALLATION INSTRUCTIONS STEP 7: CONNECTING THE DRAIN HOSE(S) DishDrawer® with Hose Joiner (see Plumbing Options). Remember to slip the wire clip(s) on the drain hose(s) first. 18a 18a Slip a wire clip over each drain hose, then push the hoses into the Drain Hose Joiner firmly, 5 clicks. Position the wire clip(s) between the two positioning ribs on the Drain Hose Joiner. Attach the Drain Hose Joiner to the waste tee (see Plumbing Options). Ensure a snug fit. If required a hose cla
Resumo do conteúdo contido na página número 11
R INSTALLATION INSTRUCTIONS STEP 9: MEASURING THE TOE KICK (DOUBLE MODELS ONLY) Partially open the bottom drawer. Turn Prefinished Toe Kick 21 upside down and hold vertically against the bottom edge of the Tub side (not the drawer front). Mark the position of the bottom edge of the Tub side on the Toe Kick. Choose the nearest groove to the pencil mark which will result in the shortest Toe Kick. 21 Bottom edge of tub side STEP 10: TRIMMING THE TOE KICK (DOUBLE MODELS ONLY) Important!
Resumo do conteúdo contido na página número 12
R INSTALLATION INSTRUCTIONS STEP 11: FITTING THE TOE KICK TO THE PRODUCT (DOUBLE MODELS ONLY) Toe kick mounting rails 25 Partly open bottom drawer. Position Toe Kick behind door and slide onto the mounting rails on the underside of tub. 25 Close bottom drawer, check if flush with adjacent cabinetry. 26 If required open drawer and adjust. Note: Clearance between Toe Kick and floor must be 15 / ” (12mm) minimum. 32 When Toe Kick is in position, open bottom drawer and gently fasten t
