Resumo do conteúdo contido na página número 1
US CA
part number 528247 B
master 526607 N
05/2005
(page 1 of 12)
R
INSTALLATION INSTRUCTIONS
SINGLE
DOUBLE
DD124 SERIES MODELS
DD224 SERIES MODELS
NOTE TO THE INSTALLER
WARNING!
Before installing the DishDrawer® , remove the house fuse or open
1. Read these instructions completely and carefully.
the circuit breaker. Ensure all water connections are turned OFF. It is
2. Installation of this DishDrawer® requires basic
the responsibility of the plumber and electrician to ensure that each
Resumo do conteúdo contido na página número 2
R BEFORE YOU START - DOUBLE & SINGLE MODELS PARTS SUPPLIED DOUBLE MODELS SINGLE MODELS Phillips 16mm Wire Screws (5) Clip (1) Edge Flexible Extrusion Flexible Extrusion Protector (1) Installation Tabs (2) for Sides (2) for Top (1) Moisture Drain Hose Protection Clamp Support (1) Edge Protector (1) Tape (1) (1) Drain Hose Washer Phillips 16mm p/n 527208 Joiner (1) (1) Screws (7) Moisture Clamp (1) Washer (1) Flexible Extrusion for Sides (2) Protection Drain Hose Drain Hose Wire Tap
Resumo do conteúdo contido na página número 3
R DOUBLE MODELS SERVICES SPECIFICATIONS * WATER CONNECTION Recommended HOT (Maximum 140°F/60°C). 3 Supplied hose to suit / ” male 8 compression fitting. WATER SOFTENER MODELS R Refer to your User Guide for how to set up your water softener. WATER PRESSURE Maximum Minimum Water Softener Models 145 p.s.i. (1000kPa) 14.5 p.s.i. (100kPa) * Depth of product excludes Other Models 145 p.s.i. (1000kPa) 4.3 p.s.i. (30kPa) 3 Curvature
Resumo do conteúdo contido na página número 4
R DOUBLE MODELS PLUMBING OPTIONS OPTION 1 1 DishDrawer® and Standpipe Ø1 / ” (38mm) with Air Gap. 2 OPTION 2 DishDrawer® with Waste Disposal. OPTION 3 DishDrawer® using Air Break with Drain Hose Joiner. NOTE: Prefinished Model is shown. There is no variation in plumbing between models. Option 1 is the preferred option. Drains will need to be separated to satisfy Kosher requirements. We suggest you confirm acceptability with your local Rabbi in respect to Kosher installations. 4
Resumo do conteúdo contido na página número 5
R SINGLE MODELS SERVICES SPECIFICATIONS * WATER CONNECTION Recommended HOT (Maximum 140°F/60°C). 3 Supplied hose to suit / ” male 8 compression fitting. WATER SOFTENER MODELS Refer to your DishDrawer® User Guide for how to set up your water softener. Maximum Minimum WATER PRESSURE Water Softener Models 145 p.s.i. (1000kPa) 14.5 p.s.i. (100kPa) * Depth of product excludes Other Models 145 p.s.i. (1000kPa) 4.3 p.s.i. (30kPa) 3 Curvature / ” (10mm) and
Resumo do conteúdo contido na página número 6
R SINGLE MODELS PLUMBING OPTIONS OPTION 1 1 DishDrawer® and Standpipe Ø1 / ” (38mm) with Air Gap. 2 OPTION 2 DishDrawer® with Waste Disposal. OPTION 3 DishDrawer® using Air Break with Drain Hose Joiner. NOTE: Prefinished Model is shown. There is no variation in plumbing between models. Option 1 is the preferred option. Drains will need to be separated to satisfy Kosher requirements. We suggest you confirm acceptability with your local Rabbi in respect to Kosher ins
Resumo do conteúdo contido na página número 7
R INSTALLATION INSTRUCTIONS PLEASE NOTE: Your model of DishDrawer® may differ from the model shown in the READ THESE INSTRUCTIONS installation diagrams. Installation is similar for all models for either Single or Double models. COMPLETELY AND CAREFULLY. Information referring to Single models only is highlighted in blue. Installation diagrams have been simplified to enable clearer instruction. STEP 1: MOVING THE PRODUCT INTO THE CAVITY MOUNTING TAB OPTIONS The mounting tabs are in pairs, on
Resumo do conteúdo contido na página número 8
R INSTALLATION INSTRUCTIONS STEP 3: ADJUSTING THE FEET (DOUBLE MODELS ONLY) DOUBLE MODELS ONLY 10 Adjust the height of the product to suit the cabinetry, by turning the feet from inside the product using a wrench or M5 socket. TIP - gently take the load off each foot using the slide and then turn by hand. 3 / ” (5mm) 16 NOTE: For integrated products, the upper panel may be aligned with the top of the adjacent cabinetry, provided 3 a minimum / ” (5mm) clearance from the counter is 1
Resumo do conteúdo contido na página número 9
R INSTALLATION INSTRUCTIONS STEP 5: ELECTRICAL CONNECTION WARNING! WARNING! If permanently connecting be The product MUST NOT be sure the power is isolated. plugged in at this stage. 14 14 Be sure there is a power outlet in reach of the supplied power cord. If there is not a suitable outlet available then have one installed by a qualified electrician. Do not use an extension cord. This view shows the bottom left-hand rear corner with the cover removed Alternatively, the DishDrawer® m
Resumo do conteúdo contido na página número 10
R INSTALLATION INSTRUCTIONS STEP 7: CONNECTING THE DRAIN HOSE(S) DishDrawer® with Hose Joiner (see Plumbing Options). Remember to slip the wire clip(s) on the drain hose(s) first. 18a 18a Slip a wire clip over each drain hose, then push the hoses into the Drain Hose Joiner firmly, 5 clicks. Position the wire clip(s) between the two positioning ribs on the Drain Hose Joiner. Attach the Drain Hose Joiner to the waste tee (see Plumbing Options). Ensure a snug fit. If required a hose cla
Resumo do conteúdo contido na página número 11
R INSTALLATION INSTRUCTIONS STEP 9: MEASURING THE TOE KICK (DOUBLE MODELS ONLY) Partially open the bottom drawer. Turn Prefinished Toe Kick 21 upside down and hold vertically against the bottom edge of the Tub side (not the drawer front). Mark the position of the bottom edge of the Tub side on the Toe Kick. Choose the nearest groove to the pencil mark which will result in the shortest Toe Kick. 21 Bottom edge of tub side STEP 10: TRIMMING THE TOE KICK (DOUBLE MODELS ONLY) Important!
Resumo do conteúdo contido na página número 12
R INSTALLATION INSTRUCTIONS STEP 11: FITTING THE TOE KICK TO THE PRODUCT (DOUBLE MODELS ONLY) Toe kick mounting rails 25 Partly open bottom drawer. Position Toe Kick behind door and slide onto the mounting rails on the underside of tub. 25 Close bottom drawer, check if flush with adjacent cabinetry. 26 If required open drawer and adjust. Note: Clearance between Toe Kick and floor must be 12mm minimum. When Toe Kick is in position, open bottom drawer and gently fasten the Toe Kick
