Resumo do conteúdo contido na página número 1
Controllers
INSTALLATION INSTRUCTIONS
WPK1, 4, 6 and 8
THE WATERPAD™
WATERPROOF PROGRAMMABLE KEYPAD SYSTEM
CD SAT
TNR
TNR
TUNER CATV
DISC
TAPE DVD
+ VOL
VOL
DISC
OFF
VCR1 VCR2
---
INTRODUCTION
THE WATERPAD™, an adaptation of the original Smart Pad ™ keypad system, is the world's first wall
2
mounted, fully programmable and configurable waterproof keypad. Now, outdoor, pool side, bathroom,
sauna and other high moisture installations can be handled with confidence. With the ease of the Dragon
D
Resumo do conteúdo contido na página número 2
• Two tiers of memory per button. Applies to both source select and control function buttons. • Sequence commands, including 1 to 30 second delays, can be programmed under any button (including the 2nd tier) without using up button spaces anywhere else on the keypad. • Status input permits source buttons to light with +12V representing a system power ON condition as well as the selected source. • Intelligent Power Management. The first command in a sequence, normally a power command, will not b
Resumo do conteúdo contido na página número 3
Controllers GUIDE MENU CD TUNER CD TUNER CH CH SAT CATV SAT CATV DISC MUTE TAPE DVD DISC LD DVD VOL CH VOL VOL OFF MUTE OFF TAPE VCR VOL CH WPK-6 WPK-8 This version has 14 function buttons and 6 source This version has 12 function buttons and 8 source buttons. Use this when you wish to control five or buttons. Use this when you wish to control seven six source components. or eight source components. INSTALLATION When installing the Waterpad, we suggest that you proceed with the followin
Resumo do conteúdo contido na página número 4
EMITTERS 789-44 CONNECTING BLOCK ® IR 12VDC RCVR The next step is to determine which Waterpad version and keypad button icons are required to perform this job, as follows: 1. Since there are 4 sources, 4 banks will be required. We will CD 1 TUNER TNR need the WPK-4 Waterpad version as shown in Fig. 1. TNR CD 2 TAPE PLEASE NOTE: All four versions of the Waterpad appear the same before the button Icons are applied. That is, all the AM MUTE FM VOL buttons in the right 2 columns have a small dark
Resumo do conteúdo contido na página número 5
Controllers 8. The Waterpad is now wired into the final system (refer to Figs. 3 & 5) and all commands tested again -- before applying the button icons. 9. If the system functions correctly, the button icons can then be applied, as shown in Fig. 4. Finally, the Waterpad is mounted to the wall as shown in Fig. 6, 7, 8 & 9. NOTE: The needed button icons are included with the Waterpad. Applying Icons To The Waterpad Buttons Each version of the Waterpad is supplied with 128 button icons on two my
Resumo do conteúdo contido na página número 6
Fig. 5 illustrates the terminal block, Six foot 7-Conductor Cable 8-Terminal Block STATUS JUMPER COM PORT adapter & the lead ter- (End of cable is not (use only if STATUS is waterproof-see text). mination legend for the Waterpad. not used. See "Power Spare terminal Management" below). THE WATERPAD™ (for future use) The 8-terminal block is included with (side view) +12V each Waterpad. The COM PORT (red) adapter is included with each DD4 GND (black) Dragon Drop-IR software package. STATUS (green
Resumo do conteúdo contido na página número 7
Controllers #6-32 x 1/2 Slot White • For retrofit (existing construction) appli- 1 Oval Hd Screw (4) #6-32 x 3/4 PH Flat Hd 3 Screw (4) cations, use high volume boxes, such "J"-Box 4 (Retro-Fit type) as the 2-gang Slater Retrofit 32 cu. inch box. Adapter Plate 5 • Most high volume new construction J- 2 boxes will work. A "P" ring could also be Water tight 9 CAUTION: 6 WATERPAD™ Pressure Relief Hole. See step 7 below. Decorator Style Unit used. Cover Plate (side view) #4-40 x 1/4 PH Pan Hd
Resumo do conteúdo contido na página número 8
9. The final step is to attach the Decorator Cover Plate (supplied) to the front of the Waterpad assembly using the four #6-32 x 1/2" Slot White Oval Hd screws (supplied). #6-32 x 1/2 Slot White 1 Oval Hd Screw (4) "J"-Box #6-32 x 3/4 PH Flat Hd 3 Mounting into a New Construction Screw (4) 4 (New Construction Type) J-Box The procedure to mount the Waterpad into a new construction type J-box is Adapter Plate 5 essentially the same as that for a retrofit 2 Water tight 9 CAUTION: 6 WATERP
Resumo do conteúdo contido na página número 9
Controllers TROUBLESHOOTING If you encounter problems, review each of the following items and take corrective action as described. If problems persist, contact Xantech Technical Support. 1. The Waterpad does not have RESTORE or CLEAR MEMORY buttons as does the SmartPad . How do I perform these functions on the Waterpad, if needed? 2 or 3 a) To perform the RESTORE function, simply remove the 12 VDC power from the unit for 10-15 seconds, then reapply. Programmed contents in the memory will not
Resumo do conteúdo contido na página número 10
Use these blank Waterpad panels when planning button layouts. 1-29-01 Rev.D 10 WPK1
