Resumo do conteúdo contido na página número 1
2. ERROR CODE AND SELF-DIAGNOSTIC MODE
2.1 Error Code List
The following error codes is displayed at the upper right of the screen when the CLEAR PAPER or CALL
2
SERVICE symbol is blinking.
2.1.1 Jam
Error code Classification Contents Troubleshooting
E010 Paper exit jam Jam not reaching the exit sensor : The paper which P. 5-1
has passed through the fuser unit does not reach
the exit sensor.
E020 Paper exit jam Stop jam at the exit sensor: The trailing edge of the P. 5-2
paper does not pas
Resumo do conteúdo contido na página número 2
Error code Classification Contents Troubleshooting E110 Paper misfeeding ADU misfeeding (Paper not reaching the registra- P. 5-3 tion sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing. E120 Bypass misfeeding (Paper not reaching the regis- P. 5-4 tration sensor): The paper fed from the bypass tray does not reach the registration sensor. E130 Upper drawer misfeeding (Paper not reaching the P. 5-5 upper drawer feed sensor): The paper fe
Resumo do conteúdo contido na página número 3
Error code Classification Contents Troubleshooting E210 Paper transport jam Lower drawer transport jam (Paper not reaching the P. 5-10 registration sensor): The paper does not reach the registration sensor after it has passed the upper drawer feed sensor. E220 Lower drawer transport jam (Paper not reaching the P. 5-11 upper drawer feed sensor): The paper does not reach the upper drawer feed sensor after it has passed the lower drawer feed sensor. 2 E300 PFP upper drawer transport jam (Paper
Resumo do conteúdo contido na página número 4
Error code Classification Contents Troubleshooting E550 Other paper jam Paper remaining jam on the transport path: The P. 5-19 paper is remaining on the transport path when print- ing is finished (caused by a multiple paper feeding). E712 RADF jam Jam not reaching the original registration sensor: P. 5-24 The original fed from the original feeding tray does not reach the original registration sensor. E713 Cover open jam in the read ready status: Jam P. 5-24 caused by opening of the RADF jam acc
Resumo do conteúdo contido na página número 5
Error code Classification Contents Troubleshooting EA10 Finisher jam Paper transport delay jam: The paper which has P. 5-30 (Finisher section) passed the bridge unit does not reach the inlet sensor. [MJ-1022/ 1023/1024/1101] EA20 Paper transport stop jam: P. 5-32 (1) The paper does not pass through the inlet sen- sor. [MJ-1022/1023/1024] 2 (2) The paper has passed through the inlet sensor but does not reach or pass the feed path sensor or processing tray sensor. [MJ-1023/1024] (3) The paper wh
Resumo do conteúdo contido na página número 6
Error code Classification Contents Troubleshooting EA80 Finisher jam Stapling jam: Stapling is not performed properly. P. 5-43 (Saddle stitcher sec- [MJ-1024] tion) EA90 Door open jam: The delivery cover or inlet cover P. 5-43 has opened dur-ing printing [MJ-1024]. EAA0 Power-ON jam: Paper exists at No.1 paper sensor, P. 5-44 No. 2 paper sensor, No.3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON. [MJ-1024] EAB0 Transport stop jam: The paper which passed P
Resumo do conteúdo contido na página número 7
2.1.2 Service call Error code Classification Contents Troubleshooting C010 Drive system related Main motor abnormality: The main motor is not P. 5-52 service call rotating normally. C020 Developer motor abnormality: The developer motor P. 5-52 is not rotating normally. 2 C030 Transport motor abnormality: The transport motor is P. 5-52 not rotating normally. C040 Paper feeding system PFP motor abnormality: The PFP motor is not rotat- P. 5-53 related service call ing normally. (the case that paper
Resumo do conteúdo contido na página número 8
Error code Classification Contents Troubleshooting C411 Fuser unit related ser- Thermistor or heater abnormality at power-ON: P. 5-60 vice call Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser roller does not rise in a specified period of time after power is turned ON. C412 Thermistor/heater abnormality at power-ON: Ther- P. 5-60 mistor abnormality is detected at power-ON or the fuser roller temperature does not rise within a spec- ified perio
Resumo do conteúdo contido na página número 9
Error code Classification Contents Troubleshooting CB10 Finisher related Entrance motor abnormality: The entrance motor is P. 5-67 service call not rotating normally. [MJ-1101] CB11 Buffer tray guide motor abnormality: The buffer tray P. 5-67 guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1101] CB12 Buffer roller drive motor abnormality: The buffer P. 5-67 roller drive motor is not rotating or the buffer roller is 2 not moving normally. [MJ-1101] CB20 Delivery
Resumo do conteúdo contido na página número 10
Error code Classification Contents Troubleshooting CBC0 Finisher related Alignment motor abnormality: Alignment motor is P. 5-72 service call not rotating or aligning plate is not moving normally. [MJ-1024] CBD0 Guide motor abnormality: Guide motor is not rotat- P. 5-73 ing or guide is not moving normally. [MJ-1024] CBE0 Paper folding motor abnormality: Paper folding P. 5-73 motor or paper folding roller is not rotating normally. [MJ-1024] CBF0 Paper positioning plate motor abnormality: Paper
Resumo do conteúdo contido na página número 11
Error code Classification Contents Troubleshooting CC71 Finisher related Punch ROM checksum error: Abnormality of check- P. 5-79 service call sum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1101 (when MJ-6101 is installed)] CC72 Punch RAM read/write error: Abnormality of check- P. 5-79 sum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1101 (when MJ-6101 is installed)] 2 CC80 Front alignment motor abnormality: Fro
Resumo do conteúdo contido na página número 12
Error code Classification Contents Troubleshooting CEA0 Copy process related Revolver home position detection abnormality: It P. 5-89 service call cannot detect that the revolver is at its home posi- tion. CEB0 Black developer unit lifting movement abnormality: P. 5-90 The black developer unit does not move up or down normally (lifting cam does not operate normally). CEC0 Copy process related 2nd transfer roller position detection abnormality: P. 5-91 service call The 2nd transfer roller does n
Resumo do conteúdo contido na página número 13
Error code Classification Contents Troubleshooting F110 Communication Communication error between System-CPU and P. 5-63 related service call Scanner-CPU F111 Scanner response abnormality P. 5-63 F120 Other service call Database abnormality: Database is not operating P. 5-97 normally. F130 Invalid MAC address P. 5-97 F200 Data overwrite kit (GP-1060) is taken off P. 5-98 2 F350 Circuit related service SLG board abnormality P. 5-65 call © June 2005 TOSHIBA TEC e-STUDIO281c/351c/451c ERROR CODE AN
Resumo do conteúdo contido na página número 14
2.1.3 Error in Internet FAX / Scanning Function 1) Internet FAX related error Error code Classification Troubleshooting 1C10 System access abnormality P. 5-98 1C11 Insufficient memory P. 5-98 1C12 Message reception error P. 5-98 1C13 Message transmission error P. 5-98 1C14 Invalid parameter P. 5-98 1C15 Exceeding file capacity P. 5-98 1C20 System management module access abnormality P. 5-98 1C21 Job control module access abnormality P. 5-98 1C22 Job control module access abnormality P. 5-98 1C30
Resumo do conteúdo contido na página número 15
2) RFC related error Message displayed in Error code Contents Troubleshooting the TopAccess screen 2500 Syntax error, command unrecog- HOST NAME error(RFC: 500) P. 5-101 nized Destination mail address error (RFC: 500) Terminal mail address error (RFC: 500) 2501 Syntax error in parameters or argu- HOST NAME error(RFC: 501) P. 5-101 2 ments Destination mail address error (RFC: 501) Terminal mail address error (RFC: 501) 2503 Bad sequence of commands Destination mail address error P. 5-101 (RFC: 5
Resumo do conteúdo contido na página número 16
3) Electronic Filing related error Message displayed in Error code Contents Troubleshooting the TopAccess screen 2B10 There was no applicable job. No applicable job error in job control P. 5-102 module 2B11 Job status failed. JOB status abnormality P. 5-102 2B20 Failed to access file. File library function error P. 5-102 2B30 Insufficient disk space. Insufficient disk space in /BOX parti- P. 5-102 tion 2B31 Failed to access Electronic Filing. Status of specified Electronic Filing P. 5-102 or fol
Resumo do conteúdo contido na página número 17
4) E-mail related error Message displayed in Error code Contents Troubleshooting the TopAccess screen 2C10 Illegal Job status System access abnormality P. 5-104 2C11 Not enough memory Insufficient memory P. 5-104 2C12 Illegal Job status Message reception error P. 5-104 2C13 Illegal Job status Message transmission error P. 5-104 2C14 Invalid parameter specified Invalid parameter P. 5-104 2 2C15 Message size exceeded limit or max- Exceeding file capacity P. 5-104 imum size 2C20 Illegal Job status
Resumo do conteúdo contido na página número 18
5) File sharing related error Message displayed in Error code Contents Troubleshooting the TopAccess screen 2D10 Illegal Job status System access abnormality P. 5-107 2D11 Not enough memory Insufficient memory P. 5-107 2D12 Illegal Job status Message reception error P. 5-107 2D13 Illegal Job status Message transmission error P. 5-107 2D14 Invalid parameter specified Invalid parameter P. 5-107 2D15 There are too many documents in the Exceeding document number P. 5-107 folder. Failed in creating n
Resumo do conteúdo contido na página número 19
6) E-mail reception related error Message displayed in Error code Contents Troubleshooting the TopAccess screen 3A10 MIME Error has been detected in the E-mail MIME error P. 5-109 received mail. 3A11 MIME Error has been detected in the P. 5-109 received mail. This mail has been transferred to the administrator. 3A12 MIME Error has been detected in the P. 5-109 2 received mail. This mail could not be transferred to the administrator. 3A20 Analyze Error has been detected in E-mail analysis error
Resumo do conteúdo contido na página número 20
Message displayed in Error code Contents Troubleshooting the TopAccess screen 3B20 Content-Type Error has been Content-Type error P. 5-109 detected in the received mail. 3B21 Content-Type Error has been P. 5-109 detected in the received mail. This mail has been transferred to the administrator. 3B22 Content-Type Error has been P. 5-109 detected in the received mail. This mail could not be transferred to the administrator. 3B30 Charset Error has been detected in Charset error P. 5-109 the rec
