Resumo do conteúdo contido na página número 1
B/W DIGITAL CAMERA MODULE
XCD-U100
XCD-SX90
XCD-V60
COLOR DIGITAL CAMERA MODULE
XCD-U100CR
XCD-SX90CR
XCD-V60CR
SERVICE MANUAL
1st Edition
Resumo do conteúdo contido na página número 2
! WARNING This manual is intended for qualified service personnel only. To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Refer all servicing to qualified service personnel. ! WARNUNG Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt. Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die Gefahr eines elektrischen Schlages, F
Resumo do conteúdo contido na página número 3
Table of Contents Manual Structure 3. Circuit Description Purpose of this manual ................................................................. 3 3-1. BI-217, BI-218, and BI-219 Boards ............................... 3-1 Related manuals ........................................................................... 3 3-2. FM-96 Board .................................................................. 3-1 3-3. IF-1068 Board .................................................................3-1 3-4. C
Resumo do conteúdo contido na página número 4
Resumo do conteúdo contido na página número 5
Manual Structure Purpose of this manual This manual is the Service Manual of the B/W Digital Camera Module XCD-U100/ SX90/V60 and Color Digital Camera Module XCD-U100CR/SX90CR/V60CR. This manual contains the service overview, adjustment, circuit description, spare parts, block diagrams, and frame wiring. The service of this unit is basically performed by the replacement of board. Therefore, the schematic diagram, board layout and electrical parts list are not contained. Related manuals In additi
Resumo do conteúdo contido na página número 6
Resumo do conteúdo contido na página número 7
Section 1 Service Overview 1-1. Board Location 1-2. Removing/Installing the Cabinet 1-2-1. Upper case/Lower case FM-96 board CN-3020 board 1. Remove the seven screws, then remove the upper case and lower case. PM2 x 4 DC-DC converter PM2 x 4 IF-1068 board PM2 x 4 Upper case BI-217/218/219 board PM2 x 4 Board name Model name BI-217 board XCD-V60 XCD-V60CR BI-218 board XCD-SX90 XCD-SX90CR BI-219 board XCD-U100 XCD-U100CR CN-3020 board Common DC-DC converter XCD-V60/V60CR/U100/U100CR Lower case XCD
Resumo do conteúdo contido na página número 8
1-2-2. Rear Panel Assembly 1-2-3. Front Panel Assembly 1. Remove the upper case and lower case. n (Refer to Section 1-2-1.) When replacing the front panel assembly, perform the 2. Remove the two screws, then pull out the rear panel writing the serial number and Node Unique ID and camera assembly. adjustment. For details, refer to Sections 2-1 and 2-2. 3. Disconnect the flexible flat cable from the connector (CN900) on the CN-3020 board. 1. Remove the upper case and lower case. (Refer to Section
Resumo do conteúdo contido na página número 9
1-3. Removing/Installing the Board 1-3-2. FM-96 Board 1-3-1. BI-217/218/219 Board n When replacing the FM-96 board, perform the writing of 1. Remove the upper case and lower case. the serial number and Node Unique ID. For details, refer to (Refer to Section 1-2-1.) Section 2-1. 2. Remove the front panel assembly. (Refer to Section 1-2-3.) 1. Remove the upper case and lower case. 3. Remove the two screws. (Refer to Section 1-2-1.) 4. Remove the solders of CCD, then remove the BI-217/ 2. Remove th
Resumo do conteúdo contido na página número 10
1-3-3. DC-DC Converter 1-3-4. IF-1068 Board 1. Remove the upper case and lower case. 1. Remove the upper case and lower case. (Refer to Section 1-2-1.) (Refer to Section 1-2-1.) 2. Remove the rear panel assembly. 2. Remove the rear panel assembly. (Refer to Section 1-2-2.) (Refer to Section 1-2-2.) 3. Remove the front panel assembly. 3. Remove the front panel assembly. (Refer to Section 1-2-3.) (Refer to Section 1-2-3.) 4. Remove the FM-96 board. (Refer to Section 1-3-2.) 4. Remove the FM-96 boa
Resumo do conteúdo contido na página número 11
1-3-5. CN-3020 Board 1. Remove the upper case and lower case. (Refer to Section 1-2-1.) 2. Remove the rear panel assembly. (Refer to Section 1-2-2.) 3. Remove the twelve solders of the connector from the CN-3020 board. 4. Remove the screw, then remove the CN-3020 board. Rear panel assembly Solders PM2 x 4 CN-3020 board 5. Install the CN-3020 board in the reverse order of steps 1 to 4. XCD-U100/SX90/V60 1-5 XCD-U100CR/SX90CR/V60CR
Resumo do conteúdo contido na página número 12
1-4. Lens Mount Cap, Filter Bracket, Optical Dust Cover (XCD-V60/SX90/ U100), Infrared Cut Filter (XCD-V60CR/SX90CR/U100CR), Sealing Rubber 1. Remove the upper case and lower case. 8. Attach the lens mount cap, filter bracket, optical dust (Refer to Section 1-2-1.) cover, infrared cut filter and sealing rubber in the 2. Remove the front panel assembly. (Refer to Section 1-2-3.) reverse order of steps 1 to 7. 3. Remove the lens mount cap. 4. XCD-V60/SX90/U100: Note for attaching the infrared cut
Resumo do conteúdo contido na página número 13
1-5. Round Type Connector (12-Pin) 1-7. Signal Inputs and Outputs 1. Remove the upper case and lower case. 2 (Refer to Section 1-2-1.) 2. Remove the rear panel assembly. (Refer to Section 1-2-2.) 3. Remove the CN-3020 board. (Refer to Section 1-3-5.) 4. Remove the nut and washer, then remove the round type connector (12-pin). 1 Rear panel 1 1 1 1 1 IEEE1394b connector . IEEE1394b-2002 Washer 9 5 Round type Nut connector (12-pin ) 1 4 — External view — 5. Attach the round type connector (12-pin)
Resumo do conteúdo contido na página número 14
1-8. Unleaded Solder Boards requiring use of unleaded solder are printed with a lead free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.) : LEAD FREE MARK m . Be sure to use the unleaded solder for the printed circuit board printed with the lead free mark. . The unleaded solder melts at a temperature about 40 dC higher than the ordinary solder, therefore, it is recom- mended to use
Resumo do conteúdo contido na página número 15
Section 2 Adjustment 2-1. Writing of Serial Number and Node 2. Click the “Adjust” tab and “Enter Adjust mode” tab. Unique ID The unit enters the adjustment mode. Adjust tab n Perform the writing when replacing the FM-96 board or front panel assembly. Required equipment . Personal computer (PC) xxxxxxxx xxxxxxxx xx . IEEE1394.b board . IEEE1394b cable (Commercially available products) . IIDC_CAM**** software: J-7120-410-A 3. Check the model nameplate on the bottom of this unit. (**** represents t
Resumo do conteúdo contido na página número 16
5. Click the “Flash” tab. 2-2. Camera Adjustment 6. Click the [Restart|the|Camera] button to restart. n Flash tab Perform the adjustment when replacing the front panel assembly. Required equipment . Personal computer (PC) . IEEE1394b cable(Commercially available products) [Restart|the|Camera] button . IIDC_CAM**** software: J-7120-410-A (**** represents the version number.) 7. Check if the serial number and Node Unique ID on the . Pattern box PTB-700: J-6431-850-A model nameplate correspond to e
Resumo do conteúdo contido na página número 17
2-2-1. Black and White (B/W) Camera 6. Click the Exposure tab and adjust the shutter in the (XCD-U100/SX90/V60) window so that the Green level reaches close to 100% (does not exceed 100% (236)) in the WFMwindow. 1. Shoot the pattern box in the center of the window The shutter value (reference value) at which the Green through the clear chart at the wide end. level reaches close to 100% on WFM is as follows. 2. Start the IIDC_CAM**** software. XCD-V60: 13 3. Click WFM (Waveform Monitor) in the me
Resumo do conteúdo contido na página número 18
Green level 2-2-2. Color Camera (XCD-U100CR/SX90CR/V60CR) 1. Shoot the pattern box in the center of the window through the clear chart at the wide end. 2. Start the IIDC_CAM**** software. 3. Click WFM (Waveform Monitor) in the menu. The waveform is displayed. WFM 7. Click the “Adjust” tab in the IIDC control window. [AdjustWB] button [Write] button xxxxxxxx xxxxxxxx xx [Gain0dB] button 4. Start the IIDC_CAM**** software. The IIDC control window is displayed. 8. Click the [AdjustWB] button to adj
Resumo do conteúdo contido na página número 19
Section 3 Circuit Description 3-1. BI-217, BI-218, and BI-219 Boards 3-3. IF-1068 Board These boards consist of CCD (IC101) and ADC (BI-217: This board consist of an oscillator (X800), an IC105), BI-218: IC102), and BI-219: IC105) that are used IEEE1394PHY layer (IC803), 1394 connectors (CN803 for VGA color/black & white (BI-217), SXGA color/black and CN804), and an external input signal isolation circuit & white (BI-218), and UXGA color/black & white (BI- (consisting of PH800, PH801, and PH802)
Resumo do conteúdo contido na página número 20
